Search Results

Conversion from diesel to dual fuel (diesel and natural gas) operation may represent an attractive retrofit technique to get a better PM-NOx trade-off in a diesel engine, with no major modifications of the original design. In the proposed paper, an Euro 2 heavy duty diesel engine, converted for dual fuelling, has been studied and tested to reduce pollutant emissions. Throttled stoichiometric with EGR and lean burn technologies have been selected as control strategies. A mixed experimental-numerical approach has been utilized to analyze the engine behavior by varying key operating conditions such as throttling, natural gas/diesel oil percentage and EGR. The model, based on a 3D approach, has been used mainly to understand the evolution of the distribution of the most important parameters in the combustion chamber.

The paper presents a 1D-3D numerical model to simulate the scavenging and combustion processes in a small-size spark-ignition two-stroke engine. The engine is crankcase scavenged and can be operated with both gasoline and Natural Gas (NG). The analysis is performed with a modified version of the KIVA3V code, coupled to an in-house developed 1D model. A time-step based, two-way coupled procedure is fully described and validated against a reference test. Then, a 1D-3D simulation of the whole two-stroke engine is carried out in different operating conditions, for both gasoline and NG fuelling. Results are compared with experimental data including instantaneous pressure signals in the crankcase, in the cylinder and in the exhaust pipe. The procedure allows to characterize the scavenging process and quantify the fresh mixture short-circuiting, as well as to analyze the development of the NG combustion process for a diluted mixture, typically occurring in a two-stroke engine.

Dual-fuel engines, based on the use of natural gas (NG) as the main fuel in internal combustion engines (ICE) and using diesel injection as the ignition source instead of the spark plug, are one of the possible ways to reduce the trade off PM-NOX problem of traditional diesel engines. The high octane number (NOR) of NG allows to easily covert existing diesel engine, without varying the original compression ratio, with great advantages in terms of costs. The only modifications concern with the introduction of feeding system for NG and the reduction of diesel quantity injected into the combustion chamber, by acting on injection pump control. For high degrees of substitution, diesel oil can be considered only as the ignition source for the fresh air/NG mixture, with consequent beneficial effects on PM emissions. The real drawback regarding dual-fuel engines is the wide increase in HC and CO emissions and efficiency worsening, especially under part-load conditions.

The modern common rail Diesel engines are normally optimised for being fuelled with the commercial Diesel fuel. Consequently, the ECU calibrations are defined to realize the best compromise between performances and emissions. If the engine is fuelled with an alternative biofuel with different characteristics (net heating value, stoichiometric A/F ratio, density, viscosity, etc.) it is clear that the calibration must be modified. Interest in fuels from renewable sources and their use in transportation has grown over the last decade. This is because of their biodegradability, potential improvements in exhaust emissions and benefits on the virtuous CO2 cycle of the earth. This paper demonstrates that it is possible to optimise emissions and performances of a light duty C.R. Diesel engine fuelled with a vegetable derived fuel (Rapeseed Methyl-Ester) pure or blended with commercial Diesel fuel.

One of the possible solutions in order to reduce NOX and PM emissions and fuel specific consumption in a diesel engine is to substitute a part of the diesel oil with a gaseous fuel. Natural gas, due to the high octane number, allows such substitution without great modifications to the original engine, just introducing the gas feeding system. The utilization of natural gas (usually referred as “alternative fuel”) instead of oil is an important advantage of such technology in terms of energy sources. In this paper the conversion of the IVECO 8360.46R engine, for bus applications, to dual-fuel operations is discussed. Experimental tests were performed to define the general behaviour of the engine, especially at partial loads. Main target of the present study was the analysis of engine requirements to maintain the same output load as the full-diesel operation, and controlling exhaust emissions.

