Search Results

A review of droplet sizing instruments used for icing research is presented. These instruments include the Forward Scattering Spectrometer Probe, the Optical Array Probe, the Phase Doppler Particle Analyzer, the Malvern Particle Size Analyzer, the oil slide technique, and the rotating multicylinder. The report focuses on the theory of operation of these instruments and practical considerations when using them in icing facilities.

This document is intended to serve two purposes: (1) provide a list of topics for potential customers to ask of the facility to aid their selection decision-making, and (2) provide a list of icing wind tunnel and engine test stand facilities that simulate flight through icing or ice crystal clouds.

This Icing Technology Bibliography is a compendium of references from the open literature, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the present Bibliography is not intended to be complete. However, it will be updated every 18 months by the SAE AC-9C Aircraft Icing Technology Subcommittee. Any suggestions in terms of additional references, sources, and corrections should be referred to the Icing Technology Bibliography Panel of the SAE AC-9C Aircraft Icing Technology Subcommittee.

Consolidate ice adhesion & accretion (and shedding) testing methods & define their applicability to real world icing conditions (need to define the attributes & processes) Document the physics governing ice adhesion strengths & accretion behaviors Define characteristics of ice formed in a range of atmosphere conditions Propose testing methods & facility requirements capable of differentiating ice adhesion consistently Define material properties affecting ice adhesion, including surface characteristics, preparation methods, and degradation Definitions of terminologies (ice types, atmosphere conditions, accretion dynamics, strengths & applicability (shear, tensile etc.), passive ice protection vs. active ice protection, etc.)

This document provides information on current practices for testing air data probes to 14 CFR Part 33 Appendix D ice crystal and mixed phase icing conditions. This AIR is primarily concerned with techniques for measuring the flow and icing environment in the test facility. While the focus of this report is the testing of air data probes, techniques described may be applicable to Appendix D tests of other aerospace equipment as well.

A review of icing materials that would be educational to a designer of a UAV ice protection system is provided. Additionally, the differences between unmanned and manned ice protection systems are explored along with a discussion on how these differences can be addressed.

This document is intended to provide guidance for development of a test matrix for generation of ice shapes on unprotected surfaces. It introduces the reader to scaling of flight conditions to capabilities of typical icing tunnels and provides an example of the process.

The new standard will establish minimum performance requirements for angle of attack (AOA) and angle of sideslip (AOS) sensors in ice and rain conditions. The new standard will cover the various sensor technologies used to measure these flow angles and is limited to the sensor itself as defined from the portion of the sensor that is directly exposed to the ice and rain environment to the means by which its output is relayed to the relevant aircraft systems. The user of this standard must evaluate the aircraft level installation requirements for the probe to ensure adequate coverage for the application. It may be necessary to modify the test conditions in order to meet the applicable installation requirements.

This SAE Aerospace Standard (AS) establishes minimum ice and rain performance criteria for electrically-heated pitot and pitot-static probes intended for use on the following classes of fixed-wing aircraft and rotorcraft. The classes of fixed-wing aircraft are defined by aircraft flight envelopes and are shown in Figure 1. The flight envelopes generally fall into the classes as shown below: The user of this standard must evaluate the aircraft level installation requirements for the probe against the class definition criteria to ensure adequate coverage for the application. It may be necessary to step up in class or modify the test conditions in order to meet the applicable installation requirements. NOTE: Class 2 is divided into two subgroups identified as either Class 2a or Class 2b. Class 2a probe applications typically include aircraft that operate within the mid to lower end of the Class 2 altitude range and that only use probe output to display basic airspeed and/or altitude.

This section presents the basic equations for computing ice protection requirements for nontransparent and transparent surfaces and for fog and frost protection of windshields. Simplified graphical presentations suitable for preliminary design, and a description of various types of ice, fog, frost, and rain protection systems are also presented.

This Icing Technology Bibliography is a compendium of references from the open literature that were published prior to the original 1987 issuance of the AIR, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the Bibliography in this document is not intended to be complete.

This Icing Technology Bibliography is a compendium of references from the open literature that were published prior to the original 1987 issuance of the AIR, including both national and foreign sources. Due to the generality of the subject, and the difficulty of fully investigating every available source, the Bibliography in this document is not intended to be complete.

This document is intended to provide guidance for conducting icing tunnel tests for assessment and design of thermal anti-ice systems for wing, stabilizers and engine inlets (considering both hot air and electrical power as a heat source).

This SAE Aerospace Information Report (AIR) presents and discusses the results of tests of three models in six icing wind tunnels in North America and Europe. This testing activity was initiated by the Facility Standardization Panel of the SAE AC-9C Aircraft Icing Technology Subcommittee. The objective of the testing activity was to establish a benchmark that compared ice shapes produced by icing wind tunnels available for use by the aviation industry and to use that benchmark as a basis for dialogue between facility owners to improve the state-of-the-art of icing wind tunnel technology.

This SAE Aerospace Information Report (AIR) presents and discusses the results of tests of three models in six icing wind tunnels in North America and Europe. This testing activity was initiated by the Facility Standardization Panel of the SAE AC-9C Aircraft Icing Technology Subcommittee. The objective of the testing activity was to establish a benchmark that compared ice shapes produced by icing wind tunnels available for use by the aviation industry and to use that benchmark as a basis for dialogue between facility owners to improve the state-of-the-art of icing wind tunnel technology.

This document contains minimum operational performance specification (MOPS) of active on-board INFLIGHT ICING DETECTION SYSTEMS (FIDS). This MOPS specifies FIDS operational performance which is the minimum necessary to satisfy regulatory requirements for the design and manufacture of the equipment to a minimum standard and guidance towards acceptable means of compliance when installed on an AIRCRAFT. Detection of ICE accreted on the AIRCRAFT during ground operations is not considered in this document. This MOPS was written for the use of FIDS on AIRCRAFT as defined in 1.3 and 2.3. Expected minimum performance specifications for FIDS and their functions are provided in Section 3. The minimum performance requirements as defined in Section 3 do not consider SYSTEM performance as installed on the AIRCRAFT. Performance in excess of the minimum performance may be required by the SYSTEM installed on an AIRCRAFT in order to meet regulatory or operational requirements.

The objective of this Minimum Operational Performance Specification is to specify the minimum performance of onboard inflight icing detection systems. Throughout the document, these devices are referred to as Flight Icing Detection Systems (FIDS). These systems are intended to either provide information which indicates the presence of ice accreted in flight on monitored surfaces or indicate the presence of icing conditions in the atmosphere. They may operate the airplane anti-ice/ deice systems. Detection of ice accreted on the ground is not considered in this document but can be found in ED-104. This MOPS was written for the use of FIDS on airplanes only, as defined in paragraph 1.5. Use on other aircraft may require additional considerations. Chapter 1 of this document provides information required to understand the need for the equipment characteristics and tests defined in the remaining chapters.