Search Results

Standard

RECOMMENDED PRACTICE FOR BAR-CODED VEHICLE IDENTIFICATION NUMBER LABEL

1994-07-08

HISTORICAL

J1877_199407

This SAE Recommended Practice describes the basic content requirements, bar code specifications, and functional test specifications of the vehicle identification number (VIN) label. On the vehicle, the VIN label is to be mounted in a readily accessible location for use of a bar-code scanning device.

Standard

RECOMMENDED PRACTICE FOR BAR-CODED VEHICLE IDENTIFICATION NUMBER LABEL

1988-05-01

HISTORICAL

J1877_198805

This recommended practice describes the basic content requirements, bar-code specifications, and functional test specifications of the vehicle identification number (VIN) label. On the vehicle, the VIN label is to be mounted in a readily accessible location for use of a bar-code scanning device.

Standard

TRUCK IDENTIFICATION TERMINOLOGY

1981-12-01

HISTORICAL

J1229_198112

This SAE Recommended Practice is intended to provide uniform nomenclature and definitions for the primary levels of vehicle identification, with particular application to trucks.

Standard

VEHICLE IDENTIFICATION NUMBERS

1981-12-01

HISTORICAL

J853_198112

This SAE Standard has been established to provide direction for the design and installation of a Vehicle Identification Number assigned to a passenger car or truck. In adhering to these standards, facility of application in factory production and appearance are matters for manufacturer control.

Standard

PASSENGER CAR IDENTIFICATION TERMINOLOGY

1981-12-01

HISTORICAL

J218_198112

This recommended practice is intended to provide uniform nomenclature and definitions for the primary levels of vehicle identification, with particular application to passenger cars.

Standard

TRUCK AND TRUCK TRACTOR VEHICLE IDENTIFICATION NUMBER SYSTEMS

1981-12-01

HISTORICAL

J1108_198112

This practice supplements SAE J272c. It applies to characteristics of truck and truck tractor descriptive and identifying information which are to be set forth in a uniform manner in the vehicle identification number.

Standard

PASSENGER CAR VEHICLE IDENTIFICATION NUMBER SYSTEM

1981-12-01

HISTORICAL

J273_198112

This practice supplements SAE J272c. It applies to characteristics of passenger car descriptive and identifying information which are to be set forth in a uniform manner in the vehicle identification number.

Standard

ENGINE AND TRANSMISSION IDENTIFICATION NUMBERS

1981-12-01

HISTORICAL

J129_198112

This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number as assigned to passenger car and truck engines and transmissions. In adhering to these recommended practices, facility of application in factory production and appearance are matters for manufacturer control. Reference SAE J853.

Standard

VEHICLE IDENTIFICATION NUMBER SYSTEMS

1981-12-01

HISTORICAL

J272_198112

This recommended practice describes general characteristics of VIN systems. It includes certain specific requirements, supporting definitions, basic content, and examples.

Standard

WORLD MANUFACTURER IDENTIFIER

1981-12-01

HISTORICAL

J1044_198112

This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853a, J187, J272b, J273a, J1108, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle tilting and registration, law enforcement, and theft recovery.

Standard

TRUCK IDENTIFICATION TERMINOLOGY

1978-05-01

HISTORICAL

J1229_197805

This SAL Recommended Practice is intended to provide uniform nomenclature and definitions for the primary levels of vehicle identification, with particular application to trucks. While this specific terminology applies only to trucks, work is in progress to develop supplementary nomenclature and definitions pertaining to other commercial vehicle terms and to terms presently used interchangeably in passenger car, truck, or other commercial vehicle applications. The supplementary terms will be covered in subsequent revisions to this recommended practice.

Standard

WORLD MANUFACTURER IDENTIFIER

1978-02-01

HISTORICAL

J1044A_197802

This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853a (November, 1968), J187 (October, 1970), J272b (September, 1977), J273a (September, 1977), and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.

Standard

TRUCK AND TRUCK TRACTOR VEHICLE IDENTIFICATION NUMBER SYSTEMS

1977-09-01

HISTORICAL

J1108_197709

Standard

VEHICLE IDENTIFICATION NUMBER SYSTEMS

1977-09-01

HISTORICAL

J272B_197709

This recommended practice describes general characteristics of VIN systems. It includes certain specific requirements, supporting definitions, basic content, and examples.

Standard

WORLD MANUFACTURER IDENTIFIER

1977-09-01

HISTORICAL

J1044A_197709

This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853a, J187, J272b, J273a, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.

Standard

PASSENGER CAR VEHICLE IDENTIFICATION NUMBER SYSTEM

1977-02-01

HISTORICAL

J273A_197702

This practice supplements SAE J272a. It applies to characteristics of passenger car descriptive and identifying information which are to be set forth in a uniform manner in the vehicle identification number.

Standard

VEHICLE IDENTIFICATION NUMBER SYSTEMS

1977-02-01

HISTORICAL

J272A_197702

This recommended practice describes general characteristics of VIN systems. It includes certain specific requirements, supporting definitions, basic content, and examples.

Standard

WORLD MANUFACTURER IDENTIFIER

1977-02-01

HISTORICAL

J1044A_197702

This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853, J187, J272a, J273a, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.

Standard

TRUCK & TRUCK TRACTOR VEHICLE IDENTIFICATION NUMBER SYSTEMS

1975-01-01

HISTORICAL

J1108_197501

This recommended practice supplements SAE J272. It applies to characteristics of Truck & Tractor descriptive and identifying information which are set forth in a uniform manner in the Vehicle Identification Number (VIN).

Standard

PASSENGER CAR VEHICLE IDENTIFICATION NUMBER SYSTEM

1972-06-01

HISTORICAL

J273_197206

This practice supplements SAE J272. It applies to characteristics of passenger car descriptive and identifying information which are to be set forth in a uniform manner in the identification number.