Search Results

Accurate estimation of battery state of health (SOH) has become indispensable in ensuring the predictive maintenance and safety of electric vehicles (EVs). While supervised machine learning excels in laboratory settings with adequate SOH labels, field-based SOH data collection for supervised learning is hindered by EVs' complex conditions and prohibitive data collection costs. To overcome this challenge, a battery SOH estimation method based on semi-supervised regression is proposed and validated using field data in this paper. Initially, the Ampere integral formula is employed to calculate SOH labels from charging data, and the error of labeled SOH is reduced by the open-circuit voltage correction strategy. The calculation error of the SOH label is confirmed to be less than 1.2%, as validated by the full-charge test of the battery packs.

Accurate fault diagnosis is critical to the safe and efficient operation of lithium-ion battery systems. However, various faults in battery systems are difficult to detect and isolate due to their similar features. This paper proposes a model-based multi-fault diagnosis method to detect and isolate the current, voltage, and temperature sensor faults, short circuit faults, and connection faults in the lithium-ion battery systems. An electro-thermal model with fault information is established and used to construct the structural model. Structural analysis theory is applied to design diagnostic tests sensitive to multiple faults. To improve the accuracy and robustness of residual generation, the adaptive extended Kalman filter is introduced to battery state estimation. The multi-fault detection and isolation are implemented using residual evaluation based on the cumulative sum algorithm.

Due to traffic congestion and environmental pollution, connected automated vehicle (CAV) technologies based on vehicle-to-vehicle (V2V) and vehicle-to-infrastructure communication (V2I) have gained increasing attention from both academia and industry. Connected hybrid electric vehicles (CHEVs) offer great opportunities to reduce vehicular operating costs and emissions. However, in complex traffic scenarios, high-quality real-time energy management of CHEVs remains a technical challenge. To address the challenge, this paper proposes a hierarchical eco-driving strategy that consists of speed planning and energy management layers. At the upper layer, by leveraging the real-time traffic data provided by vehicle-to-everything (V2X) communication, dynamic traffic constraints are predicted by the traffic flow predictor developed based on the Hankel dynamic mode decomposition algorithm (H-DMD).

The core idea of advanced eco-driving is to optimize the vehicle’s speed and acceleration profile from the energy point of view using real-time data from the vehicle to vehicle (V2V) and vehicle to infrastructure (V2I). However, the main assumption of most of the existing advanced eco-driving approaches is that vehicles are maintained on a single-lane road that considers only the longitudinal motion of the vehicle. In multi-lane roads, controlling the lateral movement of the vehicle or the dynamic lane-changing along with the longitudinal movement can have a positive effect on traffic flow, travel time, fuel economy, and exhaust emission of the vehicle. This paper presents a bi-level model predictive control strategy for connected and automated hybrid electric vehicles (CAHEVs) to optimize inter-vehicle safety, energy-saving, and emission reduction while considering both the lateral and longitudinal motions of the vehicle.

Plugin Hybrid Electric Vehicles (PHEV) have a large battery which can be used for electric only powertrain operation. The control system in a PHEV must decide how to spend the energy stored in the battery. In this paper, we will present a prototype implementation of a PHEV control system which saves energy for electric operation in pre-defined geographic areas, so called Green Zones. The approach determines where the driver will be going and then compares the route to a database of predefined Green Zones. The control system then reserves enough energy to be able to drive the Green Zone sections in electric only mode. Finally, the powertrain operation is modified once the vehicle enters the Green Zone to ensure engine operation is limited. Data will be presented from a prototype implementation in a Ford Escape PHEV Presenter Johannes Kristinsson

This paper presents a low-cost path for extending the range of small urban pure electric vehicles by hydraulic hybridization. Energy management strategies are investigated to improve the electric range, component efficiencies, as well as battery usable capacity. As a starting point, a rule-based control strategy is derived by analysis of synergistic effects of lead-acid batteries, high efficient operating region of DC motor and the hydraulic pump/motor. Then, Dynamic Programming (DP) is used as a benchmark to find the optimal control trajectories for DC motor and Hydraulic Pump/Motor. Implementable rules are derived by studying the optimal control trajectories from DP. With new improved rules implemented, simulation results show electric range improvement due to increased battery usable capacity and higher average DC motor operating efficiency.

Energy security and climate change challenges provide a strong impetus for investigating Electric Vehicle (EV) concepts. EVs link two major infrastructures, the transportation and the electric power grid. This provides a chance to bring other sources of energy into transportation, displace petroleum and, with the right mix of power generation sources, reduce CO₂ emissions. The main obstacles for introducing a large numbers of EVs are cost, battery weight, and vehicle range. Battery health is also a factor, both directly and indirectly, by introducing limits on depth of discharge. This paper considers a low-cost path for extending the range of a small urban EV by integrating a parallel hydraulic system for harvesting and reusing braking energy. The idea behind the concept is to avoid replacement of lead-acid or small Li-Ion batteries with a very expensive Li-Ion pack, and instead use a low-cost hydraulic system to achieve comparable range improvements.