Refine Your Search

Topic

Search Results

Standard

Florida Exposure of Automotive Finishes

2013-11-13
CURRENT
J951_201311
The purpose of this SAE Information Report is to compare the results of Florida exposure at 45 deg from the horizontal, facing south, with those at deg from the horizontal, facing south, using various types and colors of automotive finishes.
Standard

Synthetic Resin Plastic Sealers, Nondrying Type

2013-07-09
CURRENT
J250_201307
The material desired under this recommended practice is a synthetic resin plastic sealer of the nondrying, nonbleeding, and noncorrosive type that may be extruded to the specified size and used as a medium for producing a water tight seal between 2 pressed steel sections or between rubber and steel.
Standard

Method for Evaluating the Paintable Characteristics of Automotive Sealers

2013-07-09
CURRENT
J1800_201307
This SAE Recommended Practice sets forth a method for testing and evaluating the paintable characteristics of automotive sealers. This document contains three samples preparation procedures: Method #1: Topcoat over cured primer and cured sealer Method #2: Topcoat over cured sealer Method #3: Topcoat over uncured sealer
Standard

Method of Viscosity Test for Automotive Type Adhesives, Sealers, and Deadeners

2011-12-13
WIP
J1524
This SAE Recommended Practice contains a series of test methods for use in measuring the viscosity of automotive-type adhesives, sealers, and deadeners. The test methods which are contained in this document are as follows: Brookfield Method; Castor-Severs Rheometer or Pressure Flowmeter; Penetrometer, Capillary Rheometer and Plate Rheometers.
Standard

Methods of Tests for Automotive-Type Sealers, Adhesives, and Deadeners

2011-12-13
WIP
J243
This SAE Recommended Practice contains a series of test methods for use in measuring characteristics of automotive- type sealers, adhesives, and deadeners. The test methods which are contained in this document are as follows: ADS-1—Methods of Determining Viscosity ADS-2—Low Temperature Tests ADS-3—Weld-Through Tests ADS-4—Enamel, Lacquer, and Fabric Staining Test ADS-5—Wash-Off Resistance Test ADS-7—Solids Test ADS-8—Flash Point Test ADS-9—Sag and Bridging Tests ADS-10—Flow Test The intent of this document is to provide a series of test methods which can be used in testing the various qualities of sealers, adhesives, and deadener material. In later revisions of this document, attempts will be made to reduce the number of tests now presented. The specific temperatures and times at which some of these tests are to be conducted are not dictated in these test procedures, but they will be found in the material standards which govern each type of material to be tested.
Standard

Lead-Free Replacement Paints

2001-12-11
CURRENT
J1437_200112
The purpose of this SAE Recommended Practice is to establish recommended lead-free paint color offsets to two specific color standards currently based on lead-containing pigments. The colors are identified throughout the industry as 'School Bus Yellow' and 'Highway Orange.'
Standard

PEEL STRENGTH OF SOFT TRIM ADHESIVES

1994-04-21
CURRENT
J1679_199404
This SAE Recommended Practice shall be used to determine the peel strength achieved by an adhesive when used to bond various decorative, flexible substrates such as cloth supported vinyl or carpet, to rigid (steel), semi-rigid (SMC plastic), or other similar substrates.
Standard

SOFTENING POINT OF INTERIOR TRIM ADHESIVES

1994-04-21
CURRENT
J1700_199404
This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.
Standard

COACH JOINT FRACTURE TEST

1993-11-01
CURRENT
J1863_199311
This SAE Recommended Practice defines a procedure for determining the cleavage strength of an adhesive used for bonding automotive oily metal substrates.
X