Refine Your Search

Search Results

Standard

Seat Belt Restraint System Hardware - Glossary of Terms

2018-03-16
WIP
J1803
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
Standard

Seat Belt Hardware Test Procedures

2018-03-02
WIP
J140
This SAE Recommended Practice describes test procedures for evaluating hardware used in motor vehicle seat belt assemblies. Related hardware performance requirements are described in SAE J141. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.
Standard

Seat Belt Hardware Performance Requirements

2018-03-02
WIP
J141
This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.
Standard

Motor Vehicle Seat Belt Anchorages - Design Recommendations

2014-10-28
CURRENT
J383_201410
This SAE Recommended Practice specifies design recommendations for the location of seat belt assembly anchorages which will promote proper transfer of occupant restraint forces on the strongest parts of the human anatomy to the vehicle or seat structure. Test procedures are specified in SAE J384.
Standard

Motor Vehicle Seat Belt Anchorages - Test Procedure

2014-10-28
CURRENT
J384_201410
This SAE Recommended Practice specifies performance requirements and test procedures for the strength and location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle body structure or to seat assemblies in the vehicle. Design Considerations are specified in SAE J383.
Standard

Motor Vehicle Seat Belt Anchorages - Performance Requirements

2014-07-02
CURRENT
J385_201407
This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384, respectively.
Standard

Seat Belt Hardware Webbing Abrasion Test Procedure

2013-06-11
CURRENT
J339_201306
This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in hardware of seat belt assemblies such as those described in SAE J140.
Standard

Seat Belt Hardware Webbing Abrasion Performance Requirements

2013-06-11
CURRENT
J114_201306
This SAE Recommended Practice describes the performance requirements for abrasion resistance of webbing when used in adjustment hardware normally used to adjust the length of seat belt assemblies such as those described in SAE J140. These requirements are applicable to tests conducted according to the procedure described in SAE J339. Although adjustment hardware is normally the primary source of webbing abrasion in a seat belt assembly, consideration should be given to other areas of normal webbing contact in the restraint system that may provide a more severe condition of webbing abrasion.
Standard

Motor Vehicle Seat Belt Anchorages - Performance Requirements

2013-03-28
HISTORICAL
J385_201303
This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384, respectively.
Standard

Motor Vehicle Seat Belt Anchorages - Design Recommendations

2013-03-28
HISTORICAL
J383_201303
This SAE Recommended Practice specifies design recommendations for location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle structure or installed to seat assemblies in the vehicle. (This SAE Recommended Practice supersedes the Design Section of SAE J787b). Performance requirements and test procedures are specified in SAE J385 and SAE J384, respectively.
Standard

Motor Vehicle Seat Belt Anchorages - Test Procedure

2013-03-28
HISTORICAL
J384_201303
This SAE Recommended Practice outlines static test procedure for the evaluation of the performance of seat belt anchorages attached to vehicle structure or to seat assemblies installed in the vehicle. (This SAE Recommended Practice supersedes the Test Procedure Section of SAE 787b.) Design recommendations and performance requirements are specified in the Recommended Practices SAE J383 and SAE J385, respectively.
Standard

Seat Belt Hardware Test Procedures

2013-02-13
CURRENT
J140_201302
This SAE Recommended Practice describes test procedures for evaluating hardware used in motor vehicle seat belt assemblies. Related hardware performance requirements are described in SAE J141. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.
Standard

Seat Belt Hardware Performance Requirements

2013-02-13
CURRENT
J141_201302
This SAE Recommended Practice describes performance requirements for hardware used in motor vehicle seat belt assemblies when tested in accordance with the test procedures specified in SAE J140. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.
Standard

Seat Belt Restraint System Hardware - Glossary of Terms

2013-01-08
CURRENT
J1803_201301
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
Standard

Recommended Design and Performance Standard for Seats with Integrated Lap and Shoulder Restraints

2012-09-12
CURRENT
J2287_201209
This SAE Recommended Practice defines minimum performance standards, qualification requirements, and minimum documentation requirements for Integrated Lap and Shoulder Restraint (to) equipped Seats (IL&SRTS). The goal is to achieve comfort, durability, and occupant protection under expected and foreseeable normal operation loads. The document attempts to define test and evaluation criteria to demonstrate performance at peak operational loads, while attempting to maintain the seat’s ability to meet loads set forth in FMVSS 207, 210, and ECE 14, 16, and 17. This document also provides guidance for design by enumerating certain design goals to enhance comfort, serviceability, and safety. Guidance for test procedures, measurements, equipment, and interpretation of results may be presented to promote uniform techniques and to achieve acceptable data.
Standard

Seat Belt Restraint Systems Hardware - Glossary of Terms

2011-04-06
HISTORICAL
J1803_201104
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
Standard

Motor Vehicle Seat Belt Assembly Installation

2009-02-25
CURRENT
J800_200902
This SAE Recommended Practice provides general installation instructions for aftermarket, universal type seat belt assemblies for installation in passenger cars, trucks, buses, and multipurpose passenger vehicles. This SAE document is intended to provide guidance in the installation of seat belt assemblies meeting the requirements of Part 571.209 of Title 49 of the Code of Federal Regulations as established by the National Highway Traffic Safety Administration.
Standard

Recommended Design and Performance Standard for Seats With Integrated Lap and Shoulder Restraints

1999-04-01
HISTORICAL
J2287_199904
This SAE Recommended Practice defines minimum performance standards, qualification requirements, and minimum documentation requirements for Integrated Lap and Shoulder Restraint (to) equipped Seats (IL&SRTS). The goal is to achieve comfort, durability, and occupant protection under expected and foreseeable normal operation loads. The document attempts to define test and evaluation criteria to demonstrate performance at peak operational loads, while attempting to maintain the seat's ability to meet loads set forth in FMVSS 207, 210, and ECE 14, 16, and 17. This document also provides guidance for design by enumerating certain design goals to enhance comfort, serviceability, and safety. Guidance for test procedures, measurements, equipment, and interpretation of results may be presented to promote uniform techniques and to achieve acceptable data.
Standard

Seat Belt Restraint Systems Hardware-Glossary of Terms

1997-04-01
HISTORICAL
J1803_199704
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
Standard

Motor Vehicle Seat Belt Anchorages--Design Recommendations

1995-06-01
HISTORICAL
J383_199506
This SAE Recommended Practice specifies design recommendations for location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle structure or installed to seat assemblies in the vehicle. (This SAE Recommended Practice supersedes the Design Section of SAE J787b). Performance requirements and test procedures are specified in SAE J385 and SAE J384, respectively.
X