Refine Your Search

Date

Date

Topic

Topic

Search Results

Viewing 41 to 60 of 185
<< First< Previous12345Next >Last >>
Sort by relevance
Standard

Hexagon High Nuts
2016-11-18
CURRENT
J482_201611
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

HOLES IN BOLT AND SCREW SHANKS AND SLOTS IN NUTS FOR COTTER PINS
1998-05-01
HISTORICAL
J485_199805
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins
2013-04-16
HISTORICAL
J485_201304
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

HEXAGON HIGH NUTS
1998-05-01
HISTORICAL
J482_199805
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Hexagon High Nuts
2006-04-17
HISTORICAL
J482_200604
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Hexagon High Nuts
2013-04-15
HISTORICAL
J482_201304
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Standard

Thread Rolling Screws
2012-07-05
CURRENT
J81_201207
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) NOTE—The performance requirements covered in this document apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Thread Rolling Screws
1997-09-01
HISTORICAL
J81_199709
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.)
Standard

THREAD ROLLING SCREWS
1972-07-01
HISTORICAL
J81_197207
This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that “thread rolling” screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

THREAD ROLLING SCREWS
1979-06-01
HISTORICAL
J81_197906
This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Flanged 12-Point Screws
2020-08-27
WIP
J58
Included in this SAE Standard are the detailed general and dimensional specifications applicable to flanged 12-point screws recognized as SAE Standard and intended for general use in automotive and other ground-based vehicles and industrial equipment. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers should consult manufacturers concerning availability of product.
Standard

FLANGED 12-POINT SCREWS
1998-05-01
HISTORICAL
J58_199805
Included in this SAE Standard are the detailed general and dimensional specifications applicable to flanged 12-point screws recognized as SAE Standard and intended for general use in automotive and other ground-based vehicles and industrial equipment. Also included is Appendix A, covering runout sleeve gages and gaging. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers should consult manufacturers concerning availability of product.
Standard

Flanged 12-Point Screws
2015-02-26
CURRENT
J58_201502
Included in this SAE Standard are the detailed general and dimensional specifications applicable to flanged 12-point screws recognized as SAE Standard and intended for general use in automotive and other ground-based vehicles and industrial equipment. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers should consult manufacturers concerning availability of product.
Standard

Spring Nuts
1998-05-01
HISTORICAL
J891_199805
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Spring Nuts
2004-10-04
HISTORICAL
J891_200410
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
<< First< Previous12345Next >Last >>
X