Criteria

Text:
Display:

Results

Viewing 1 to 30 of 58
CURRENT
2016-05-10
Standard
J1668_201605
The correct setting and adjustment of fuel injection pumps requires standardized testing conditions. This SAE Standard summarizes the design and operating parameters for test benches so that, using certain information supplied by the pump manufacturer, the pump test schedule, and certain information supplied by the test bench manufacturer, it can be determined whether a particular test bench is suitable for driving a particular injection pump. This document is in most cases a summary of the ISO Standard 4008, Parts 1, 2, and 3 and is intended to provide its critical aspects. Standard ISO 4008 should be referred to for more details.
CURRENT
2015-12-17
Standard
J967_201512
This SAE Standard defines the requirements of a calibration fluid recommended for flow bench testing, calibration, and flushing of fuel injection equipment, in production facilities, in laboratories, and in service establishments.
CURRENT
2015-11-24
Standard
J1949_201511
This SAE Standard specifies the dimensional requirements for the assembly of high-pressure pipe connections for compression-ignition (diesel) engine fuel injection equipment. It applies to 60 deg female cones with external threaded connectors types 1 and 2, and to the internal threaded tube nuts and male cone type end assembly of high- pressure pipe connections for tubes with diameters up to 12 mm inclusive.
CURRENT
2015-11-24
Standard
J1419_201511
This SAE Standard specifies the dimensional requirements necessary for the interchangeability of tapered shaft ends and hubs for fuel injection pumps of diesel engines.
CURRENT
2015-11-24
Standard
J1418_201511
This SAE Standard specifies the dimensional requirement of a range of high pressure pipes for use in the bench testing and setting of fuel injection pumps. Only dimensions and requirements affecting the hydraulic characteristic of the pipes are defined. Other requirements, such as the type of end connections and shape of the pipes when bent, are not included. These depend on the connections provided at pump outlets and injector inlets, and on the design features of individual pumps and test benches.
CURRENT
2015-11-24
Standard
J1984_201511
This document specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. Field of Application This document applies to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and a 5.5 mm (nominal) nozzle body tip diameter and deals with the interface between the injector and the engine. The internal construction of the injector remains optional with the manufacturer.
CURRENT
2015-11-24
Standard
J2265_201511
This SAE Standard specifies: a test method for assessing the lubricating property of diesel fuels including those which may contain a lubricity enhancing additive, and the performance criteria necessary to ensure reliable operation of diesel fuel injection equipment with respect to fuel lubrication of such equipment. It applies to fuel used in diesel engines.
CURRENT
2015-11-24
Standard
J265_201511
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of four types of fuel injectors in diesel engines. Two of the types specified are flats-located injectors. The location and dimensions of the fuel inlet, leak-off connections, and type of attachment are not defined since they may vary according to the particular application. Field of Application This document is applicable to nozzle holder types 8 and 10 of an unspecified means of angular location and flats-located types 9 and 11 with a 17.0 mm (nominal) shank diameter. The internal construction of the fuel injector remains optional with the manufacturer.
CURRENT
2015-11-24
Standard
J347_201511
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. Field of Application This document is applicable to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and deals only with the interface between the injector and the engine. The internal construction of the fuel injector remains optional with the manufacturer.
CURRENT
2015-11-24
Standard
J629_201511
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of two types of fuel injectors in diesel engines. The location and dimensions of the fuel inlet, leak-off connections, and flange design are not defined since they may vary according to the particular application. Field of Application This document is applicable to nozzle holder types 5 and 6 of a flange mounted design with a 21.0 mm (nominal) shank diameter used with size S nozzles specified in ISO 2697. The internal construction of the fuel injector remains optional with the manufacturer.
CURRENT
2015-11-24
Standard
J626_201511
This SAE Standard specifies dimensional requirements for eight types of end-mounting flange for fuel injection pumps for use in diesel (compression ignition) engines.
CURRENT
2015-11-24
Standard
J830_201511
This SAE Standard establishes a vocabulary and definitions relating to the components used in fuel injection systems for compression ignition (diesel) engines. Definitions are separated into six sections by topic as follows: Section 3--Fuel Injection Pumps Section 4--Fuel Injectors Section 5--Unit Injectors Section 6--Governors Section 7--Timing Devices Section 8--High Pressure Pipes and Connections NOTE: When the word fuel is used in the terms listed it may be omitted providing there can be no misunderstanding.
CURRENT
2015-11-24
Standard
J1958_201511
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
CURRENT
2015-09-22
Standard
J1549_201509
The fuel injection pump is intended to validate the accuracy of calibrating nozzle and holder assemblies for applications using 0.4 - 0.8 mm diameter orifice plates and to assist in identifying problems in fuel injection pump test stands. This SAE Recommended Practice is divided into two parts: Part I—Design, Description and Specifications of the Fuel Injection Pump; and Part II—Test Procedures for Using the Fuel Injection Pump.
