Search Results

Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2011-09-08

HISTORICAL

J429_201109

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.

Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

1999-01-01

HISTORICAL

J429_199901

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.

Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

1998-05-01

HISTORICAL

J429_199805

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.

Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2014-05-07

CURRENT

J429_201405

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.

Standard

Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners

2001-03-12

HISTORICAL

J1199_200103

This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications.

Standard

Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners

2013-02-18

CURRENT

J1199_201302

This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications.

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2013-04-11

HISTORICAL

J1102M_201304

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2001-03-12

HISTORICAL

J1102M_200103

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18

CURRENT

J1102M_201611

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Steel Nuts

2021-02-08

WIP

J995

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Material Requirements for Steel Nuts

1999-07-01

HISTORICAL

J995_199907

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of ASME B18.2.2 or ASME B18.6.3, as applicable.

Standard

Mechanical and Material Requirements for Steel Nuts

2012-02-21

HISTORICAL

J995_201202

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Material Requirements for Steel Nuts

2017-07-20

CURRENT

J995_201707

This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”

Standard

Mechanical and Material Requirements for Wheel Bolts

2013-04-11

HISTORICAL

J1102_201304

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21

CURRENT

J1102_201611

This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened

Standard

Mechanical and Quality Requirements for Machine Screws

2013-01-08

CURRENT

J82_201301

This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3.

Standard

Mechanical and Quality Requirements for Tapping Screws

1998-05-01

HISTORICAL

J933_199805

This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in SAE J478.)

Standard

Mechanical and Quality Requirements for Tapping Screws

2005-08-29

HISTORICAL

J933_200508

This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, ‘Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws’.)

Standard

Mechanical and Quality Requirements for Tapping Screws

2013-02-25

CURRENT

J933_201302

This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws’.)

Standard

Metric Thread Rolling Screws

2021-11-09

CURRENT

J1237_202111

This SAE Standard covers material, dimensional, performance, and test requirements for metric thread rolling screws suitable for use in general engineering applications.