Search Results

In this study, fuel octane number boosters such as toluene, ethanol, methanol, 2-methylfuran (MF), and 2,5-dimethylfuran (DMF) are blended with primary reference fuels (PRFs) in a cooperative fuel research (CFR) engine at research octane number (RON) relevant conditions. In addition to RON determination, engine operation is characterized by measuring (i) cylinder, intake and exhaust pressure, (ii) averaged intake and exhaust temperature, and (iii) air-fuel-ratio. For known fuel blends, the measured RON corresponds well with existing literature. The addition of MF in PRF yields a significant increase in RON and blending octane numbers (indicating booster impact) up to 216. Cylinder pressure fluctuations, the classical definition of knock intensity, are however not consistent, deviating between PRFs and all boosted blends at higher RON values. Moreover, some fuel blends exhibit scarcely any knocking behavior in the test conditions.

Knocking combustion is a major obstacle towards engine downsizing and boosting—popular techniques towards meeting the increasingly stringent emission standards of SI engines. The commercially available gasoline is a mixture of many chemical compounds like paraffins, isoparaffins, olefins and aromatics⁠. Therefore, the modeling of its combustion process is a difficult task. Additionally, the blends of certain compounds exhibit non-linear behavior in comparison to the pure components in terms of knock resistance. These facts require further analysis from the perspective of combustion chemistry. The present work analyses the effects of blending ethanol to FACE-C gasoline. A range of pressures, temperatures, and equivalence ratios has been considered for this purpose. The open source softwares Cantera version 2.4.0 and OpenSMOKE++ Suite have been used for the simulations.

A novel high pressure SCR spray system is investigated both experimentally and numerically. RANS simulations are performed using Star-CD and polyhedral meshing. This is one of the first studies to compare droplet breakup models and AdBlue injection with high injection pressure (Pinj=200 bar). The breakup models compared are the Reitz-Diwakar (RD), the Kelvin-Helmholtz and Rayleigh-Taylor (KHRT), and the Enhanced Taylor Analogy Breakup (ETAB) model. The models are compared with standard model parameters typically used in diesel fuel injection studies to assess their performance without any significant parameter tuning. Experimental evidence from similar systems seems to be scarce on high pressure AdBlue (or water) sprays using plain hole nozzles. Due to this, it is difficult to estimate a realistic droplet size distribution accurately. Thereby, there is potential for new experimental data to be made with high pressure AdBlue or water sprays.

The direct injection (DI) natural gas engine is considered as one of the promising technologies to achieve the continuing goals of the higher efficiency and reduced emissions for internal combustion engines. Shock wave phenomena can easily occur near the nozzle exit when high pressure gaseous fuel is injected directly into the engine cylinder. In the present study, high pressure gas issuing from a prototype gas injector was experimentally studied using planar laser-induced fluorescence (PLIF) technique. Acetone was selected as a fuel tracer. The effects of injection pressures on the flow structure and turbulent mixing were investigated based on a series of high resolution images. The jet macroscopic structures, such as jet penetration, cone angle and jet volume, are analyzed under different injection pressures. Results show that barrel shock waves can significantly influence the jet flow structure and turbulent mixing.

Over the past decade significant research and development activities have been invested in alternative fuels in order to reduce our dependency on fossil fuel sources and reduce CO₂ and local emissions from traffic. One result of these R&D efforts is paraffinic diesel fuels, which can be used with existing vehicle fleets and infrastructures. Paraffinic diesels also have other benefits compared to conventional diesels, for example, a very high cetane number and the lack of sulfur and aromatic compounds. These characteristics are beneficial in terms of exhaust gas emissions, something which has been demonstrated in numerous studies. The objective of this study was to develop low-emission combustion technologies for paraffinic renewable diesel in a compression ignition engine, and to study the possible benefits of oxygenated paraffinic diesel.

