Search Results

Standard

Accessory Drive Tensioner Test Standards

2024-04-10

WIP

J2436

Update typo from: 4.3.9 Spray frequency: (1) application per hour (Moderate Test: eight (8) applications per hour) to: 4.3.9 Spray frequency: (1) application per hour (Moderate Test: (1) application every (8) hours)

Standard

Accessory Drive Tensioner Test Standards

2023-11-15

CURRENT

J2436_202311

To document test procedures and setups that address known failure modes for Accessory Drive automatic tensioners. This SAE Standard does not encompass the pulley or pulley bearing. The sample sizes and acceptance criteria should be determined by agreement between the original equipment manufacturer (OEM) and the supplier. The failure modes to be addressed are: Test Factors include: NOTE: The Belt Drive Committee recommends that this spec be run using test parts that are close to the upper and lower specifications for load output and damping (tails testing).

Standard

V-Ribbed Belts and Pulleys

2022-05-16

CURRENT

J1459_202205

This SAE Standard covers the dimensioning technique, tolerances, and methods of measurement of V-ribbed belts and mating pulleys for use on automotive accessory drives.

Standard

Performance Testing of PK Section V-Ribbed Belts

2021-11-09

CURRENT

J2432_202111

The following information covers accessory drive belt testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. Belt construction definitions are also documented. This information has been prepared from existing literature, including standards and data supplied by producers and users of V-ribbed belts.

Standard

Glossary - Automatic Belt Tensioner

2021-09-10

CURRENT

J2198_202109

This glossary was written to provide a consistent and uniform definition of terms used in describing an automatic belt tensioner as it applies to an automotive accessory drive system.

Standard

V-Belts and Pulleys

2019-12-17

CURRENT

J636_201912

This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.

Standard

V-Belts and Pulleys

2019-10-02

HISTORICAL

J636_201910

This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.

Standard

Automotive V-Ribbed Belt Drives and Test Methods

2019-09-24

CURRENT

J1596_201909

The following information covers engine accessory drive layout details and testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. This information has been prepared from existing literature, including standards and data supplied by both producers and users of V-ribbed belts.

Standard

Accessory Drive Tensioner Test Standards

2016-07-01

HISTORICAL

J2436_201607

To document test procedures and set-ups that address known failure modes for Accessory Drive automatic tensioners This SAE Standard does not encompass the pulley or pulley bearing. The sample sizes and acceptance criteria should be determined by agreement between the original equipment manufacturer (OEM) and the supplier. The failure modes to be addressed are: Test Factors include: NOTE: The Belt Drive Committee recommends that this spec be run using test parts that are close to the upper and lower specifications for load output and damping (tails testing).

Standard

Performance Testing of PK Section V-Ribbed Belts

2015-03-13

HISTORICAL

J2432_201503

The following information covers accessory drive belt testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. Belt construction definitions are also documented. This information has been prepared from existing literature, including standards and data supplied by Producers and Users of V-ribbed belts.

Standard

Glossary - Automatic Belt Tensioner

2013-04-24

HISTORICAL

J2198_201304

This glossary was written to provide a consistent and uniform definition of terms used in describing an automatic belt tensioner as it applies to an automotive accessory drive system.

Standard

Performance Testing of PK Section V-Ribbed Belts

2012-11-19

HISTORICAL

J2432_201211

The following information covers accessory drive belt testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. Belt construction definitions are also documented. This information has been prepared from existing literature, including standards and data supplied by Producers and Users of V- ribbed belts.

Standard

V-Belts and Pulleys

2012-11-01

HISTORICAL

J636_201211

This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.

Standard

Automotive V-Belt Drives

2012-08-14

CURRENT

J637_201208

The following information is intended as a guide to be used for evaluating belt construction, source approval, and quality audit. This recommendation has been prepared from existing literature, including standards, specifications, and data supplied by both producers and users. These recommendations cover drive layout details and V-belt testing methods, including test layout, pulley diameters, torque loads, and guidance for interpreting test data. The application of these automotive V-belts is to power engine or vehicle accessories that are physically attached to the engine.

Standard

Automotive Synchronous Belt Drives

2012-08-14

CURRENT

J1313_201208

The following information applies to automotive camshaft drives, distributor drives, or other underhood drives that may require synchronization. For other power transmission drives requiring synchronization, refer to Specifications for Drives using Synchronous Belts (MXL, XL, L, H, XH and XXH belt sections) (IP 24/1978), published jointly by the Rubber Manufacturers Association (RMA), the Mechanical Power Transmission Association (MPTA), and the Rubber Association of Canada (RAC).

Standard

SI (Metric) Synchronous Belts and Pulleys

2012-07-05

CURRENT

J1278_201207

Synchronous belt drives consist of a toothed belt which mates with grooved pulleys to provide a precise speed ratio between the driver and driven pulleys. This SAE Standard covers the synchronous belt and pulley sections currently in use in automotive applications such as camshaft, distributor, and other underhood drives that may require synchronization. It also provides for future sections to be added as usage develops.

Standard

V-Ribbed Belts and Pulleys

2009-12-18

HISTORICAL

J1459_200912

This SAE Standard covers the dimensioning technique, tolerances, and methods of measurement of V-ribbed belts and mating pulleys for use on automotive accessory drives.

Standard

Automotive V-Belt Drives

2001-12-10

HISTORICAL

J637_200112

The following information is intended as a guide to be used for evaluating belt construction, source approval, and quality audit. This recommendation has been prepared from existing literature, including standards, specifications, and data supplied by both producers and users. These recommendations cover drive layout details and V-belt testing methods, including test layout, pulley diameters, torque loads, and guidance for interpreting test data. The application of these automotive V-belts is to power engine or vehicle accessories that are physically attached to the engine.

Standard

V-Belts and Pulleys

2001-12-10

HISTORICAL

J636_200112

This specification covers standard dimensions, tolerances, and methods of measurement of V-belts and pulleys for automotive V-belt drives.

Standard

V-Ribbed Belts and Pulleys

2001-09-07

HISTORICAL

J1459_200109

This SAE Standard covers the dimensioning technique, tolerances, and methods of measurement of V-ribbed belts and mating pulleys for use on automotive accessory drives.