Search Results

While vehicular rear pole impacts are rare, they do occur, and can be very serious. General accident reconstruction methods, which derive vehicle stiffness values from rear barrier crash tests, over-predict the impact speed for these types of pole impacts. Thirteen pole crash tests were run into the rear-ends of four 4-door, front-wheel drive sedans. Repeated crash testing was used on three of the vehicles. Two 1988 Acura Legends, which have one of the highest stiffness values from FMVSS 301 Rear Compliance crash testing, a 1988 Honda Civic, which has one of the softest rear-end stiffnesses, and a 1986 Ford Taurus were tested. The repeated crash testing methodology was validated using one of the 1988 Acura Legends and a previously published Ford Taurus test. Residual crush was measured using maximum crush, point-to-point, longitudinal full-width, and longitudinal reduced-width methodologies. Crush was found to be linearly related to impact speed.

Understanding occupant kinematics is an important part of accident reconstruction, particularly with respect to injury causation. Injuries are generally sustained as the occupant interacts with the vehicle interior surfaces and is rapidly accelerated to the struck component's post-impact velocity. This paper describes some methods for assessing occupant kinematics in a collision, and discusses their limitations. A useful technique is presented which is based on free-body analysis and can be used to establish an occupant's path of motion relative to the vehicle, locate the point of occupant contact, and determine the occupant's velocity relative to that contact location.

Occupant simulation models have been used to study trends or specific design changes in “typical” accident modes such as frontal, side, rear, and rollover. This paper explores the usage of the Articulated Total Body Program (ATB) as an accident reconstruction tool. The importance of model validation is discussed. Specific areas of concern such as the contact model, force-deflection data, occupant parameters, restraint system models, head/neck loadings, padding, and intrusion are discussed in the context of accident reconstruction.

Claims have been made that many production seatbelt buckles unlatch inertially during collisions. These claims are based on “parlor tricks” in which the back of the buckle is slapped, causing inertial release. Investigations of the potential for such inertial release in real-world collisions have consistently concluded that it is not a safety concern. Engineering analyses indicate that loadings experienced by buckles in real-world collisions are substantially different from the loadings which cause buckles to open in “parlor tricks.”

Recent cadaver studies have provided data for the development of force and stiffness characteristics of the side of the human head. A Hybrid III Anthropomorphic Test Dummy (ATD) head was modified to allow direct measurement of impact forces on the parietal and temporal regions by recasting the upper left half of the skull and installing triaxial piezoelectric force transducers. Dynamic impact tests of this modified head were conducted and force/stiffness characteristics for the temporal and parietal areas were compared to existing data on cadaver subjects. It was found that the existing Hybrid III vinyl skin satisfactorily represents the force/stiffness characteristics of the human head in these areas. This modified Hybrid III dummy head was also impacted against typical interior components likely to be contacted during a side impact. The force and acceleration test results are presented.

Recent detailed field accident data are examined with regard to injuries associated with rear impacts. The distribution of “Societal Harm” associated with various injury mechanisms is presented, and used to evaluate the performance of current seat back and restraint system designs. Deformation associated with seat back yield is shown to be beneficial in reducing overall Societal Harm in rear impacts. The Societal Harm associated with ejection and contact with the vehicle rear interior (the two injury mechanisms addressed by a rigid seat approach), is shown to be minimal. The field accident data also confirm that restraint usage in rear impacts has a substantial injury-reducing effect. Laboratory tests and computer simulations were run to investigate the mechanism by which seat belts protect occupants in rear impacts.

Impact tests were conducted on thirty-one unembalmed human cadaver heads. Impacts were delivered to the temporo-parietal region of fixed cadavers by two, different sized, flat-rigid impactors. Yield fracture force and stiffness data for this region of the head are presented. Impactor surfaces consisted of a 5 cm2 circular plate and a 52 cm2 rectangular plate. The average stiffness value observed using the circular impactor was 1800 N/mm, with an average bone-fracture-force level of 5000 N. Skull stiffness for the rectangular impactor was 4200 N/mm, and the average fracture-force level was 12,500 N.

Recently obtained force-deflection information for the frontal, zygomatic and maxillary regions of the human cadaver head and the Hybrid III ATD head indicates need for a redesigned Anthropomorphic Test Dummy (ATD) face. A prototype, deformable, load-sensing face (DLSF) was designed, with human-like-force-deflection compliant materials. The face was divided into six load sensing segments. The force level and impact location as a function of time can be determined for each segment, as well as for a selected set of segments and the whole face. The prototype face underwent preliminary testing for comparison with available cadaver data.

Results of two studies concerning the interrelationship of velocity, compression and injury in blunt thoracic impact to anesthetized swine have been combined to provide a data base of forty-one experiments. impact velocity ranged from ∼8-30 m/s and applied normalized chest compression from ∼0.10-0.30. Experimental subjects were suspended in the spine-horizontal position and loaded midsternally through a 150 mm diameter, flat rigid disk on an impacting mass propelled upward from below. Measurements and computations included sternal and spinal accelerations, intracardiovascular overpressures, physiological responses, injury, as assessed by necropsy, and different forms of the velocity and compression exposure severity parameters. The significance of both compression and velocity as parameters of impact exposure severity is clearly demonstrated. Qualitatively, exacerbation of injury was seen when either variable was increased with the other held constant.

The Simulation Model of Automobile Collisions (SMAC) computer program has seen more than a decade of use under NHTSA auspices. Although SMAC has proven itself to be a useful investigative tool, the program has several shortcomings which either have been addressed by the authors or need to be addressed by further work. This paper presents the results of our ongoing work to improve SMAC and our recommendations for further work. Those model features discussed herein which either have been or need to be revised consist of (1) the calculation of crush forces when penetration is deep (2) the representation of the vehicles' crush pressure vs deflection relationship and (3) the distribution of tire normal forces in reaction to pitch and roll. An input interfacing program called SMACED has been written and is discribed. This editing program greatly simplifies the use of SMAC and will be found particularly useful for the inexperienced or infrequent SMAC user.

Computer-aided crash reconstruction has become common-place in the automotive safety profession, primarily because of widespread distribution of software under public auspices. The SMAC (Simulation Model of Automobile Collisions) program, for instance, is available through NHTSA at nominal cost. This paper exhibits some of the limitations and strengths of accident reconstruction simulations, with illustrations and emphasis drawn from the SMAC program. In particular, some coarse physical approximations used and some coding errors incurred in the formulation of SMAC are discussed, together with their respective effects on the accuracy of prediction. Revisions of the basic SMAC coding have been developed at BYU to overcome these shortcomings. Results of uncorrected and revised SMAC simulations are demonstrated by comparison with the physical theory. Comments regarding a new SMAC program just completed under U.S. Government contract are presented where appropriate.