Search Results

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2001-03-12

HISTORICAL

J1102M_200103

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR WHEEL BOLTS

1974-10-01

HISTORICAL

J1102_197410

This SAE Standard covers the chemical, metallurgical and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: (a) Nonserrated shank bolts which are heat treated (b) Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18

CURRENT

J1102M_201611

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Wheel Bolts

2013-04-11

HISTORICAL

J1102_201304

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR WHEEL BOLTS

1995-02-01

HISTORICAL

J1102_199502

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21

CURRENT

J1102_201611

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2016-11-18

CURRENT

J1053M_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2013-04-11

HISTORICAL

J1053M_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN

1973-08-01

HISTORICAL

J1053_197308

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. It should be noted that stamped nuts having other sizes and configurations are available and manufacturers should be consulted.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2016-11-18

CURRENT

J1053_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

SURFACE DISCONTINUITIES ON GENERAL APPLICATION BOLTS, SCREWS, AND STUDS

1975-07-01

HISTORICAL

J1061A_197507

This recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in. diameter inclusive with lengths to 150 mm or 6 in. inclusive, having specified minimum tensile strengths of 900 MPa or 120,000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN—INCH SERIES

1996-08-01

HISTORICAL

J1053_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2013-04-11

HISTORICAL

J1053_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Surface Discontinuities on General Application Bolts, Screws, and Studs

2008-02-22

HISTORICAL

J1061_200802

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

Surface Discontinuities on General Application Bolts, Screws, and Studs

2012-11-19

CURRENT

J1061_201211

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

SURFACE DISCONTINUITIES ON GENERAL APPLICATION BOLTS, SCREWS, AND STUDS

1992-10-01

HISTORICAL

J1061_199210

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

Surface Discontinuities on General Application Bolts, Screws, and Studs

1998-05-01

HISTORICAL

J1061_199805

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

Tension Indicating Washer Tightening Method for Fasteners

2018-04-24

CURRENT

J2486_201804

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

Tension Indicating Washer Tightening Method for Fasteners

2013-04-15

HISTORICAL

J2486_201304

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.

Standard

Tension Indicating Washer Tightening Method for Fasteners

1999-05-01

HISTORICAL

J2486_199905

This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.