Search Results

It is important to reduce the diffusion polarization for achieving higher performance in direct methanol fuel cells (DMFC). The previous research has shown the performance improvement by applying a metal foam type porous stainless steel made by a metal-plating method to the separator flow field of a DMFC. This porous flow field enabled DMFC to operate with higher power output than conventional straight groove type separator especially at higher current densities. Diffusion polarization was especially reduced by the porous flow field. This current paper experimentally analyzes the effect of a new type porous flow field that is made of a sintered spherical metal powder. The results show that the sintered metal powder flow field exhibits higher effect in performance improvement of DMFC than the metal foam type porous flow field used in the previous research.

This paper presents the studies carried out on electrolysis of aqueous methanol for hydrogen production in a proton exchange membrane electrolyser with a novel porous flow field made of sintered metal powder. Results show that the use of porous flow field has a significant improvement in hydrogen production performance compared to a groove flow field. This could be attributed to an increase in effective electrode area and to a reduction in diffusion polarization by using the porous material which enables the flow field to supply reactants evenly to the electrode and also removes carbon dioxide smoothly. Influences of the operating conditions such as methanol concentration and cell temperature on hydrogen production are also discussed.

Unregulated emissions from a DI diesel engine with ultra-high EGR low temperature combustion were analyzed using Fourier transform infrared (FTIR) spectroscopy and the reduction characteristics of both regulated and unregulated emissions by two exhaust catalysts were investigated. With ultra-high EGR suppressing the in-cylinder soot and Nox formation as well as with the exhaust catalysts removing the engine-out THC and CO emissions, clean diesel operation in terms of ultra-low regulated emissions (Nox, PM, THC, and CO) is established in an operating range up to 50% load. To realize smokeless low temperature combustion at higher loads, EGR has to be increased to a rate with the overall (average) excess air ratio less than the stoichiometric ratio.

The effects of blending ETBE to diesel fuel on the characteristics of low temperature diesel combustion and exhaust emissions were investigated in a naturally-aspirated DI diesel engine with large rates of cooled EGR. Low temperature smokeless diesel combustion in a wide EGR range was established with ETBE blended diesel fuel as mixture homogeneity is promoted with increased premixed duration due to decreases in ignitability as well as with improvement in fuel vaporization due to the lower boiling point of ETBE. Increasing the ETBE content in the fuel helps to suppress smoke emissions and maintain efficient smokeless operation when increasing EGR, however a too high ETBE content causes misfiring at larger rates of EGR. While the NOx emissions increase with increases in ETBE content at high intake oxygen concentrations, NOx almost completely disappears when reducing the intake oxygen content below 14 % with cooled EGR.

The effects of intake dilution with various dilution gases including nitrogen, argon, and carbon dioxide on low temperature diesel combustion were investigated in a naturally aspirated DI diesel engine to understand the mechanism of the simultaneous reductions in smoke and NOx with ultra-high EGR. NOx almost completely disappears with the intake oxygen concentration diluted below 16% regardless of the kind of dilution gas. Smoke emissions decrease with increased heat capacity of the charged gas due to promotion of mixture homogeneity with longer ignition delays. Intake dilution with the 36% CO2 + 64% Ar mixture which has a similar specific heat capacity as N2 shows lower smoke emissions than with N2. Chemical kinetics analysis shows that carbon dioxide may help to reduce NOx and soot by lowering the reaction temperature as well as by changing the concentrations of some radicals or/and species related to soot and NOx formation.

Palm oil has the important advantage of productivity compared to other vegetable oils such as rapeseed oil and soybean oil. However, the cold flow performance of palm oil methyl ester (PME) is poorer than other vegetable oil based biodiesel fuels. Previous research by the authors has shown that ethanol blending into PME improves the cold flow performance and considerably reduces smoke emission. The reduced smoke may be expected to allow an expansion in the EGR limit and lead to reduced NOx. This paper experimentally analyses the influence of EGR on smoke and NOx emissions from the diesel combustion with PME/ethanol blended fuel. The mechanisms in the smoke reduction are also analyzed.

