Search Results

This specification establishes the requirements for a waterborne, corrosion inhibiting, chemical and solvent resistant, anodic electrodeposition epoxy primer capable of curing at 200 to 210 °F (93 to 99 °C).

This specification covers tapes for masking during paint stripping operations (6.1).

This specification establishes requirements for a heat resistant aluminized organic coating with sufficient corrosion and erosion resistance for the finished substrate.

This specification establishes requirements for a tape that is used to perform organic coatings adhesion testing.

This standard establishes the minimum requirements for training, examination, and certification of aerospace coatings application personnel applying liquid organic coatings to interior structural or exterior substrates. It establishes criteria for the certification of personnel requiring appropriate knowledge of the technical principles underlying aircraft surface preparation and coatings application for both protective and decorative purposes. Persons certified under this document shall receive documentation of certification by the Certifying Agency. Persons who successfully complete the requirements of this certification standard are considered to be able to successfully and consistently perform a broad spectrum of aerospace coatings application tasks to achieve the desired engineering purposes.

This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: a Color Chip Representation, Fan Deck: Suitable for color identification and selection. b Color Chip Representation, Color Book: Suitable for color identification and selection. c Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. d Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.

This specification covers fluorocarbon (FKM) elastomeric coating materials for fiber-reinforced-resin composite structures in the form of two-component brushable or sprayable liquids.

This specification establishes the performance requirements for non-chromated materials used for surface preparation of metallic aircraft surfaces prior to applying organic coatings.

This specification establishes requirements for thermoset protective coatings in powder form.

This specification establishes requirements for three types of corrosion preventative coatings for protection of aircraft integral fuel tanks.

This standard presents the colors used by Government Activities in a format suitable for color selection, color matching and for quality control inspection. This document describes the designation and use of the color chips of this standard. Formats for color chip representation and precise color matching formats are as described below: a Color Chip Representation, Fan Deck: Suitable for color identification and selection. b Color Chip Representation, Color Book: Suitable for color identification, comparison and selection. c Precise Color Matching, Individual Color Chips: A 3 × 5 inch color chip supplied in a 3 × 5 inch protective envelope, suitable for color matching and quality control inspection purposes. d Precise Color Matching, Sets of Color Chips: A set containing one 3 × 5 inch color chip in its protective envelope for each Fed-Std-595 color, suitable for color matching and quality control inspection purposes.

This specification covers the requirements for two classes and two types of rain erosion resistant coatings. This specification has been prepared as a direct replacement for the Military Specification MIL-C-83231A Notice 1. These products have been used for protecting glass fabric reinforced plastic laminates and other plastic parts used for exterior surfaces of aircraft and missiles, but usage is not limited to such applications.

This specification establishes requirements for a heat resistant aluminized organic coating with sufficient corrosion and erosion resistance for the finished substrate.

This specification covers a semigloss black baking enamel based on a phenolic resin.

This specification covers a glyceryl-phthalate-base paint vehicle in the form of a liquid.

This specification covers a two-component, polytetrafluoroethylene-filled polyurethane coating material supplied in kit form.

This specification covers two-component colored systems composed of a resin and a miscible hardener supplied in kit form.

This specification covers a face-up type of water-applied, solvent-applied, or adhesive-applied decalcomanias.

This specification covers a ready-to mix, two component, self-curing, inorganic zinc rich primer for use on steel surfaces.

This specification covers a zinc chromate primer in the form of a liquid.