Search Results

Military and civilian vehicles are moving towards more electrification, in response to the increasing demand for multi-mode missions, fuel consumption and emissions reduction, and dual use electrical and electronic components. Consequently, the vehicle electric load is increasing rapidly. For military vehicles, these electrical loads include: the loads for electric traction (EV and HEV), cabin climate conditioning, vehicle control and actuation, actuation by wire (X by wire), sensors, reconnaissance, communications, weapons etc. All these requirements need to be supported by an efficient, fast responding and high capacity energy storage system. The electric load of a vehicle can be decomposed into two components--- static and dynamic loads. The static component is slowly varying power with limited magnitude, whereas the dynamic load is fast varying power with large magnitude. The energy storage system, accordingly, comprises of two basic elements.

Due to their harsh operating environments, military vehicle drive trains have special requirements. These special requirements are usually represented by hill climbing ability, obstacle negotiation, battlefield cross country travel, hard acceleration, high speed, etc. These special requirements need the vehicle drive train to have a wider torque and speed range characteristics than commercial vehicles. We have proved that larger constant power ratio in electric motor can significantly enhance the vehicle acceleration performance. In other words, for the same acceleration performance, large constant power ratio can minimize the power rating of the traction motor drive, thus minimizing the power rating of the power source (batteries for instance). Actually, extension of the constant power range can also significantly enhance the gradeability, which is crucial for military vehicles.

Significant amount of energy is lost in frequent braking, automatic transmission and engine idling for a conventional engine powered passenger car while driving in cities. In this paper, a mild hybrid vehicle drive train has been introduced. It uses a small electric motor with floating stator, called TRANSMOTOR and small and a battery pack. The transmotor functions as a generator, engine starter, frictionless clutch (electric torque coupler), regenerative braking and propelling. The mild hybrid drive train can effectively reduce the urban-driving fuel consumption by regenerative braking, eliminate of energy losses in conventional automatic transmission and engine idling. The drive train can use low voltage system (42V for example), due to the low electric power rating, and is more similar to conventional drive train than full hybrid vehicle. Therefore, less effort is needed to evolve it from conventional vehicles.

In this paper, a mild hybrid drive train has been proposed. A small electric motor with low rated voltage (42 V) is used to (1) propel the vehicle at low speed, (2) replace the fluid-coupled torque converter and (3) realize regenerative braking. With proper design and control, the fuel economy in urban driving can be significantly improved without much change from conventional drive train to the mild hybrid drive train.

The desirable braking system of a land vehicle is that it can stop the vehicle or reduce the vehicle speed as quickly as possible, maintain the vehicle direction stable and recover kinetic energy of the vehicle as much as possible. In this paper, an electronically controlled braking system for EV and HEV has been proposed, which integrates regenerative braking, automatic control of the braking forces of front and rear wheels and wheels antilock function together. When failure occurs in the electric system, the braking system can function as a conventional man-actuated braking system. Control strategies for controlling the braking forces on front and rear wheels, regenerative braking and mechanical braking forces have been developed. The braking energy that can be potentially recovered in typical driving cycle has been calculated. The antilock performance of the braking system has been simulated.

A general design methodology of the fuel cell powered hybrid vehicle drive train has been developed. With the methodology and a computer simulation program, all of the systematic parameters can be designed, such as, the rated power of the electric motor drive, fuel cell system, peaking power source as well as the energy capacity. An overall control strategy has also been developed. The main function of the control strategy is to properly control the power produced by the fuel cell system and the peaking power source, so as to meet the power demand, maintain the energy level of the peaking power source in its optimal region and operate the fuel cell system within its high efficiency region. In this paper, a design example has also been introduced in each section.

There is a growing interest in electric and hybrid electric vehicles (EV and HEV) due to their high efficiency and low emission. In EV and HEV, the characteristic of the traction motor is essential for the performance and efficiency of the EV and HEV. In this paper, the advantages of the extended constant power range characteristic of the traction motor for both propulsion and regenerative braking are analyzed. Simulation results are presented to verify the conclusions. Due to its several inherent advantages, especially its capability of having an extended constant power range, Switched Reluctance Motor (SRM) is proposed as the candidate of the traction motor in EV and HEV. The design methodology of SRM for achieving an extended constant power range and the control strategy of SRM for regenerative braking in EV and HEV are presented.

The possibility of recovering vehicle kinetic energy is one inherent advantage of electric and hybrid electric vehicles. When a vehicle drives in heavy traffic, for example in New York City, more than half of the total energy is dissipated in the brakes. Therefore, recovering braking energy is an effective approach for improving the driving range of EV and the energy efficiency of HEV. In this paper, three different braking patterns are investigated for evaluating the availability of braking energy recovery. The results indicate that even without active braking control, a significant amount of braking energy can be recovered, and the brake system does not need much changing from the brake systems of conventional passenger cars.

In this paper, the configuration of a parallel hybrid vehicle, called electrically peaking hybrid (ELPH) vehicle is introduced. Several operation modes of the engine and electric motor and different control strategies are analyzed. The results show that, with proper selection of the drivetrain parameters, the vehicle can satisfy the urban and highway driving with a small internal combustion engine, a small battery pack and a single gear transmission. Moreover, the vehicle does not need to charge the battery pack from the electricity network for keeping its battery SOC at a reasonable level.

The operation of an electrically peaking hybrid vehicle (ELPH) can be divided into two basic modes. • Constant or cruising speed mode in which a small internal combustion engine (ICE) is used to power the vehicle. • Peak power mode in which the combination of an electric motor and ICE is used to supply peak power for acceleration and limited-duration steep hill climbing of the vehicle. A method, by which the engine size and the speed reduction ratio from the engine to drivewheels can be developed based on the cruising mode, is presented in this paper. The electric motor power rating and the motor gear ratio to the drive wheels can then be determined, based on the acceleration and gradeability. The results show that a simple single-gear transmission would be a good selection for overall performance.