Compressed natural gas direct-injection (CNG-DI) engines based on diesel cycle combustion system with pilot ignition have ability to achieve high thermal efficiency and low emissions. Generally, underexpanded jets can be formed when the high pressure natural gas is injected into the combustion chamber. In such conditions, shock wave phenomena are the typical behaviors of the jet, which can significantly influence the downstream flow structure and turbulent mixing. In the present study, the characteristics of high-pressure transient jets were investigated using planar laser-induced fluorescence (PLIF) of acetone as a fuel tracer. The evolution of the pulsed jet shows that there are three typical jet flow patterns (subsonic, moderately underexpanded, and highly underexpanded) during the injection. The full injection process of high-pressure pulsed jets is well described with the help of these shock wave structures.

The objective of this paper is to analyse the performance and the combustion of a large-bore single-cylinder medium speed engine running with hydrotreated vegetable oil. This fuel has a paraffinic chemical structure and high Cetane number. These features enable achievement of complete and clean combustion with different engine setups. The main benefits are thus lower soot and nitrogen oxides emissions compared to diesel fuel. The facility used in this study is a research engine, where the conditions upstream the machine, the valve timing and the injection parameters are fully adjustable. In fact, the boundary conditions upstream and downstream the engine are freely controlled by a separated supply air plant and by a throttle valve, located at the end of the exhaust pipe. The injection system is common-rail: rail pressure, injection timing and duration are completely adjustable.

The aim of current study was to compare the global fuel spray characteristics between renewable hydrotreated vegetable oil (HVO) and crude oil-based EN 590 diesel fuel. According to previous studies, the use of HVO enables reductions in carbon monoxide (CO), total hydrocarbon (THC), nitrogen oxide (NOx) and particle matter (PM) emissions without any changes to the engine or its controls. Fuel injection strategies and global fuel spray characteristics affect on engine combustion and exhaust gas emissions. Due to different physical properties of two different fuels, fuel spray characteristics differ. Fuel spray studies were performed with backlight imaging using a pressurized test chamber imitating real engine conditions at the end of compression stroke. However, the measurements were made in non-evaporative conditions. Various injection parameters such as injection pressures and orifice diameter were tested.

Natural gas has been considered as one promising alternative fuel for internal combustion (IC) engines to meet strict engine emission regulations and reduce the dependence on petroleum oil. Although compressed natural gas (CNG) intake manifold injection has been successfully applied into spark ignition (SI) engines in the past decade, natural gas direct injection compression ignition (DICI) engine with new injection system is being pursued to improve engine performance. Gas jet behaves significantly different from liquid fuels, so the better understanding of the effects of gas jet on fuel distribution and mixing process is essential for combustion and emission optimization. The present work is aimed to gain further insight into the characteristics of low pressure gas jet. An experimental gas jet investigation has been successfully conducted using tracer-based planar laser-induced fluorescence (PLIF) technique. For safety reason, nitrogen (N₂) was instead of CNG in this study.

The objective of this paper is to analyze the performance and the combustion of a large-bore medium-speed engine running with hydro-treated vegetable oil (HVO) at low engine load. This fuel has a paraffinic chemical structure and high cetane number (CN). The main benefits are thus lower emission compared to diesel fuel and low soot values. The facility used in this study is a research engine, where the conditions before and after the machine, the valve timing and the injection parameters are fully adjustable. Several in-cylinder conditions before the combustion have been tested. The results are promising and show the benefits of HVO compared to diesel fuel. In fact, it has been possible to reduce nitrogen oxides (NOx) emission over 50% running with HVO and opportunely tuned valve timing.

Several high-speed diesel engine test runs were carried out during 2010 in Aalto University using a single-cylinder research engine. The main focus was on miller cycle and exhaust gas recirculation (EGR) tests using hydrotreated vegetable oil (HVO) as fuel. But also reference tests were run using both HVO and regular EN590 diesel in normal engine configuration and running parameters. The miller tests included a sweep of three different intake valve closing timings and also a sweep with advanced start of injection. The results showed a reduction in both nitrous oxides (NOx) and smoke emissions. EGR tests showed a significant decrease in NOx emissions as was expected. The lower smoke emissions of HVO compared to EN590 enable higher EGR percentages with similar PM emission and hence bigger NOx emission reduction.