A homogeneous-charge compression-ignition (HCCI) engine system that was fuelled with dimethyl ether (DME) and methanol-reformed gas (MRG) has been proposed in the previous research. Adjusting the proportion of DME and MRG can effectively control the ignition timing of the engine. In the system, both fuels are to be produced from methanol in onboard reformers utilizing the engine exhaust gas heat. While hydrogen contained in MRG has the main role of the ignition control, hydrogen increases with carbon dioxide in the methanol reforming. This paper investigates the influence of carbon dioxide on HCCI combustion engine with the ignition control by hydrogen. Both thermal and chemical effects of carbon dioxide are analyzed.

The dependence of ultra-high EGR low temperature diesel combustion on fuel properties including cetane number and distillation temperature was investigated with a single-cylinder, naturally aspirated, 1.0 L, common rail DI diesel engine. Decreasing cetane number in fuels significantly reduces smoke emission due to an extension in ignition delay and the subsequent improvement in mixture formation. Smokeless combustion, ultra-low NOx, and efficient operating range with regard to EGR and IMEP are significantly extended by decreasing fuel cetane number. Changes in fuel distillation temperature do not result in significant differences in smoke emission and thermal efficiency for ultra-high EGR operation, and smokeless operation is established even with higher distillation temperature fuels as long as fuel cetane number is sufficiently low.

The purpose of this study is to improve low-temperature flow-properties of biodiesel fuels (BDF) by blending with ethanol and to analyze the combustion characteristics in a diesel engine fueled with BDF/ethanol blended fuel. Because ethanol has a lower solidifying temperature, higher oxygen content, lower cetane number, and higher volatility than BDF, ethanol blending would have a large effect on cold flow performance, mixture formation, ignition, combustion, and exhaust emissions. The engine experiments in the study were performed with a diesel engine and blends of BDF and ethanol at different blending ratios. The cold flow performance of the blended fuels was evaluated by determining the fuel cloud point. The experimental results show that the ethanol blending lowers the cloud point of the blended fuel and significantly reduces smoke emissions from the engine without deteriorating other emissions or thermal efficiency.

Adjusting the proportion of two fuels with different ignition properties is an effective technique for controlling ignition timing in homogeneous charge compression ignition (HCCI) combustion. One of the authors has proposed an HCCI combustion engine system fueled with dimethyl ether (DME) with a high cetane number and methanol reformed gas (MRG) with a high anti-knock property in the previous research. Both DME and MRG are to be produced from methanol by onboard reformers utilizing the exhaust heat from the engine in the system. The research has shown that adjusting the proportion of DME and MRG effectively controlled the ignition timing and load in HCCI combustion of the two fuels. High overall thermal efficiency has been shown over a wide operable range. While the MRG used in the research was the thermally decomposed methanol, which consists of hydrogen and carbon monoxide, methanol can be reformed into various compositions of hydrogen, carbon monoxide and carbon dioxide.

Homogeneous charge compression ignition (HCCI) combustion enables higher thermal efficiency and lower NOx emission to be achieved in internal combustion engines when compared with conventional combustion systems. Control of proportion of high cetane number and low cetane number fuels is an effective technique for controlling ignition timing and load in HCCI combustion. The aim of this paper is to analyze the characteristics of the HCCI combustion of hydrogen, carbon monoxide and dimethyl ether (DME) in a single cylinder engine. A mixture of hydrogen and carbon monoxide with a composition of 67% hydrogen and 33% carbon monoxide called methanol-reformed gas (MRG) was used as the low cetane number fuel and DME as the high cetane number fuel. Both MRG and DME can be reformed from methanol in endothermic reactions. The endothermic reactions make waste heat recovery in fuel reforming possible by using the heat from the exhaust gases.

