Search Results

In the context of carbon neutrality, ammonia is considered a zero-carbon fuel with potential applications in the transportation sector. However, its high ignition energy, low flame speed, and high natural temperature, indicative of low reactivity, make it challenging to be applied as a sole fuel in engines. In such a scenario, the use of another zero-carbon and highly reactive fuel, hydrogen, becomes necessary to enhance the combustion of ammonia. Furthermore, jet ignition, a method known for improving engine combustion performance, may also hold potential for enhancing the combustion performance of ammonia engines. To explore the applicability of jet ignition in engines, this study conducted experimental research on a single-cylinder engine. Two ignition methods were employed: passive jet ignition of premixed ammonia-hydrogen at a compression ratio of 11.5, and active jet ignition of pure ammonia using hydrogen jet flame at a compression ratio of 17.3.

Ammonia (NH3), a zero-carbon fuel, has great potential for internal combustion engine development. However, its high ignition energy, low laminar burning velocity, narrow range of flammability limits, and high latent heat of vaporization are not conducive for engine application. This paper numerically investigates the feasibility of utilizing ammonia in a heavy-duty diesel engine, specifically through low-pressure direct injection (LP-DI) of hydrogen to ignite ammonia combustion. Due to the lack of a well-corresponding mechanism for the operating conditions of ammonia-hydrogen engines, this study serves only as a trend-oriented prediction. The paper compares the engine's combustion and emission performance by optimizing four critical parameters: excess air ratio, hydrogen energy ratio, ignition timing, and hydrogen injection timing. The results reveal that excessively high hydrogen energy ratios lead to an advanced combustion phase, reducing indicated thermal efficiency.

Octane number (ON) and octane sensitivity (S), the fuel anti-knock indices, are critical for the design of advanced jet ignition engines. In this study, ten fuels with different research octane number (RON) and varying S were formulated based on ethanol reference fuels (ERFs) to investigate the effect of S on combustion of jet ignition engine. To fully understand S effects, the combustion characteristics under EGR dilution and lean burn were further investigated. The results indicated that increasing S resulted in higher reactivity with shorter ignition delay and combustion duration. The increase of reactivity led to heavier knocking intensity. The competition between the flame speed and the reactivity of the mixture determined the auto-ignition fraction of mixture and the knocking onset crank angle as S varied. Medium S (S=3) was helpful to improve the combustion speed, reduce the auto-ignition fraction of mixture and retard the knocking onset crank angle.

A real-time control is proposed for Plug-in Hybrid Electric Vehicles (PHEVs) based on the optimal Dynamic Programming (DP) trajectories in this study. Firstly, the DP is used to solve the Driving Cycle to obtain the optimal trajectories and controls, and the Model-Based Calibration tool (MBC) is used to generate the optimal Maps for the given optimal trajectories. Secondly, a Feedback Energy Management System (FMES) is built with State of Charge (SoC) as the feedback variable, which takes into account the Charge and Discharge Reaction (CDR) of the battery.

Vehicle-to-vehicle (V2V) communication is an important part of intelligent transportation system. With the vigorous development of expressway construction, it is of great significance to study the propagation characteristics of V2V communication channels in the scene of expressway under construction. This paper describes in detail the V2V broadband channel measurement activity carried out on the A96 expressway in the suburb of Munich, Germany. Based on the measured data, the variation of signal receiving power while the vehicle was moving is analyzed. We focus on the small-scale fading characteristics of expressway sections under construction in the C-band. The results show that the magnitude of received signal varies rapidly while vehicles are moving. Comparing the measurement data with theoretical distributions, it has been found that the magnitudes of measurement data on the expressway under construction fit the best to the Rice distribution.

Currently, most of vehicle recognition methods are realized by deep convolutional neural networks (DCNNs) with input of images directly as training data. Due to the factor of perspective distortion and scale change of images taken by monocular camera, a large number of multi-scale images need to be used for training, and physical information of vehicles cannot be obtained at the same time. In order to improve the above problems, we present a method of vehicle recognition based on unpacking 3D bounding boxes in this paper. Firstly, camera calibration information and geometric constraints are used to build 3D bounding boxes around vehicles in monocular projection. Then, the 3D bounding boxes are unpacked to obtain 3D normalized spatial data without perspective distortion. Finally, VGG-16 is chosen as the backbone of our network, the output of which can be divided into five common vehicle types including hatchback, sedan, SUV, truck and bus.

