Search Results

The refrigerant transition from HFC-134a to HFO-1234yf has proven to be more challenging on controlling refrigerant flow-induced noises generated from automotive air-conditioning (A/C) systems than originally anticipated. The objectives of this paper are to describe the noise issues with HFO-1234yf, understand the mechanisms and key factors affecting HFO-1234yf refrigerant flow-induced noise. Finally, the countermeasures and guidelines for attenuating and suppressing the noise are presented.

In the thermal expansion valve (TXV) refrigerant system, transient high-pitched whistle around 6.18 kHz is often perceived following air-conditioning (A/C) compressor engagements when driving at higher vehicle speed or during vehicle acceleration, especially when system equipped with the high-efficiency compressor or variable displacement compressor. The objectives of this paper are to conduct the noise source identification, investigate the key factors affecting the whistle excitation, and understand the mechanism of the whistle generation. The mechanism is hypothesized that the whistle is generated from the flow/acoustic excitation of the turbulent flow past the shallow cavity, reinforced by the acoustic/structural coupling between the tube structural and the transverse acoustic modes, and then transmitted to evaporator. To verify the mechanism, the transverse acoustic mode frequency is calculated and it is coincided to the one from measurement.

Refrigerant flow-induced gurgling noise is perceived in automotive refrigerant systems. In this study, the condition of the gurgling generation is investigated at the vehicle level and the fundamental root cause is identified as the two-phase refrigerant flow entering the TXV for system equipped with variable displacement compressors. By conducting literature reviews, the acoustic characteristics of the flow patterns and the parameters affecting the flow regimes in horizontal and vertical tubes are summarized. Then the gurgling mechanism is explained as the intermittent flow is developed at the evaporator inlet. In the end, the improved and feasible design for avoiding the intermittent flow (slug, plug or churn flow) or minimizing its formation is proposed and verified in refrigerant subsystem (RSS) level. Finally, the guidelines for the attenuation and suppression of the gurgle are provided.

This paper presents the methodology of predicting vehicle level automotive air-handling system air-rush noise sound quality (SQ) using the sub-system level measurement. Measurement setup in both vehicle level and sub-system levels are described. To assess the air-rush noise SQ, both 1/3 octave band sound pressure level (SPL) and overall Zwicker's loudness are used. The “Sound Quality Correlation Functions (SQCF)” between sub-system level and vehicle level are developed for the specified climate control modes and vehicle segment defined by J.D. Power & Associates, while the Zwicker's loudness is calculated using the un-weighted predicted 1/3 octave band SPL. The predicting models are demonstrated in very good agreement with the measured data. The methodology is applied to the development of sub-system SQ requirement for upfront delivery of the optimum design to meet global customer satisfaction

This paper presents the development of a novel direct coil cooling approach which can enable high performance for electric traction motor, and in further significantly reduce motor losses. The proposed approach focuses on bypassing critical thermal resistances in motor by cooling coils directly in stator slots with oil flow. Firstly, the basic configuration and features are shown: sealed stator slots to air gap, pressure reservoirs on both side of the slots and slot channels for oil flow. The key to enhance thermal performance of the motor here is based on introducing fluid guiding structure in the slot channels. Next, heat transfer in the channel with guiding structure is investigated by CFD and compared with bare slot channel without guiding structure. For studying the effectiveness of proposed cooling concept, numerical analysis is conducted to compare it with HEV favored oil impingement cooling.

Air-conditioning (A/C) induced moan is a very commonly observed phenomenon in automotive refrigerant systems. Since most of the automotive A/C systems cycle ON/OFF four to six times every minute, the A/C induced moan is quite readily audible under engine idle and even while driving, especially under lower engine/vehicle speeds. It is not unusual for an A/C compressor to moan or not, on some vehicle/s under certain operating conditions. Most of the OEMs resolve or suppress the A/C moan potential to barely audible levels. However, under some unique and extreme operating conditions, A/C moan is quite readily induced and often results in customer complaints. This paper discusses A/C moan related root-causes, sources and paths of propagation. A systematic diagnostic test-procedure is also described to diagnose and develop the needed most cost-effective design-fixes. Finally, based on this case-study - some objective targets are recommended to suppress the A/C moan to acceptable levels.

Transient higher-frequency flow-induced tones are often perceived following air-conditioning (A/C) compressor engagements in automotive refrigerant systems, especially the ones with Thermostatic Expansion Valve (TXV) controlled systems. In this paper, the mechanisms of the acoustic tones induced by turbulent flow and shear-layer-instability in A/C lines are presented. Some of the recommended countermeasures for the attenuation and suppression of these flow-induced transient tones are also discussed.

The automotive refrigerant systems can occasionally exhibit a transient hoot/whistle type noise under certain operating conditions. High pressure/velocity refrigerant flow through an evaporator core can readily excite the inherent acoustical and/or structural modes, resulting in audible transient tones. This condition if present can be experienced while driving away from a short stop and can last 2 to 10 seconds. The ambient conditions suitable for creating this noise are - moderate/high air-conditioning (A/C) load during days at 85-95° F temperatures with high humidity. Possible noise generating mechanisms have been discussed in earlier publications and our findings during this study indicate that they are excited by the high velocity superheated refrigerant vapor flow through the evaporator core plates. Examples of this transient noise and its spectral characteristics are presented to characterize this refrigerant system induced issue.

Automotive refrigerant system induced noise and vibration transients usually accompany A/C compressor engagement/disengagement. These transients include audible/perceivable metallic impact/slip (clink, chirp, etc.), engagement thump, delayed accumulator thump, orifice tube/TXV induced hiss, and occasionally very loud slugging. In this paper, the inherent noise source mechanisms of these transients are described, and a set of psychoacoustics based objective metrics quantifying these transients in terms of loudness and sharpness is developed. Some of the recommended design-fixes and noise control approaches for the related transient noises are also discussed.