This study analyzes the factors influencing the thermal efficiency of a homogeneous charge spark-injection (SI) engine fuelled with hydrogen, focusing on the degree of constant volume and cooling loss. The cooling loss from the burning gas to the cylinder walls is quantitatively evaluated by analyzing the cylinder pressure diagram and exhaust gas composition. The degree of constant volume burning and constant volume cooling are also obtained by fitting the Wiebe function to the rate of heat release calculated using the cylinder pressure diagram. A comparison of combustion and cooling characteristics of hydrogen and methane combustion reveals that cooling loss in hydrogen combustion is higher than that of methane combustion due to the short quenching distance and rapid burning velocity during hydrogen combustion. It is also suggested that the high cooling loss observed during hydrogen combustion reduces thermal efficiency.

Reformed fuel from hydrocarbons or alcohol mainly consists of hydrogen, carbon monoxide and carbon dioxide. The composition of the reformed fuel can be varied to some extent with a combination of a thermal decomposition reaction and a water gas shift reaction. Methanol is known to decompose at a relatively low temperature. An application of the methanol reforming system to an internal combustion engine enables an exhaust heat recovery to increase the heating value of the reformed fuel. This research analyzed characteristics of combustion, exhaust emissions and cooling loss in an internal combustion engine fueled with several composition of model gases for methanol reformed fuels which consist of hydrogen, carbon monoxide and carbon dioxide. Experiments were made with both a bottom view type optical access single cylinder research engine and a constant volume combustion chamber.

Methanol has many advantages as a fuel for fuel cells compared with hydrogen. The direct methanol type system consists of simple and compact equipment, and suited for automobile use. This research analyzed characteristics of power output and thermal efficiency in a direct methanol fuel cell. The measuring system for low concentration methanol in a water solution using the non-dispersive infrared (NDIR) was developed. Influences of electrolyte membrane thickness, cell temperature, and methanol solution concentration on power output and thermal efficiency were analyze.

Characteristics of methane direct injection spark ignition stratified combustion in lean hydrogen mixture were analyzed both in a single cylinder engine and in a constant volume combustion vessel. Combustion pressure and instantaneous combustion chamber wall temperature during combustion process were measured and used in analysis of combustion and cooling loss. Results in this research show the premixed hydrogen increases cooling loss to combustion chamber wall while achieving combustion promotion, and the combustion system is effective especially in lean mixture conditions. Analysis of flame propagation was also done with schlieren photography in the constant volume combustion vessel.

Hybrid electric vehicle with internal combustion engine fueled with hydrogen can be a competitor to the fuel cell electric vehicle that is thought to be the ultimately clean and efficient vehicle. The objective in this research is to pursue higher thermal efficiency and lower exhaust emissions in a hydrogen-fueled engine for the series type hybrid vehicle system. Influences of compression ratio, surface / volume ratio of combustion chamber, and boost pressure on thermal efficiency and exhaust emissions were analyzed. Results showed that reduction of the surface / volume ratio by increased cylinder bore was effective to improve indicated thermal efficiency, and it was possible to achieve 44% of indicated thermal efficiency. However, brake thermal efficiency resulted in 35.5%. It is considered that an improved mechanical efficiency by an optimized engine design could increase the brake thermal efficiency largely.

A new concept DISC engine equipped with a two-stage injection system was developed. The engine was modified from a single cylinder DI diesel engine with large cylinder diameter (135mm). Combustion characteristics and exhaust emissions with regular gasoline were examined, and the experiments were also made with gasoline-diesel fuel blends with higher boiling temperatures and lower octane numbers. To realize stratified mixture distribution in combustion chamber flexibly, the fuel was injected in two-stages: the first stage was before the compression stroke to create a uniform premixed lean mixture and the second stage was at the end of the compression stroke to maintain stable ignition and faster combustion. In this paper, the effect of the two-stage injection on combustion and exhaust emissions were analyzed under several operating conditions.