Standard
PILOTED RING SEAL FLUID CONNECTION BOSSES
2023-10-13
CURRENT
AS685E
Search Results
Standard
CLIP - SPRING, TENSION, INNER 5 MM BOLT HOLE, AMS5525, METRIC
2023-10-13
CURRENT
MA3295A
Standard
Female Ferrule, Threadless - Flexible, Fixed Cavity, Self-Bonding Welded
2023-10-11
WIP
AS4736B
Revise FL4 to call out PRI-QPL AS1650 instead of source control.
Standard
WIRE, RETAINER - TUBE COUPLING NUT
2023-10-10
CURRENT
AS1791E
Standard
Torque Determination, Method of, For Tube or Hose End Fitting Connections, Flared, Flareless, or Miscellaneous Screw Thread Style
2023-10-02
CURRENT
ARP600C
This SAE Aerospace Recommended Practice (ARP) defines a method for determining a torque value (range) for threaded fluid connections.
Standard
Recommended Solid Film Lubricants for Fluid System Components
2023-10-02
CURRENT
ARP5824A
This SAE Aerospace Recommended Practice (ARP) provides recommended solid film lubricants for use on fluid system components at different temperatures and cyclic conditions.
Standard
Missile and Rocket Applications: Hose Assemblies, Flexible Metal, High Pressure and High Temperature
2023-10-02
CURRENT
ARP907A
This recommended practice covers the requirements and qualification tests for two types of flexible all-metal hose assemblies intended for hydraulic use on missile and rocket applications at rated pressures of 4000 psi. Type I -65° to +650 °F service temperature range Type II -65° to +1000 °F service temperature range
Standard
NUT, HEXAGON, DRILLED, BOSS CONNECTION, CRES - UNS S30400
2023-10-02
CURRENT
AS91001D
Standard
Fittings, Lubrication
2023-09-20
WIP
AS35411D
Rectify the Zinc coating callout by reinstating “Type 1” to the ASTM B 633 callout.
Standard
CLAMP, LOOP, TUBE 17-7PH, CUSHION, SELF-LOCKING
2023-09-18
CURRENT
AS6264A
Standard
Hose Assembly, Polytetrafluoroethylene (PTFE), Low Pressure, 450°F and Fireproof, Procurement Specification For
2023-09-13
WIP
AS4897
This SAE Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace fuel and lubricating oil systems at temperatures between -67 and 450°F and at operating pressures per Table 1. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this document, for example oxygen, shall be subject to the approval of the purchaser.
Standard
Guide for Choosing a Minimum Wall Thickness of Tubing for Use with Weld Fittings Coded for a Range of Wall Sizes
2023-09-11
CURRENT
ARP4698A
This SAE Aerospace Recommended Practice (ARP) is intended as a guide for choosing a minimum wall thickness of tubing, based only on pressure, for use with welded tube fitting ends that have a “tube wall code” covering a range of tube wall thicknesses. These wall thicknesses are based on burst pressure with an arbitrary additional safety factor. If the weld fitting user has already established the required minimum wall thickness for given performance conditions, this guide does not apply.
Standard
Weights, Tube Fitting, Estimating, Weighing and Maintaining, Procedure for
2023-09-11
CURRENT
ARP4961A
This SAE Aerospace Recommended Practice (ARP) establishes procedures for estimating the weight of parts, weighing actual parts at time of manufacture and maintaining and collecting the weight data.
Standard
Fluid Connections, Fittings, Hex Width
2023-09-11
CURRENT
ARP4919A
This SAE Aerospace Recommended Practice (ARP) is intended as a guide toward standard practice for selection of nominal hex widths for fittings.
Standard
Marking; Standard Hose, Aircraft
2023-09-11
CURRENT
ARP6002A
This document establishes the industry standard practices for marking standard elastomeric hose used in aircraft manufacture and repair.
Standard
FITTING ASSEMBLY, ELBOW 45°, REDUCER AND NONREDUCER, INTERNAL FLARE TO FLARED TUBE
2023-09-08
WIP
AS4409D
At the last revision the Procurement Spec was revised and was inadvertently changed to the QPL note. The Flared fittings are only QML’d parts. This revision corrects the error done at the last revision.
Standard
Fitting Assembly, Elbow 90°, Reducer and Nonreducer, Internal Flare to Flared Tube
2023-09-08
WIP
AS4407D
At the last revision the Procurement Spec was revised and was inadvertently changed to the QPL note. The Flared fittings are only QML’d parts. This revision corrects the error done at the last revision.
Standard
Hose Assembly, Polytetrafluoroethylene, Para-Aramid Reinforced, 5080 psi (35000 kPa), 275 °F (135 °C), Aircraft Hydraulic Systems
2023-09-07
WIP
AS5951E
Under paragraph 3.8.5 Cleaning; Removal of the use of alkaline cleaners only and update to align with all other hose assembly procurement specifications to specify cleaning to Class 0 of AS611.
Standard
Hose Assembly, Polytetrafluoroethylene, Metallic Braid Reinforced, 5080 psi (35000 kPa), 400 °F (204 °C), Aircraft Hydraulic Systems
2023-09-07
WIP
AS5960D
Under paragraph 3.9.2 Cleaning; Removal of the use of alkaline cleaners only and update to align with all other hose assembly procurement specifications to specify cleaning to Class 0 of AS611.
Standard
FITTING, UNION, FLARED TUBE, FOR SEAL RING
2023-09-05
CURRENT
AS1251D
