Search Results

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917.

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

This SAE Standard specifies basic tolerances and dimensions for inboard propeller-shaft ends, propeller hubs and keyways for shaft sizes 3/4 in (19 mm) through 8 in (203 mm).

This SAE Recommended Practice establishes the procedure for measuring the maximum exterior sound level of recreational motorboats while being operated under a variety of operating conditions. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

This method covers electric outboards that are rated in terms of static thrust.

This SAE Recommended Practice covers all electrical devices suitable for use in marine engine compartments and fuel tank spaces.

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

This SAE Standard covers dimensions, performance parameters, and nomenclature of a push-pull control cable used in outboard, inboard, and sterndrive marine throttle and shift applications.

This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull.

It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.

This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.

This SAE Recommended Practice covers the requirements for switches used in marine applications both under and over 50 V.

This SAE Recommended Practice establishes the procedure for determining if recreational motorboats have effective exhaust muffling means when operating in the stationary mode. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

This SAE Recommended Practice establishes the procedure for measuring the maximum exterior sound level of recreational motorboats while being operated under a variety of operating conditions. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

This SAE Standard covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from within the gasoline engine to the surrounding atmosphere.

This SAE Recommended Practice establishes the procedure for measuring the sound level of recreational motorboats in the vicinity of a shore bordering any recreational boating area during which time a boat is operating under conditions other than stationary mode operation. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

This Standard covers the requirements for all marine inboard and outboard gasoline engine ignition assemblies and components.

This SAE Recommended Practice covers the requirements for all marine inboard engine wiring, wiring assemblies, wiring components, and wiring connectors connected to microprocessors associated with the operation of the propulsion system, operating at 50 V or less. EXCEPTION—Outboard engines and engines in Personal Water Craft (PWC). NOTE: See ABYC E11 for additional requirements related to electrical installations on small craft.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine hydraulic transmissions where push-pull cable control is applicable. For control cable information see SAE J917.

The purpose of this SAE Recommended Practice is to provide guides toward standard conditions for operating marine engine throttles (gasoline or diesel) where push-pull cable control is applicable. For control cable information see SAE J917.