Search Results

This specification sheet establishes requirements for a high collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than 7 µm when designed and tested in accordance with SAE J2321 and this specification sheet.

This SAE Standard identifies the material and dimensional requirements for component connector tubes and related items for use in fluid power components. Connector tubes are also identified as quills, ferrules or transfer tubes. Connector tubes are used to connect fluid passages within a component or to connect one component to another; for example, connecting control valves to subplates. Related items include plugs, undrilled connector tubes and connector tubes for internal check valves and restrictors.

1. Scope. 1.1 This Recommended Practice defines a procedure, which will aid in assessing the contaminant sensitivity of hydraulic components. This procedure utilizes a very high level of contaminant that permits an accelerated test to determine the affects of contamination in a relatively short period. This recommended practice utilizes the contamination sensitivity test circuit and contaminants identified in SAE J2470. 1.2 This procedure does not establish contamination sensitivity requirements for any hydraulic component. The user of this procedure needs to be aware of the system contamination level that the component will operate in and select test contamination levels significantly higher that the operating level in order to assess the suitability of the component.

This SAE Recommended Practice defines a procedure, which will aid in assessing the contaminant sensitivity of hydraulic valves. The approach taken defines a test procedure with flexibility for testing valves in a wide range of contamination levels. The user of this procedure must establish the contamination levels for testing. Three levels are suggested which should cover the range for most valve applications. This procedure does not establish the contaminant sensitivity requirements for any valve. The user of this procedure needs to be aware of the system contamination level that the valve will operate in and select test contamination levels significantly higher than the operating level to assess the suitability of the valve. The test procedure permits a valve to be tested without disassembly and therefore permits protection of proprietary design information. This procedure assesses the contamination sensitivity of valves by contaminant lock.

This Information Report provides a description of bleed-air pneumatic system elements and identifies parameters required to define the requirements for a detailed specification. Specific design requirements are dependent on the application and should be incorporated in a detailed specification.

The marine environment differs greatly from other environments in which hydraulics are used. This Recommended Practice provides hydraulic design considerations and criteria for the marine environment and is applicable to commercial vessels, military ships, and submersible vehicles. This document may be used for manned and un-manned vehicles.

This SAE Recommended Practice provides the designer with guidance for the selection of directional control valves for use in the hydraulic systems of surface ships and submersibles. This guidance includes use of standard valves and interfaces, minimum envelopes that should be reserved to permit interchangeability, environmental considerations, and general technical requirements.

This SAE Recommended Practice provides guidance for defining the requirements for evaluating hydraulic pumps and motors and for preparing detailed specifications for these components. The user can follow this document to set forth the pump and motor environmental and performance considerations, establish service life and reliability goals, and define specific evaluation tests for marine vehicle applications.

This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.

This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic systems filters, their locations within the system and the dirt capacity of the filter elements. This document is generally applicable to all ship hydraulic systems but does not apply to personal or recreational watercraft.

Hydraulic systems are used on marine vehicles for steering, vehicle control, and utility services. System components that generate and transmit noise are of concern. This SAE Information Report (a) addresses noise requirements which may apply to the hydraulic systems of ships and submersibles, and (b) identifies noise sources and techniques which may be used to reduce system noise. Noise of power sources (e.g., electric motors) and end items (e.g., steering linkages) is beyond the scope of this document.

This SAE Recommended Practice provides the designer with guidance for the selection of directional control valves for use in the hydraulic systems of surface ships and submersibles. This guidance includes use of standard valves and interfaces, minimum envelopes that should be reserved to permit interchangeability, environmental considerations, and general technical requirements.

This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic system filters, their locations within the system and the dirt capacity of the filter elements.

This specification sheet establishes requirements for high collapse pressure configuration filter elements of several configurations with a minimum filtration ratio of 75 for particles larger than 10 µm when designed and tested in accordance with SAE J2321 and this specification sheet.

This specification sheet establishes requirements for low collapse pressure elements of a specific configuration with various efficiency ratings designed and tested in accordance with SAE J2321 and the requirements of this specification sheet.

This specification sheet establishes requirements for a high collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than 7 µm when designed and tested in accordance with SAE J2321 and this specification sheet.

The scope of this Recommended Practice is to delineate groups of materials for which there is considerable fabrication and operating experience in the sea water environment. In addition, some of the more promising materials for possible future applications are covered.

This HIR provides a description of bleed-air pneumatic system elements and identifies parameters required to define the requirements for a detailed specification. Specific design requirements are dependent on the application and should be incorporated in a detailed specification.

The marine environment differs greatly from other environments in which hydraulics are used. This Recommended Practice provides hydraulic design considerations and criteria for the marine environment and is applicable to commercial vessels, military ships, and submersible vehicles. This document may be used for manned and un-manned vehicles.

This specification sheet establishes requirements for a low collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than ? μm when designed and tested in accordance with SAE J2321 and this specification sheet. Note: The efficiency and dirt capacity have not yet been determined..