CURRENT
2015-09-22
Standard
J2317_201509
This SAE Recommended Practice defines a guideline for the fuel injection pump designer to select appropriate fastener designs which are considered to be tamper-resistant. It applies to fuel injection pumps used on diesel engines.
CURRENT
2015-09-22
Standard
J968/1_201509
This part of SAE J968 specifies two types of calibrating nozzle and holder assemblies intended for the testing and setting of diesel injection pumps on test benches. It applies to: A calibrating nozzle and holder assembly with a single hole orifice plate; A calibrating nozzle and holder assembly with a delay pintle type nozzle. The approximate range of the calibrating nozzle and holder assembly is up to: 300 mm3/stroke with the single hole orifice plate; 150 mm3/stroke with the delay pintle type nozzle. Setting and maintenance requirements are specified in ISO 4008/3.
CURRENT
2015-09-22
Standard
J968/2_201509
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
HISTORICAL
2002-12-20
Standard
J968/1_200212
This part of SAE J968 specifies two types of calibrating nozzle and holder assemblies intended for the testing and setting of diesel injection pumps on test benches. It applies to: A calibrating nozzle and holder assembly with a single hole orifice plate; A calibrating nozzle and holder assembly with a delay pintle type nozzle. The approximate range of the calibrating nozzle and holder assembly is up to: 300 mm3/stroke with the single hole orifice plate; 150 mm3/stroke with the delay pintle type nozzle. Setting and maintenance requirements are specified in ISO 4008/3.
HISTORICAL
2002-12-20
Standard
J968/2_200212
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
HISTORICAL
2002-12-13
Standard
J265_200212
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of four types of fuel injectors in diesel engines. Two of the types specified are flats-located injectors. The location and dimensions of the fuel inlet, leak-off connections, and type of attachment are not defined since they may vary according to the particular application.
HISTORICAL
2002-12-13
Standard
J629_200212
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of two types of fuel injectors in diesel engines. The location and dimensions of the fuel inlet, leak-off connections, and flange design are not defined since they may vary according to the particular application.
HISTORICAL
2002-10-25
Standard
J1418_200210
This SAE Standard specifies the dimensional requirement of a range of high pressure pipes for use in the bench testing and setting of fuel injection pumps. Only dimensions and requirements affecting the hydraulic characteristic of the pipes are defined. Other requirements, such as the type of end connections and shape of the pipes when bent, are not included. These depend on the connections provided at pump outlets and injector inlets, and on the design features of individual pumps and test benches.
HISTORICAL
2002-10-25
Standard
J1984_200210
This document specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines.
HISTORICAL
2002-10-25
Standard
J347_200210
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines.
HISTORICAL
2002-10-25
Standard
J1958_200210
This SAE Standard specifies dimensions and requirements for single-wall steel tubing intended for use as high-pressure fuel injection pipes on a wide range of engines (Class A), and for fuel injection pump testing (Class B, Reference SAE J1418). Tubing shall be cold drawn, annealed or normalized, seamless tubing suitable for cold swaging, cold upsetting, and cold bending.
HISTORICAL
2002-09-30
Standard
J2317_200209
This SAE Recommended Practice defines a guideline for the fuel injection pump designer to select appropriate fastener designs which are considered to be tamper-resistant. It applies to fuel injection pumps used on diesel engines.
HISTORICAL
2002-08-29
Standard
J967_200208
This SAE Standard defines the requirements of a calibration fluid recommended for flow bench testing, calibration, and flushing of fuel injection equipment, in production facilities, in laboratories, and in service establishments.
HISTORICAL
1999-04-21
Standard
J830_199904
This SAE Standard establishes a vocabulary and definitions relating to the components used in fuel injection systems for compression ignition (diesel) engines. Definitions are separated into six sections by topic as follows: Section 3— Fuel Injection Pumps Section 4— Fuel Injectors Section 5— Unit Injectors Section 6— Governors Section 7— Timing Devices Section 8— High Pressure Pipes and Connections NOTE— When the word "fuel" is used in the terms listed it may be omitted providing there can be no misunderstanding.
HISTORICAL
1999-04-16
Standard
J1668_199904
The correct setting and adjustment of fuel injection pumps requires standardized testing conditions. This SAE Standard summarizes the design and operating parameters for test benches so that, using certain information supplied by the pump manufacturer, the pump test schedule, and certain information supplied by the test bench manufacturer, it can be determined whether a particular test bench is suitable for driving a particular injection pump. This document is in most cases a summary of the ISO Standard 4008, Parts 1, 2, and 3 and is intended to provide its critical aspects. Standard ISO 4008 should be referred to for more details.
HISTORICAL
1999-04-01
Standard
J1419_199904
This SAE Standard specifies the dimensional requirements necessary for the interchangeability of tapered shaft ends and hubs for fuel injection pumps of diesel engines.
Viewing 1 to 30 of 58