With the advent of autonomous vehicles, the human driver’s attention will slowly be relinquished from the driving task. It will allow drivers to participate in more non-driving related activities, such as engaging with information and entertainment systems. However, the automated driving system would need to notify the driver of upcoming points-of-interest on the road when the driver’s attention is focused on their screen rather than on the road or driving display. In this paper, we investigated whether providing directional alerts for an upcoming point-of-interest (POI) in or around the user’s active screen can augment their ability in relocating their visual attention to the POI on the road when traveling in a vehicle with Conditional Driving Automation. A user study (N = 15) was conducted to compare solutions for alerts that presented themselves in the participants’ central and peripheral field of view.

A 24GHz multi-function assist system has been developed for advanced automotive radar, which includes different applications in Blind Spot Detection (BSD), Lane Change Assist (LCA), Doors Open Warning (DOW) and Rear Cross Traffic Alert (RCTA). The multi-function radar is based on the micro-strip antenna, which has a reasonable design on main-lobe and side-lobes. According the antenna, the radar can operate in mid-range mode with a high gain and a narrow beam width, whilst performing well in short-range and wide-angle mode.

Comparing with traditional braking systems of automobiles, the brake-by-wire (BBW) system has a faster dynamic response and is more suitable for applications that facilitate regenerative braking. As the two main categories of BBW systems, the well-known electro-hydraulic braking system and electro- mechanical braking system are not compact enough and their fail-safe function has always been a worrying aspect. A new BBW system called integrated braking system (IBS) by employing the hydraulic multiplex method was proposed in recent years. The IBS implements power-assisted braking and active braking by means of just an integrated unit. It can certainly be used for ABS, ASR and ESC systems for building up and reducing brake pressure. Presented in the paper is a new structure of IBS, which is mainly composed of a motor, ball screw, master cylinder and four 2/2-way valves.

An automotive vehicle should be designed to satisfy the wants of customers. The key is how to convert voices of customers into engineering languages. In other words, transfer the wants of customers into the right technical characteristics of a vehicle. A questionnaire of customer wants for a CUV (Crossover Utility Vehicle) is created and processed. Using QFD (Quality Function Deployment) and modified KANO model, the relative important degree is obtained from the original relative important degree of customer wants surveyed. Since some information gained is uncertain and the questionnaire sample is limited, a gray correlation analysis method is introduced, which calculates the competitive important degree of customer wants, then the final important degree of customer wants is gained by integrating the relative important degree and the competitive important degree.

Current gasoline-gas vapor recovery system is incomplete, for it cannot adjust the vapor-liquid ratio automatically due to the change of working temperature. To solve this problem, this paper intends to design a new system and optimize its parameters. In this research, variables control method is used for tests while linear regression is used for data processing. This new system moves proportion valve away and adds a DSP control module, a frequency conversion device, and a temperature sensor. With this research, it is clearly reviewed that the vapor-liquid ratio should remains 1.0 from 0 °C to 20 °C as its working temperature, be changed into 1.1 from 20 °C to 25 °C, be changed into 1.2 from 25 °C to 30 °C, and be changed into 1.3 when the working temperature is above 30 °C.

The adhesion control is the basic technology of active safety for the four-wheel driven EV. In this paper, a novel adhesion control method based on fuzzy logic control is proposed. The control system can maximize the adhesion force without road condition information and vehicle speed signal. Also, the regulation torque to prevent wheel slip is smooth and the vehicle driving comfort is greatly improved. For implementation, only the rotating speed of the driving wheel and the motor driving torque signals are needed, while the derived information of the wheel acceleration and the skid status are used. The simulation and road test results have shown that the adhesion control method is effective for preventing slip and lock on the slippery road condition.

A new technique for measuring the friction coefficient between the punch and workpiece during sheet forming operations has been developed at the Ohio State University. Various materials, such as interstitial-free (IF) steel, high strength (HS) steel, an aluminum alloy (2008T4) and 70/30 brass, were tested under dry and oil lubrication conditions at different punch rates and process conditions. The results show that punch friction depends on the angle of wrap, which varies with punch stroke, and on the strain rate, which depends on punch velocity. The O.S.U. Friction Test is described and typical results are presented which verify the usefulness of the new procedure.