Search Results

Standard

TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS—INCH SERIES

1998-05-01

HISTORICAL

J174_199805

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.

Standard

TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS—METRIC SERIES

1998-05-01

HISTORICAL

J174M_199805

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2013-04-11

HISTORICAL

J174M_201304

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED THREADED FASTENERS

1983-08-01

HISTORICAL

J121_198308

This recommended practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1996-08-01

HISTORICAL

J121M_199608

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1997-04-01

HISTORICAL

J121M_199704

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

Decarburization in Hardened and Tempered Metric Threaded Fasteners

2013-01-02

CURRENT

J121M_201301

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED UNIFIED THREADED FASTENERS

1997-04-01

HISTORICAL

J121_199704

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED UNIFIED THREADED FASTENERS

1996-08-01

HISTORICAL

J121_199608

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED UNIFIED THREADED FASTENERS

1996-05-01

HISTORICAL

J121_199605

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED UNIFIED THREADED FASTENERS

1994-05-01

HISTORICAL

J121_199405

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1994-05-26

HISTORICAL

J121M_199405

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED THREADED FASTENERS

1976-07-01

HISTORICAL

J121A_197607

This recommended practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

Blind Rivets - Break Mandrel Type

2017-01-04

CURRENT

J1200_201701

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Blind Rivets—Break Mandrel Type

1998-05-01

HISTORICAL

J1200_199805

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Blind Rivets - Break Mandrel Type

2013-04-15

HISTORICAL

J1200_201304

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Decarburization in Hardened and Tempered Unified Threaded Fasteners

2013-01-02

CURRENT

J121_201301

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

Surface Discontinuities on Nuts

1998-05-01

HISTORICAL

J122_199805

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.

Standard

Surface Discontinuities on Nuts

2017-01-04

CURRENT

J122_201701

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2013-04-11

HISTORICAL

J1102M_201304

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened