Search Results

Shadow positions can be useful in determining the time of day that a photograph was taken and determining the position, size, and orientation of an object casting a shadow in a scene. Astronomical equations can predict the location of the sun relative to the earth, and therefore the position of shadows cast by objects, based on the location’s latitude and longitude as well as the date and time. 3D computer software have begun to include these calculations as a part of their built-in sun systems. In this paper, the authors examine the sun system in the 3D modeling software Blender to determine its accuracy for use in accident reconstruction. A parking lot was scanned using Faro LiDAR scanner to create a point cloud of the environment. A camera was then set up on a tripod at the environment and photographs were taken at various times throughout the day from the same location in the environment.

Creating a 3-dimensional environment using imagery from small unmanned aerial systems (sUAS, or unmanned aerial vehicles -UAVs, or colloquially, drones) has grown in popularity recently in accident reconstruction. In this process, ground control points are placed at an accident scene and an sUAS is flown over an accident site and a series of overlapping, high resolution images are taken of the site. Those images and ground control points are then loaded onto a computer and processed using photogrammetric software to create a 3-dimensional point cloud or mesh of the site, which then can be used as a tool for recreating an accident scene. Many software packages have been created to perform these tasks, and in this paper, the authors examine RealityCapture, a newer photogrammetric software, to evaluate its accuracy for the use in accident reconstruction. It is the authors’ experience that RealityCapture may at times produce point clouds with less noise that other software packages.

Many motorcycle crashes involve the motorcycle capsizing, impacting the ground, and sliding on the road surface. When performing speed calculations, the energy or speed loss for the ground impact and sliding phases may need to be calculated. To perform these calculations, the reconstructionist will typically determine the slide distance based on the physical evidence and then apply a range of decelerations over that distance based on test data in the literature. Decelerations can be selected for motorcycles with similar characteristics (crash bars, panniers, fairings, etc.) sliding on similar surfaces (asphalt, concrete, dirt, gravel, etc.). This approach is adequate but sometimes results in a wide range due to the variability in reported decelerations in prior studies. It could be helpful to narrow the likely range of decelerations, and thus, the speed range.

When a motorcycle collides with a passenger vehicle, the impact can cause a change in the translational and rotational velocities of the struck vehicle. If these velocity changes, or the magnitude of the translation and rotation of the struck vehicle can be quantified, then these can potentially be used to calculate the impact speed of the motorcycle. There are several methods that could be used for this analysis. The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs - PC-Crash, HVE (the EDSMAC4 or SIMON modules), Virtual CRASH, or VCRware. However, these simulation programs can be time-consuming to apply and not everyone has access to them. It would be useful to have simple formulas for obtaining a reasonable estimate of the motorcycle impact speed based on the observed post-impact translation and rotation of the struck vehicle.

Small unmanned aerial systems have gained prominence in their use as tools for mapping the 3-dimensional characteristics of accident sites. Typically, the process of mapping an accident site involves taking a series of overlapping, high resolution photographs of the site, and using photogrammetric software to create a point cloud or mesh of the site. This process, known as image-based scanning, is explored and analyzed in this paper. A mock accident site was created that included a stopped vehicle, a bicycle, and a ladder. These objects represent items commonly found at accident sites. The accident site was then documented with several different unmanned aerial vehicles at differing altitudes, with differing flight patterns, and with different flight control software. The photographs taken with the unmanned aerial vehicles were then processed with photogrammetry software using different methods to scale and align the point clouds.

This paper reports testing and analysis of the braking and swerving capabilities of on-road, three-wheeled motorcycles. A three-wheeled vehicle has handling and stability characteristics that differ both from two-wheeled motorcycles and from four-wheeled vehicles. The data reported in this paper will enable accident reconstructionists to consider these different characteristics when analyzing a three-wheeled motorcycle operator’s ability to brake or swerve to avoid a crash. The testing in this study utilized two riders operating two Harley-Davidson Tri-Glide motorcycles with two wheels in the rear and one in the front. Testing was also conducted with ballast to explore the influence of passenger or cargo weight. Numerous studies have documented the braking capabilities of two-wheeled motorcycles with riders of varying skill levels and with a range of braking systems.

