Refine Your Search

Topic

Search Results

Standard

Tension Indicating Washer Tightening Method for Fasteners

2018-04-24
CURRENT
J2486_201804
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Standard

Torque-Tension Tightening for Metric Series Fasteners

2017-11-08
CURRENT
J1701M_201711
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used. Also described in this document is the torque management required to achieve satisfactory fastened joint tightening. This guide is limited in application to clearance fit threads, such as the common 6g/6H class of fit. Other thread types including interference fit, mechanical locking, prevailing torque, or forms other than ISO-Metric may apply to some aspects of this standard but are not specifically covered.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2017-09-12
WIP
J174
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

Metric Thread Rolling Screws

2017-09-07
CURRENT
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Mechanical and Material Requirements for Steel Nuts

2017-07-20
CURRENT
J995_201707
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
Standard

Nut and Conical Spring Washer Assemblies

2017-05-30
CURRENT
J238_201705
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard

Torque-Tension Tightening for Inch Series Fasteners

2017-02-09
CURRENT
J1701_201702
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of wrenching employed. Also, described in this document is the torque management required to achieve correct fastener joint tightening. The thread fit of fasteners must be in accordance with Class 2A for external and Class 2B for internal inch threads.
Standard

Blind Rivets - Break Mandrel Type

2017-01-04
CURRENT
J1200_201701
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard

Surface Discontinuities on Nuts

2017-01-04
CURRENT
J122_201701
This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2017-01-03
CURRENT
J174M_201701
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Spring Nuts

2016-11-28
CURRENT
J891_201611
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Push-On Spring Nuts Inch Series - General Specifications

2016-11-23
CURRENT
J892_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw or bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.
Standard

Guide for Rivet Selection and Design Consideration

2016-11-23
CURRENT
J492_201611
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
Standard

Push-On Spring Nuts Metric Series - General Specifications

2016-11-21
CURRENT
J892M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement on the mating metal or plastic studs and in some cases screw bolt threads is considered adequate for the fastening joint application. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.
Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21
CURRENT
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: Nonserrated shank bolts which are heat treated Serrated shank bolts which are case hardened
Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2016-11-18
CURRENT
J1053_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2016-11-18
CURRENT
J1053M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
Standard

Hexagon High Nuts

2016-11-18
CURRENT
J482_201611
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
X