Search Results

Standard

Metric Thread Rolling Screws

2017-09-07

HISTORICAL

J1237_201709

This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.

Standard

Metric Thread Rolling Screws

1996-08-01

HISTORICAL

J1237_199608

This SAE Standard covers requirements for metric thread rolling screws suitable for use in general engineering applications.

Standard

Metric Thread Rolling Screws

2001-03-12

HISTORICAL

J1237_200103

This SAE Standard covers requirements for metric thread rolling screws suitable for use in general engineering applications.

Standard

NUT AND CONICAL SPRING WASHER ASSEMBLIES

1998-05-01

HISTORICAL

J238_199805

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

Nut and Conical Spring Washer Assemblies

2013-04-15

HISTORICAL

J238_201304

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

Nut and Conical Spring Washer Assemblies

2017-05-30

CURRENT

J238_201705

This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.

Standard

PROTECTIVE COATINGS FOR FASTENERS

1996-08-01

HISTORICAL

J1648_199608

This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.

Standard

PUSH-ON SPRING NUTS INCH SERIES—GENERAL SPECIFICATIONS

1996-08-01

HISTORICAL

J892_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Standard

PUSH-ON SPRING NUTS METRIC SERIES—GENERAL SPECIFICATIONS

1996-08-01

HISTORICAL

J892M_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

Plain Washers

1990-01-01

CURRENT

J488_199001

Not available.

Standard

Protective Coatings for Fasteners

2019-10-07

CURRENT

J1648_201910

This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.

Standard

Protective Coatings for Fasteners

2013-04-15

HISTORICAL

J1648_201304

This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.

Standard

Push-On Spring Nuts Inch Series - General Specifications

2016-11-23

CURRENT

J892_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Standard

Push-On Spring Nuts Inch Series - General Specifications

2013-04-16

HISTORICAL

J892_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.

Standard

Push-On Spring Nuts Metric Series - General Specifications

2013-04-16

HISTORICAL

J892M_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

Push-On Spring Nuts Metric Series - General Specifications

2016-11-21

CURRENT

J892M_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.

Standard

RIVETS AND RIVETING

1968-05-01

HISTORICAL

J492_196805

Standard

ROD ENDS AND CLEVIS PINS

1961-06-01

HISTORICAL

J493_196106

Standard

Rod Ends and Clevis Pins

2013-02-25

CURRENT

J493_201302

Standard

Round Head Bolts

1990-01-01

CURRENT

J481_199001

Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.