When reconstructing collisions involving left turning vehicles at intersections, accident reconstructionists are often required to determine the relative timing and spacing between two vehicles involved in such a collision. This time-space analysis frequently involves determining or prescribing a path and acceleration profile for the left turning vehicle. Although numerous studies have examined the straight-line acceleration of vehicles, only two studies have presented the tangential and lateral acceleration of left turning vehicles. This paper expands on the results of those limited studies and presents a methodology to automatically detect and track vehicles in a video file. The authors made observations of left turning vehicles at three intersections. Each intersection incorporated permissive green turn phases for left turning vehicles.

Previous studies have reported and validated equations for calculating the lean angle required for a motorcycle and rider to traverse a curved path at a particular speed. In 2015, Carter, Rose, and Pentecost reported physical testing with motorcycles traversing curved paths on an oval track on a pre-marked range in a relatively level parking lot. Several trends emerged in this study. First, while theoretical lean angle equations prescribe a single lean angle for a given lateral acceleration, there was considerable scatter in the real-world lean angles employed by motorcyclists for any given lateral acceleration level. Second, the actual lean angle was nearly always greater than the theoretical lean angle. This prior study was limited in that it only examined the motorcycle lean angle at the apex of the curves. The research reported here extends the previous study by examining the accuracy of the lean angle formulas throughout the curves.

PC-Crash is a vehicular accident simulation software that is widely used by the accident reconstruction community. The goal of this article is to review the prior literature that has addressed the capabilities of PC-Crash and its accuracy and reliability for various applications (planar collisions, rollovers, and human motion). In addition, this article aims to add additional analysis of the capabilities of PC-Crash for simulating planar collisions and rollovers. Simulation analysis of five planar collisions originally reported and analyzed by Bailey [2000] are reexamined. For all five of these collisions, simulations were obtained with the actual impact speeds that exhibited excellent visual agreement with the physical evidence. These simulations demonstrate that, for each case, the PC-Crash software had the ability to generate a simulation that matched the actual impact speeds and the known physical evidence.

This paper investigates the dynamics of four motorcycle crashes that occurred on or near a curve (Edwards Corner) on a section of the Mulholland Highway called “The Snake.” This section of highway is located in the Santa Monica Mountains of California. All four accidents were captured on video and they each involved a high-side fall of the motorcycle and rider. This article reports a technical description and analysis of these videos in which the motion of the motorcycles and riders is quantified. To aid in the analysis, the authors mapped Edwards Corner using both a Sokkia total station and a Faro laser scanner. This mapping data enabled analysis of the videos to determine the initial speed of the motorcycles, to identify where in the curve particular rider actions occurred, to quantify the motion of the motorcycles and riders, and to characterize the roadway radius and superelevation throughout the curve.

Calculating the speed of a yawing and braked vehicle often requires an estimate of the vehicle deceleration. During a steering induced yaw, the rotational velocity of the vehicle will typically be small enough that it will not make up a significant portion of the vehicle’s energy. However, when a yaw is impact induced and the resulting yaw velocity is high, the rotational component of the vehicle’s kinetic energy can be significant relative to the translational component. In such cases, the rotational velocity can have a meaningful effect on the deceleration, since there is additional energy that needs dissipated and since the vehicle tires can travel a substantially different distance than the vehicle center of gravity. In addition to the effects of rotational energy on the deceleration, high yaw velocities can also cause steering angles to develop at the front tires. This too can affect the deceleration since it will influence the slip angles at the front tires.

This paper presents a comprehensive literature review of original equipment event data recorders (EDR) installed in passenger vehicles, as well as a summary of results from the instrumented validation studies. The authors compiled 187 peer-reviewed studies, textbooks, legal opinions, governmental rulemaking policies, industry publications and presentations pertaining to event data recorders. Of the 187 total references, there were 64 that contained testing data. The authors conducted a validation analysis using data from 27 papers that presented both the EDR and corresponding independent instrumentation values for: Vehicle velocity change (ΔV) Pre-Crash vehicle speed The combined results from these studies highlight unique observations of EDR system testing and demonstrate the observed performance of original equipment event data recorders in passenger vehicles.

