Search Results

Standard

HOLES IN BOLT AND SCREW SHANKS AND SLOTS IN NUTS FOR COTTER PINS

1998-05-01

HISTORICAL

J485_199805

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

HOSE CLAMPS

1971-03-01

HISTORICAL

J536B_197103

Standard

Hex Bolts

1990-01-01

CURRENT

J105_199001

Included herein are complete general and dimensional data for the various types of square and hex bolts recognized as SAE Standard and commonly used in automotive and other ground based motor vehicles and industrial equipment. Also included are appendixes covering wrench openings for bolts and thread runout sleeve gages. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Users are requested to consult with manufacturers concerning lists of stock production sizes.

Standard

Hexagon High Nuts

2016-11-18

CURRENT

J482_201611

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

Hexagon High Nuts

2006-04-17

HISTORICAL

J482_200604

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

Hexagon High Nuts

2013-04-15

HISTORICAL

J482_201304

Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.

Standard

Hi-Head Finished Hex Bolts

1990-01-02

CURRENT

J871_199001

This SAE Standard specifies the general and dimensional requirements for hi-head hex cap screws (formerly "finished hex bolts"). Hi-head hex cap screws are intended primarily for use in the heavy construction and industrial equipment industry. The increase in head heights over those of hex cap screws assures good wrenchability where frequent servicing is necessary, where high torquing is a requirement, or where wear on the screw head is a problem.

Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2016-11-18

CURRENT

J483_201611

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2006-03-09

HISTORICAL

J483_200603

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2013-04-15

HISTORICAL

J483_201304

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2016-11-18

CURRENT

J485_201611

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2013-04-16

HISTORICAL

J485_201304

SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.

Standard

Hose Clamps

1992-01-30

CURRENT

J536_199201

Standard

LOCK WASHERS

1974-02-01

HISTORICAL

J489B_197402

This SAE Standard covers the complete dimensional and general specifications, including physical properties and methods of testing, for those types of lock washers intended for use in automotive and general industrial applications.

Standard

Lock Washers

1990-01-01

CURRENT

J489_199001

Not available.

Standard

MECHANICAL AND CHEMICAL REQUIREMENTS FOR NONTHREADED FASTENERS CARBON STEEL SOLID RIVETS

1998-05-01

HISTORICAL

J430_199805

These specifications cover the mechanical and chemical requirements for carbon steel solid rivets used in automotive and other related industries.

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS

1977-07-01

HISTORICAL

J429J_197707

This SAE Standard covers the mechanical and material requirements for steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1½ in., inclusive. NOTE: Previous issues of this standard also covered nuts, now covered separately in SAE J995.

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS

1979-05-01

HISTORICAL

J429K_197905

This SAE Standard covers the mechanical and material requirements for steel bolts, screws, studs, sems,1 and U-bolts2 used in automotive and related industries in sizes to 1½ in, inclusive. Note: Previous issues of this standard also covered nuts, now covered separately in SAE J995 (August, 1967).

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS

1983-08-01

HISTORICAL

J429_198308

This SAE Standard covers the mechanical and material requirements for steel bolts, screws, studs, sems,1 and U-bolts2 used in automotive and related industries in sizes to 1¾ in, inclusive. Note: Previous issues of this standard also covered nuts, now covered separately in SAE J995 (August, 1967).

Standard

MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS

1997-07-01

HISTORICAL

J429_199707

This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, sems1, and U-bolts2 used in automotive and related industries in sizes to 1-1/2 in inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.