Experimental spray tip penetrations obtained from a large-bore medium-speed optical diesel engine were compared to CFD simulations. The optical spray results are unique as they are obtained from a running large-bore (200mm) diesel engine. The experimental spray tip penetration measurements were obtained during the early spray development period when the spray evaporation had not yet reached the quasi steady-state phase. The CFD simulations were conducted in both static chamber environment and in engine conditions. The fuel injection boundary conditions were obtained from 1-D simulations. Within the error margins associated with the experimental and computational data, relatively good accuracy was obtained between measured and simulated spray tip penetration. It was also observed that it is very important to have accurate fuel injection mass flow rate data. This was observed after a sensitivity analysis was made for the injection duration and fuel mass quantity.

The objective of this study is to achieve high reduction of NOx emissions in a medium-speed single-cylinder research engine. The main feature of this research engine is that the gas exchange valve timing is completely adjustable with electro-hydraulic actuators. The study is carried out at high engine load and using a very advanced Miller valve timing. Since the engine has no turbocharger, but a separate charge air system, 1-D simulations are carried out to find the engine setup, which would be close to the operating points of a real engine. The obtained NOx reduction is over 40% with no penalty in fuel consumption.

This study is presenting a comparative spray study of modern large bore medium speed diesel engine common rail injectors. One subject of paper is to focus on nozzles with same nominal flow rate, but different machining. The other subject is penetration velocity measurements, which have a new approach when trying to understand the early phase of transient spray. A new method to use velocimetry for spray tip penetration measurements is here introduced. The length where spray penetration velocity is changed is found. This length seems to have clear connection to volume fraction of droplets at gas. These measurements also give a tool to divide the development of spray into acceleration region and deceleration region, which is one approach to spray penetration. The measurements were performed with backlight imaging in pressurized injection test rig at non-evaporative conditions. Gas density and injection pressure were matched to normal diesel engine operational conditions.

The objective of this study was to build up an optical access into a large bore medium-speed research engine and carry out the first fuel spray Particle Image Velocimetry (PIV) measurements in the running large bore medium-speed engine in high pressure environment. The aim was also to measure spray penetration with same optical access and apparatus. The measurements were performed in a single-cylinder large bore medium-speed research engine, the Extreme Value Engine (EVE) with optical access into the combustion chamber. The authors are not aware of any other studies on optical spray measurements in large bore medium-speed diesel engines. Successful optical measurements of the fuel spray penetration and the velocity fields were carried out. This confirms that the exceptional component design and laser sheet alignment used in this study proved to be valid for optical fuel spray measurements in large-bore medium-speed diesel engines.

Hydrotreating of vegetable oils or animal fats is an alternative process to esterification for producing biobased diesel fuels. Hydrotreated products are also called renewable diesel fuels. Hydrotreated vegetable oils (HVO) do not have the detrimental effects of ester-type biodiesel fuels, like increased NOx emission, deposit formation, storage stability problems, more rapid aging of engine oil or poor cold properties. HVOs are straight chain paraffinic hydrocarbons that are free of aromatics, oxygen and sulfur and have high cetane numbers. In this paper, NOx - particulate emission trade-off and NOx - fuel consumption trade-off are studied using different fuel injection timings in a turbocharged charge air cooled common rail heavy duty diesel engine. Tested fuels were sulfur free diesel fuel, neat HVO, and a 30% HVO + 70% diesel fuel blend. The study shows that there is potential for optimizing engine settings together with enhanced fuel composition.

The flow through the valves of an engine cylinder head is very complex in nature due to very high gas velocities and strong flow separation. However, it is also the typical situation in almost every engine related flow. In order to gain better understanding of the flow features after the cylinder head, and to gain knowledge of the performance level that can be expected from CFD analysis, flow field measurements and computations were made in an engine rig. Particle image velocimetry (PIV) and paddle wheel measurements have been conducted in a static heavy-duty diesel engine rig to characterize the flow features with different valve lifts and pressure differences. These measurements were compared with CFD predictions of the same engine. The simulations were done with the standard k-ε turbulence model and with the RNG turbulence model using the Star-CD flow solver.