Search Results

Standard

Identification Marking Methods

2006-03-24

HISTORICAL

AS478M

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification Marking Methods

1998-07-01

HISTORICAL

AS478K

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification Marking Methods

2021-01-21

HISTORICAL

AS478R

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification Marking Methods

2022-11-02

CURRENT

AS478S

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification Marking Methods

2017-11-03

HISTORICAL

AS478P

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification Marking Methods

2015-04-28

HISTORICAL

AS478N

This standard provides the following: a Definition of terms pertaining to marking. b Symbols for marking location. c Requirements and restrictions for permanent markings. d Types of marking methods. e Rules for designating marking methods. f Table listing marking methods.

Standard

Identification and Coding of Fluid and Electrical Piping System Functions

2006-05-08

HISTORICAL

AIR1273A

This SAE Aerospace Information Report establishes a positive identification of the functions and, if applicable, the hazards and direction of flow of pipe, hose, tube, or electrical conduit lines.

Standard

Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts

2018-08-09

CURRENT

AS269J

This SAE Aerospace Standard (AS) provides material identification codes for aluminum alloys, copper alloys, carbon steels, alloy steels, titanium alloys, corrosion resistant materials, and heat resistant materials that are used to make AN, MS, and AS engine and propeller standard utility parts. This document also provides similar material codes for company parts (such as nuts, bolts, etc.) having design configuration similar to other company parts or the engine and propeller standard utility parts (AN, MS, and AS) that are not of the same material.

Standard

Identification of Material for AN, MS, and AS Engine and Propeller Standard Utility Parts and Also for Company Parts

2012-11-01

HISTORICAL

AS269H

This SAE Aerospace Standard (AS) provides material identification codes for aluminum alloys, copper alloys, carbon steels, alloy steels, titanium alloys, corrosion resistant materials, and heat resistant materials that are used to make AN, MS, and AS engine and propeller standard utility parts. This document also provides similar material codes for company parts (such as nuts, bolts, etc.) having design configuration similar to other company parts or the engine and propeller standard utility parts (AN, MS, and AS) that are not of the same material.

Standard

Identification of Standard Utility Parts - Bolts and Nuts

2018-08-23

HISTORICAL

AIR3260

This information report presents recommendations on part number marking which provides for the maximum identification on bolts and nuts while ensuring adequate readability.

Standard

Identification of Standard Utility Parts – Bolts and Nuts

2024-03-04

CURRENT

AIR3260A

This information report presents recommendations on part number marking which provides for the maximum identification on bolts and nuts while ensuring adequate readability.

Standard

Insert - Cres Helical Coil Fine Thread, Locking (Low Friction Systems) 2.5 Dia Nom Length

2023-11-17

WIP

AS3096B

No scope available.

Standard

Insert - Cres Helical Coil Fine Thread, Locking (Low Friction Systems) 3 Dia Nom Length

2023-11-17

WIP

AS3097B

No scope available.

Standard

Insert - Screw Thread, Thin Wall, Self-Locking UNS N07718, Silver Plated, Class: 185 ksi/1025 °F, Procurement Specification

2004-03-24

HISTORICAL

AS3506A

This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.

Standard

Insert - Screw Thread, Thin Wall, Self-Locking UNS N07718, Silver Plated, Class: 185 ksi/1025 °F, Procurement Specification

2001-10-01

HISTORICAL

AS3506

This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.

Standard

Insert - Screw Thread, Thin Wall, Self-Locking, UNS N07718, Silver Plated, Class: 185 ksi/1025 °F, Procurement Specification

2019-04-09

CURRENT

AS3506B

This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.

Standard

Insert - Thin Wall, Self-Locking Short and Long Length Installation and Removal of

2019-07-01

CURRENT

AS3507C

This SAE Aerospace Standard (AS) provides minimum design, installation (by manual and power methods) and removal requirements for AS3504 and AS3505 thin wall inserts and is applicable when specified on engineering drawings or in procurement documents.

Standard

Insert - Thin Wall, Self-Locking Short and Long Length Installation and Removal of

2004-07-23

HISTORICAL

AS3507A

This SAE Aerospace Standard (AS) provides minimum design, installation, and removal requirements for AS3504 and AS3505 thin wall inserts and is applicable when specified on engineering drawings or in procurement documents.

Standard

Insert - Thin Wall, Self-Locking Short and Long Length Installation and Removal of

2018-08-23

HISTORICAL

AS3507B

This SAE Aerospace Standard (AS) provides minimum design, installation (by manual and power methods) and removal requirements for AS3504 and AS3505 thin wall inserts and is applicable when specified on engineering drawings or in procurement documents.

Standard

Insert - Thin Wall, Self-Locking, Metric Short and Long Length Installation and Removal Of

2018-08-23

HISTORICAL

MA4811

This SAE Metric Aerospace Standard (MA) provides minimum design, installation, and removal requirements for MA3520 and MA3521 thin wall inserts and is applicable when specified on engineering drawings or in procurement documents.