Refine Your Search

Date

Date

Topic

Topic

Search Results

Viewing 1 to 20 of 72
123Next >Last >>
Sort by relevance
Standard

Marking of Rubber Parts
2024-07-17
WIP
J2332
This SAE Recommended Practice provides a system for marking thermoset rubber parts to designate the general type of material from which the part was fabricated.
Standard

Thermoset Elastomer Specification System
2023-06-02
CURRENT
J2884_202306
This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use, recycled, or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum percent, must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCEs) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F2468.
Standard

Standard Reference Elastomers (SREs) for Characterizing the Effect of Liquids on Vulcanized Rubbers
2023-05-10
CURRENT
J2643_202305
This SAE Standard specifies requirements for vulcanized rubbers in sheet form for use as standards in characterizing the effect of test liquids and service fluids. The appendices contain the standard reference elastomer formulas. The property changes of the SRE in contact with the indicated fluid under specified test conditions are the responsibility of the user. See 7.3 and Table 1. This standard is not designed to provide formulations of elastomeric product compositions for actual service.
Standard

Classification System for Rubber Materials
2023-03-23
CURRENT
J200_202303
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
Standard

Classification System for Thermoplastic Elastomers
2023-03-01
CURRENT
J2558_202303
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. In all cases where provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. This classification is based on SI units.
Standard

Classification System for Rubber Materials
2015-06-19
HISTORICAL
J200_201506
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
Standard

Test Method for Vulcanized Rubber and Thermoplastic Elastomer Determination of Compressive Stress Relaxation (CSR) Response
2015-04-10
WIP
J2979
The scope of this document is to define a test method for performing the Compression Stress Relaxation (CSR) Test with the Automotive Standard (ASD) CSR Jig using the appropriate test fixtures, configurations and procedures. This standard defines the equipment needed, guidelines for running the test, and the format for generating the results and analyzing the data.
Standard

Classification System for Thermoplastic Elastomers
2014-10-27
HISTORICAL
J2558_201410
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. NOTE 1—For the purposes of this document a TPE is defined as a polymeric material that, without further chemical modifications, is capable of recovering from deformations quickly and forcibly and is also capable of being repeatedly softened by heating and hardened by cooling within a temperature range characteristic of the material. NOTE 2—When the TPE product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance to establish the appropriate properties, test methods, and specification test limits.
Standard

Thermoset Elastomer Specification System
2014-06-27
HISTORICAL
J2884_201406
This document provides a method/procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use; recycled; or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum % must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCE’s) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F 2468.
Standard

Standard Reference Elastomers (SRE) for Characterizing the Effect of Liquids on Vulcanized Rubbers
2013-12-17
HISTORICAL
J2643_201312
This SAE Standard specifies requirements for vulcanized rubbers in sheet form for use as standards in characterizing the effect of test liquids and service fluids. The annexes contain the standard reference elastomer formulas. The property changes of the SRE in contact with the indicated fluid under specified test conditions are the responsibility of the user. See 7.3 and Table 1. This standard is not designed to provide formulations of elastomeric product compositions for actual service.
Standard

Marking of Rubber Parts
2013-07-09
CURRENT
J2332_201307
This SAE Recommended Practice provides a system for marking thermoset rubber parts to designate the general type of material from which the part was fabricated.
Standard

Test Method for Vulcanized Rubber and Thermoplastic Elastomer Determination of Compressive Stress Relaxation (CSR) Response
2012-05-30
CURRENT
J2979_201205
The scope of this document is to define a test method for performing the Compression Stress Relaxation (CSR) Test with the Automotive Standard (ASD) CSR Jig using the appropriate test fixtures, configurations and procedures. This standard defines the equipment needed, guidelines for running the test, and the format for generating the results and analyzing the data.
Standard

Classification System for Rubber Materials
2011-12-12
HISTORICAL
J200_201112
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. NOTE 1: The SAE Committee on Automotive Rubber Specifications (CARS) has the sole responsibility for SAE J200. CARS Works closely with and receives input from ASTM Subcommittee D11.30 on Classification of Rubber Compounds with the goal to keep SAE J200 and ASTM D 2000 technically equivalent. Candidate materials presented for development of new tables or for inclusion in Tables A1 or A2 of SAE J200 or Table X1.1 of ASTM D 2000 shall be initiated with the SAE CARS Committee. The procedure to be followed is detailed in Appendix C of SAE J200. NOTE 2: This document may serve many of the needs of other industries in much the same manner as SAE numbered steels.
Standard

Latex Foam Rubbers
2009-10-15
CURRENT
J17_200910
These specifications and methods of testing apply to cellular-rubber products known as latex foam rubbers but do not apply to sponge and expanded rubbers. The base material used in their manufacture may be natural rubber, reclaimed rubber, synthetic rubber, or rubberlike materials, alone or in combination. In case of conflict between the provisions of these general specifications and those of detailed specifications or methods of test for a particular product, the latter shall take precedence. Reference to methods for testing cellular-rubber products should specifically state the particular test or tests desired. The SAE Committee on Automotive Rubber Specifications has concluded, that in light of the fact that SAE J17 is a mirror image of ASTM D 1055, SAE J17 will be eliminated in the year 2005.
Standard

Automotive Rubber Mats
2009-10-15
CURRENT
J80_200910
This SAE Recommended Practice covers the requirements for rubber floor mats made from five types of rubber compounds as required by the physical property requirements of the application.
Standard

Thermoplastic Elastomer Classification System
2009-10-15
CURRENT
J3000_200910
This classification system tabulates the properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. For the purposes of this document a TPE is defined as a polymeric material that, without further chemical modification, is capable of recovering from deformations quickly and forcibly and is also capable of being repeatedly softened by heating and hardened by cooling within a temperature range characteristic of the material. When the TPE product is to be used for purposed where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the plurchaser to consult the supplier in advance to establish the apropriate propeties, test methods, and specification test limits. This classification system is based on the premise that the properties of TPEs can be arranged into characteristic material designations.
Standard

Thermoset Elastomer Specification System
2009-09-10
HISTORICAL
J2884_200909
This document provides a method/ procedure for specifying the properties of vulcanized elastomeric materials (natural rubber or synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. This document covers materials that do not contain any re-use; recycled; or regrind materials unless otherwise agreed to by manufacturer and end user. The use of such materials, including maximum % must be specified using a “Z” suffix. This classification system covers thermoset High Consistency Elastomers (HCE’s) only. Thermoplastic Elastomer (TPE) materials are classified using SAE J2558. Silicone Formed In Place Gasket (FIPG) systems such as Room Temperature Vulcanized (RTV) Silicones, and Liquid Silicone Rubber (LSR) systems are classified using ASTM F 2468.
Standard

Classification System for Rubber Materials
2008-05-15
HISTORICAL
J200_200805
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
123Next >Last >>
X