Interest in fuels from renewable sources and their use in transport has grown over the last decade. This is because of their biodegradability, potential improvements in exhaust emissions and benefits on the virtuous CO2 cycle of the earth. Biodiesel fuels can be derived from rapeseed, sunflowers, and other kind of seeds or from UFO (Used Fried Oil). This paper analyses the results of an experimental study fuelling a Common Rail Diesel Engine with a 100% rapeseed Biofuel, with a blend of rapeseed and UFO biodiesel and compares it with commercial diesel fuel Other papers by the same authors compared the different physic-chemical characteristics of biofuels, against diesel fuel and the consequent different spray characteristics that affect the combustion phenomenon. These characteristics are correlated with the different performances and emissions obtained in the experimental activity when a modern Common Rail light duty diesel engine is adopted.

The correct simulation of combustion process allows to better face several SI engines design problems, not only for innovative mixture formation concepts (stratified or ultra-lean charge), but for traditional homogeneous mixture as well. Even though many commercial codes are able to describe the complex 3-D non reacting fluid dynamics in ICE, the simulation of high turbulent flame propagation does not seem to be a completely solved problem yet. In this work a comparison between two different turbulent combustion models (a characteristic time based one by Abraham and Reitz [2, 15, 16] and a flamelet based one by Cant and AbuOrf [4, 20]) has been performed using KIVA-3V code to assess simulation reliability. Models predictive capabilities have been tested with reference to specific data acquired at the engine test bench of Tor Vergata Mechanical Engineering Department on a Fiat Punto 1242 cc 8 valves SI engine over a wide range of operating conditions.

The recent innovations on automotive Diesel engines require significant research efforts. The new generation of fully electronically controlled injection systems have opened new ways to reduce emissions and improve the efficiency of the engine. The free mapping of injection law together with the enhanced injection pressures favor, in fact, the optimization of mixture formation. In this field, the 3D simulation is playing a substantial role to support the design of combustion chamber. This paper presents a computational model to simulate the multi-injection process, the mixture formation and the combustion of DI diesel engines with high-pressure injection systems. The main code is a modified version of the KIVA 3V and the modifications presented in this work are a high pressure break up model and a multi component evaporation model. The code has been validated through experimental data on a 4-cylinder, 1910 cc, DI turbocharged Diesel engine (Fiat 1.9 JTD).

The use of Compressed Natural Gas as an alternative fuel in urban transportation is nearly established and represents an efficient short and medium term solution to face with urban air pollution. However, in order to completely exploit its potential, the engine needs to be specifically designed to operate with this fuel. In the latest years, the authors have investigated the performances of a Heavy Duty Turbocharged CNG fuelled engine both experimentally and by using some analytical tools specifically developed by them which have been used for the engine optimisation. In the present paper the simulation approach has been enlarged by means of a co-operative use of a CFD code and experimental analysis on the actual engine. The numerical simulation of combustion process has, in fact, been used, to interpret series of pressure cycles, aiming to analyse how cyclic fluctuations influence engine behaviour in terms of combustion efficiency and temperature and pollutant distribution.

The 1997 Kyoto International Conference Protocol committed industrialized countries to reduce their global emissions of greenhouse gases within the period 2008 2012 by at least 5% with respect to 1990. In view of this and following the European Community directives, the Italian government approved a three-year pilot project to promote the experimental employment of biodiesel. The methyl esters of vegetable oils, known as biodiesel are receiving increasing interest because of their low environmental impact and their potential as an alternative fuel for diesel engines as they would not require any significant modification of existing engines. Consequently, an experimental research program has been developed to evaluate performance and emissions of a Diesel engine fueled with a methyl ester derived from rape seed (Rapeseed Methyl Ester or RME) by changing the composition of the diesel fuel-RME mixture. This program aims to analyze the performance and emissions of a turbocharged D.I.

The first part of the paper gives an overview of the current status in fuel consumption gain of the GDI-vehicles previously launched on the European market. In order to increase the potential for a further gain in specific fuel consumption the behaviour of 3 different combustion chamber layouts are studied. The chamber layouts are aimed to adapt as well as possible to the particular requirements for application to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application that shows the different steps of a structured optimisation methodology for a 1.2 litre, small bore 4-cylinder engine. The applications of an air-motion-guided and a wall-guided layout with a mechanically actuated valve train to the same combustion chamber are discussed. The potential of the air-motion-guided concept is enhanced through the introduction of an electromagnetic fully variable valve train.