Improvements in computer image processing and identification capability have led to programs that can rapidly perform calculations and model the three-dimensional spatial characteristics of objects simply from photographs or video frames. This process, known as structure-from-motion or image based scanning, is a photogrammetric technique that analyzes features of photographs or video frames from multiple angles to create dense surface models or point clouds. Concurrently, unmanned aircraft systems have gained widespread popularity due to their reliability, low-cost, and relative ease of use. These aircraft systems allow for the capture of video or still photographic footage of subjects from unique perspectives. This paper explores the efficacy of using a point cloud created from unmanned aerial vehicle video footage with traditional single-image photogrammetry methods to recreate physical evidence at a crash scene.

Several sources report simple equations for calculating the lean angle required for a motorcycle and rider to traverse a curved path at a particular speed. These equations utilize several assumptions that reconstructionists using them should consider. First, they assume that the motorcycle is traveling a steady speed. Second, they assume that the motorcycle and its rider lean to the same lean angle. Finally, they assume that the motorcycle tires have no width, such that the portion of the tires contacting the roadway does not change or move as the motorcycle and rider lean. This study reports physical testing that the authors conducted with motorcycles traversing curved paths to examine the net effect of these assumptions on the accuracy of the basic formulas for motorcycle lean angle. We concluded that the basic lean angle formulas consistently underestimate the lean angle of the motorcycle as it traverses a particular curved path.

In a 2012 paper, Brach, Brach, and Louderback (BBL) investigated the uncertainty that arises in calculating the change in velocity and crush energy with the use of the CRASH3 equations (2012-01-0608). They concluded that the uncertainty in these values caused by variations in the stiffness coefficients significantly outweighed the uncertainty caused by variations in the crush measurements. This paper presents a revised analysis of the data that BBL analyzed and further assesses the level of uncertainty that arises in CRASH3 calculations. While the findings of this study do not invalidate BBL's ultimate conclusion, the methodology utilized in this paper incorporated two changes to BBL's methodology. First, in analyzing the crash test data for several vehicles, a systematic error that is sometimes present in the reported crush measurements was accounted for and corrected.

PC-Crash™, a widely used crash analysis software package, incorporates the capability for modeling non-constant vehicle acceleration, where the acceleration rate varies with speed, weight, engine power, the degree of throttle application, and the roadway slope. The research reported here offers a validation of this capability, demonstrating that PC-Crash can be used to realistically model the build-up of a vehicle's speed under maximal acceleration. In the research reported here, PC-Crash 9.0 was used to model the full-throttle acceleration capabilities of three vehicles with automatic transmissions - a 2006 Ford Crown Victoria Police Interceptor (CVPI), a 2000 Cadillac DeVille DTS, and a 2003 Ford F150. For each vehicle, geometric dimensions, inertial properties, and engine/drivetrain parameters were obtained from a combination of manufacturer specifications, calculations, inspections of exemplar vehicles and full-scale vehicle testing.

This paper reports a method for analyzing data from a DriveCam unit to determine impact speeds and velocity changes in vehicle-to-vehicle impacts. A DriveCam unit is an aftermarket, in-vehicle, event-triggered video and data recorder. When the unit senses accelerations over a preset threshold, an event is triggered and the unit records video from two camera views, accelerations along three directions, and the vehicle speed with a GPS sensor. In conducting the research reported in this paper, the authors ran four front-to-rear crash tests with two DriveCam equipped vehicles. For each test, the front of the bullet vehicle impacted the rear of the stationary target vehicle. Each of the test vehicles was impacted in the rear twice - once at a speed of around 10 mph and again at a speed around 25 mph. The accuracy of the DriveCam acceleration data was assessed by comparing it to the data from other in-vehicle instrumentation.

Accurately reconstructing the speed of a yawing and braking vehicle requires an estimate of the varying rates at which the vehicle decelerated. This paper explores the accuracy of several approaches to making this calculation. The first approach uses the Bakker-Nyborg-Pacejka (BNP) tire force model in conjunction with the Nicolas-Comstock-Brach (NCB) combined tire force equations to calculate a yawing and braking vehicle's deceleration rate. Application of this model in a crash reconstruction context will typically require the use of generic tire model parameters, and so, the research in this paper explored the accuracy of using such generic parameters. The paper then examines a simpler equation for calculating a yawing and braking vehicle's deceleration rate which was proposed by Martinez and Schlueter in a 1996 paper. It is demonstrated that this equation exhibits physically unrealistic behavior that precludes it from being used to accurately determine a vehicle's deceleration rate.