Refine Your Search

Topic

Search Results

Standard

Test Procedure for Parking Stability of Motorcycles

2020-09-09
CURRENT
J1101_202009
Side stands and center stands are designed to support stationary two-wheel motorcycles. This SAE Standard establishes procedures for determining parking surface loading and stability limits as follows: a The footprint pressure exerted on a horizontal parking surface by the stand. b The tilt angle of the parking surface at which tip-over occurs. c The tilt angle of the parking surface at which roll-off occurs.
Standard

Measurement of Exhaust Sound Pressure Levels of Stationary On-Highway Motorcycles

2020-07-17
CURRENT
J2825_202007
This SAE Recommended Practice establishes test procedures, test conditions, environment, and instrumentation for determining the exhaust sound pressure levels of stationary motorcycles. These are based on a comprehensive study of a wide variety of on-highway motorcycles, and therefore are intended to be applied to on-highway motorcycles. For off-highway motorcycles, SAE J1287 continues to be the recommended practice.
Standard

Sound Levels for Motorcycles

2020-07-17
CURRENT
J331_202007
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the sound levels of motorcycles under full throttle acceleration and closed throttle deceleration.
Standard

Maximum Sound Level Potential for Motorcycles

2020-06-05
CURRENT
J47_202006
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the maximum sound level potential for motorcycles under wide open throttle acceleration and closed throttle deceleration.
Standard

Motorcycle Classifications

2020-02-05
WIP
J213
This SAE Recommended Practice provides uniform definitions and classifications for motorcycles.
Standard

Riding Range Test Procedure for On-Highway Electric Motorcycles

2019-12-17
WIP
J2982
This SAE Recommended Practice incorporates dynamometer test procedures that produce riding range estimates for electric motorcycles during stop-and-go urban riding on surface streets and commuting trips in urban areas that include operation on freeways.
Standard

Top Speed Test Procedure for Electric Motorcycles

2019-12-17
WIP
J3007
This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.
Standard

Motorcycle Terminology

2019-09-24
CURRENT
J3133_201909
The motorcycle terminology presented herein addresses two-wheel single track vehicles, as well as motorized three wheel cycles. Although two-wheeled, single track scooters and mopeds are similar to traditional motorcycles, they have many characteristics which differentiate them from motorcycles, and while some terms will apply, this Terminology addresses motorcycles specifically, unless otherwise noted. Likewise, some three wheel cycles may have some similar design features and share components with motorcycle, the dynamics and handling of three wheel vehicles differs from two wheel, single track motorcycles.
Standard

Operator Controls and Displays on Motorcycles

2019-08-28
CURRENT
J107_201908
This SAE Recommended Practice applies to two- and three-wheel motorcycles intended for highway use. Vehicles commonly known as mopeds and mini-bikes are included in this vehicle category if they are intended for highway use.
Standard

Measurement of Exhaust Sound Pressure Levels of Stationary Motorcycles

2017-04-28
CURRENT
J1287_201704
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the exhaust sound pressure levels of motorcycles under stationary conditions. Since initial publication, it has been successfully applied to regulation and monitoring of sound pressure levels of off-highway vehicles, and that remains its recommended application. Users of SAE J1287 for the purpose of roadside enforcement of sound pressure levels for on-highway motorcycles have reported difficulties with its implementation in that application. In response, SAE J2825 was developed, and is recommended for measurement of exhaust sound pressure levels of stationary on-highway motorcycles. Care must be taken not to confuse stationary sound pressure levels with total motorcycle sound pressure levels. This test does not evaluate total motorcycle sound during operation. For this purpose, SAE J331 or SAE J47 is recommended.
Standard

Rear View Mirrors - Motorcycles

2016-08-03
CURRENT
J268_201608
This SAE Recommended Practice specifies recommendations for rear view mirror systems to provide the operator with a clear view to the rear. It is intended as a supplement to the requirements for motorcycle mirrors given in 49 CFR 571.111.
Standard

Fuel and Lubricant Tanks for Motorcycles

2015-10-14
WIP
J1241
This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered.
Standard

Characterizing a Test Surface for Motorcycle Side Stand Retraction Performance Testing

2014-10-24
CURRENT
J1846_201410
This SAE Recommended Practice is intended for use only in characterizing test surfaces used in motorcycle side stand retraction testing (SAE J1578). The equipment and procedure described in this document yields repeatable results in characterizing test surfaces in a way found to be related to retraction performance. The test results obtained with this procedure do not necessarily correlate with measurements obtained with other friction measurement procedures which have been developed for other purposes.
X