The first part of the paper gives an overview of the current development status of the GDI system layout for the middle displacement engine, typically 2 liter, using the stoichiometric or weak lean concept. Hereafter are discussed the particular requirements for the transition to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application of the different steps of the optimization methodology for a 1.2 liter, small bore 4 cylinder engine from its original base line MPI version towards the lean stratified operation mode. The latest changes in the combustion model, used in the numerical simulation software applied to the combustion chamber design, are discussed and comparison made with the previous model. The redesign of the combustion chamber geometry, the proper choice of injector atomizer type and location and the use of two-stage injection and multi-spark strategies are discussed in detail.

The suggestions for upcoming Euro 2000 clean air act puts an increasing legislative pressure for lower specific fuel consumption in order to reduce the emission of CO2 and thereby decrease the impact of the “green house” effect. One of the possible suggestions to meet these requirements for SI-engines is the gasoline direct injected (GDI) power unit. One of the key points of the success of a layout of a GDI system is the optimization of the fuel injector and combustion chamber charge formation parameters. A brief description of the basic GDI-system used during the study is given. Hereafter are outlined the computational and experimental optimization tools which have been used to produce, on a reasonable industrial time scale, the main indications to optimize the design of a given injector/chamber configuration. The paper discusses in detail the results produced by the latest enhancements introduced into the 3D multi-phase computational approach, NCF-3D.

Pollutant emissions from D.I. Diesel engines strongly depend on injection system characteristics and mainly on injection pressure and timing. In the latest years some solutions have been proposed based on very high fuel pressure values (up to 150 MPa). Among them, the so called “Common rail” system configuration, being able to electronically control needle lift and injection pressure, seems to be particularly promising. Much experimental and theoretical work has been done to improve system performance for automotive applications. With the aim of investigating the influence of some details of geometrical configuration on the injector operating mode, a mathematical model able to describe the pressure-time history in any section of the delivery pipe and the fuel injection rate through the nozzle has been developed, based on a semi-implicit finite volumes approach. The computed results have been compared with experimental data provided by the Institut Français du Pétrole.

The first part of the paper outlines the main potential advantages of the direct fuel injection concept and describes the overall layout of a system in which the keystones are a piston rotary fuel delivery pump with integrated pressure regulation and electromechanical fast responding fuel injectors. Three different nozzle designs are discussed, a divergent pintle solid cone, a pintle hollow cone swirl layout and a closed cap multijet design. In the second part of the paper the used experimental high pressure dynamic test equipment is discussed. Then the results obtained by the use of phase illuminated visualisation techniques and phase Doppler analysis as well as by a 3D CFD approach are presented. The paper concludes by relating the spray patterns and the associated droplet penetration velocities, produced by the different nozzle types, to the combustion chamber layout and to the possible manufacturing precision requirements for each nozzle type.

The modeling of the combustion process inside D.I. compression ignition engines has become extremely important for both improving combustion efficiency and describing the conditions in which pollutant emissions formation occurs. However simulation codes results are greatly dependent on the history of fuel droplets injected into combustion chamber, which have to vaporize before mixing with air. Actually fuel jet evaporation phase is particularly critical as far as its rate is concerned. In fact it largely affecs the it initial period of the combustion process. Simplified evaporation models can lead to unrealistic air-fuel ratio distribution in the combustion chamber and, as a consequence, to wrong heat release rate. An incorrect description of heat release rate still turns out into wrong evaluation of premixed and diffusive combustion periods, thus involving scarcely precise predicted profiles on both pressure and burned mass fraction.

In-cylinder pressure time history is usually measured in order to calculate both indicated mean effective pressure, as a global engine performance index, and the rate of heat release, as a quantitative information about combustion progress. Generally such information is readily provided by acquisition systems in terms of heat release rate, which is computed by means of simple inverse models based on first law of thermodynamics. Nevertheless attention must be paid to any measurement uncertainty connected to pressure cycle relief which directly results into inaccurate heat release analysis. As far as i.m.e.p. evaluation is concerned, a wrong adjustment of T.D.C. reference position, leading to incorrect pressure-crank angle phasing, had been recognized as the major error source.