Refine Your Search

Search Results

Standard

Automotive Gear Lubricants for Commercial and Military Use

2019-01-07
CURRENT
J2360_201901
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).
Standard

Automotive Gear Lubricant Viscosity Classification

2017-08-14
HISTORICAL
J306_201708
This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered.
Standard

Fluid for Passenger Car Type Automatic Transmissions

2016-08-23
WIP
J311
This SAE Information Report details some of the equipment and procedures used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It is intended to assist those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for the use in passenger car and light-duty truck automatic transmissions. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automatic transmission fluids.
Standard

Axle and Manual Transmission Lubricants

2013-06-20
WIP
J308
This SAE Information Report was prepared by the SAE Fuels and Lubricants Technical Committee for two purposes: (a) to assist the users of automotive equipment in the selection of axle and manual transmission lubricants for field use, and (b) to promote a uniform practice for use by marketers of lubricants and by equipment builders in identifying and recommending these lubricants by a service designation.
Standard

Automotive Lubricating Greases

2012-09-05
WIP
J310
This SAE Recommended Practice was developed by SAE, and the section ÒStandard Classification and Specification for Service GreasesÓ cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases.
Standard

Heavy Duty Vehicle Lubricating Greases

2012-09-05
WIP
J2695
This SAE Recommended Practice was developed by SAE, and the section "Standard Classification and Specification for Service Greases" cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of heavy duty vehicle components, and with the selection and marketing of greases for the lubrication of certain of those components on heavy duty vehicles like trucks and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of heavy duty vehicle greases.
Standard

Automotive Gear Lubricants for Commercial and Military Use

2012-04-25
HISTORICAL
J2360_201204
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).
Standard

Lubricant Types--Construction and Industrial Machinery

2009-09-28
CURRENT
J754_200909
This SAE Information Report is an introduction to lubricant classifications, specifications, and types in common use today. It emphasizes the desirability of using a minimum number of lubricants. Pertinent SAE reports are called out for easy reference. Lubricant abbreviations have been included that will assist in preparation of lubrication charts (described in SAE J753). Table 1 lists the components of construction and industrial equipment and the various lubricants which may be used. Table 2 lists lubricant types and identifying abbreviations. Lubricants that had common usage in the past are retained in Table 2 to show where the new specifications originated.
Standard

Axle and Manual Transmission Lubricants

2007-03-22
CURRENT
J308_200703
This SAE Information Report was prepared by the SAE Fuels and Lubricants Technical Committee for two purposes: (a) to assist the users of automotive equipment in the selection of axle1 and manual transmission lubricants for field use, and (b) to promote a uniform practice for use by marketers of lubricants and by equipment builders in identifying and recommending these lubricants by a service designation.
Standard

Heavy Duty Vehicle Lubricating Greases

2005-08-11
CURRENT
J2695_200508
This SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of heavy duty vehicle components, and with the selection and marketing of greases for the lubrication of certain of those components on heavy duty vehicles like trucks and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of heavy duty vehicle greases.
Standard

Automotive Lubricating Greases

2005-07-14
CURRENT
J310_200507
This SAE Recommended Practice was developed by SAE, and the section “Standard Classification and Specification for Service Greases” cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases.
Standard

Automotive Gear Lubricant Viscosity Classification

2005-06-14
HISTORICAL
J306_200506
This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered.
Standard

Fluid for Passenger Car Type Automatic Transmissions

2000-02-22
CURRENT
J311_200002
This SAE Information Report details some of the equipment and procedures used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It is intended to assist those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for the use in passenger car and light-duty truck automatic transmissions. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automatic transmission fluids.
Standard

Automotive Lubricating Greases*HS-23/00*

2000-01-20
HISTORICAL
J310_200001
This SAE Recommended Practice was developed by SAE, and the section ÒStandard Classification and Specification for Service GreasesÓ cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases.
Standard

Powershift Transmission Fluid Classification

1999-12-17
CURRENT
J1285_199912
This SAE Recommended Practice was prepared by the SAE Fuels and Lubricants Technical Committee: (a) to assist the designers and users of heavy-duty transmissions in the selection of powershift transmission fluids for field use and (b) to promote a uniform practice for use by marketers of lubricants and equipment builders in identifying and recommending these fluids by type. This classification is designed for fluids used in heavy-duty truck, bus, earthmoving, and marine transmissions or steering clutches. The fluids must perform the following five functions: 1. Transmit hydrodynamic energy in a torque converter. 2. Transmit hydrostatic energy in hydraulic circuits. 3. Lubricate bearings, bushings, gears, and moving parts. 4. Provide proper frictional properties in lubricated bands and clutches. 5. Provide heat transfer medium for liquid- or air-cooled systems to maintain suitable operational temperature range.
Standard

Automotive Gear Lubricant Viscosity Classification

1998-07-01
HISTORICAL
J306_199807
This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered.
Standard

Automotive Lubricating Greases

1997-05-01
HISTORICAL
J310_199705
This SAE Recommended Practice was developed by SAE, and the section 'Standard Classification and Specification for Service Greases' cooperatively with ASTM, and NLGI. It is intended to assist those concerned with the design of automotive components, and with the selection and marketing of greases for the lubrication of certain of those components on passenger cars, trucks, and buses. The information contained herein will be helpful in understanding the terms related to properties, designations, and service applications of automotive greases.
Standard

Axle and Manual Transmission Lubricants

1996-01-01
HISTORICAL
J308_199601
This SAE Information Report was prepared by the SAE Fuels and Lubricants Technical Committee for two purposes: (a) to assist the users of automotive equipment in the selection of axle and manual transmission lubricants for field use, and (b) to promote a uniform practice for use by marketers of lubricants and by equipment builders in identifying and recommending these lubricants by a service designation.
X