Search Results

This SAE Standard is concerned with the geometrical irregularities of surfaces of solid materials. It established definite classifications for various degrees of roughness and waviness and for several varieties of lay. It also provides a set of symbols for use on drawings and in specifications, reports, and the like. The ranges for roughness and waviness are divided into a number of steps, and the general types of lay are established by type characteristics. This standard does not define what degrees of surface roughness and waviness or what type of lay are suitable for any specific purpose. It does not specify the means by which any degree of such irregularities may be obtained or produced. Neither is it concerned with the other surface qualities such as luster, appearance, color, corrosion resistance, wear resistance, hardness, microstructure, and absorption characteristics, any of which may be governing considerations in specific applications.

This SAE Recommended Practice provides procedures for determining shot peening coverage and relating coverage to part exposure to the media stream. Effectiveness of shot peening is directly dependent on coverage. Inadequate or excessive coverage can be detrimental to fatigue strength and component life.

Blast cleaning may be defined as a mechanical pre-treatment process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. Blast cleaning may be employed for a variety of purposes. It is a well-established method for removing sand from castings and burrs or scale from forgings, mill products, or heat treated parts; to promote machinability; and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces a suitable surface for downstream industrial coatings. All these objectives are often accomplished in the one operation. As a general understanding, this document pertains to blast cleaning only. Any reference to shot peening or other processes is only to explain a context or concept related to blast cleaning.

This SAE Recommended Practice is considered to be tentative and is subject to modification to meet new developments or requirements. It is offered as a guide in the selection and use of cut wire shot.

This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches , preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.

This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.

This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.

This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot. To induce residual compressive stress in surface layers of parts, thereby increasing fatigue strength and resistance to stress-corrosion cracking.

This SAE Recommended Practice describes chemical analysis, hardness, microstructure, and physical characteristic requirements for low carbon cast steel shot to be used for shot peening or blast cleaning operations.

This SAE Recommended Practice Specification provides the procedures for using test strips per SAE J442 for peening processes.

This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.

This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.

This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.

This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.

This SAE Standard and its supplementary detail specifications cover the engineering requirements for the controlled shot peening of a medical device where shot peening is required for enhancement of a material's mechanical properties through the intentional creation of compressive residual stress.

This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers.

This specification covers characteristics for chemistry, microstructure, density, hardness, size, shape and appearance of zirconium oxide based ceramic shot, suitable for peening surfaces of parts by impingement.

This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.

This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.