Search Results

Standard

Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7049-T73) Solution and Precipitation Heat Treated

2023-05-17

CURRENT

AMS4111F

This specification covers an aluminum alloy in the form of die forgings or hand forgings up to 5 inches (125 mm) in thickness, and forging stock of any size (see 8.7).

Standard

Aluminum Alloy, Coiled Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-T4) Solution Treated

2023-05-10

CURRENT

AMS4477B

This specification covers an aluminum alloy in the form of coiled sheet 0.010 to 0.249 inch (0.25 to 6.32 mm), inclusive, in thickness, supplied in the -T4 temper (see 8.5).

Standard

Aluminum Alloy, Welding Wire 5.0Si - 1.2Cu - 0.50Mg (C355.0)

2023-05-10

CURRENT

AMS4245G

This specification covers an aluminum alloy in the form of welding wire.

Standard

Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg - 0.25Cr (5052-O) Annealed

2023-05-10

CURRENT

AMS4071P

This specification covers an aluminum alloy in the form of drawn, round seamless tubing having a wall thickness of 0.010 to 0.450 inch (0.25 to 11.43 mm), inclusive, and nominal outside diameters of 0.125 to 3.000 inch (3.18 to 76.2 mm), inclusive (see 8.5).

Standard

Aluminum Alloy, Alclad Sheet and Plate 4.3Cu - 1.4Mg - 0.60Mn (Alclad 2524-T3) Solution Heat Treated and Cold Worked

2023-05-10

CURRENT

AMS4296D

This specification covers an aluminum alloy in the form of sheet and plate 0.032 to 0.310 inch (0.81 to 7.87 mm), inclusive, in thickness, clad on both sides (see 8.5).

Standard

Tolerances Copper and Copper Alloy Sheet, Strip, and Plate

2023-05-10

CURRENT

AMS2222L

This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted.

Standard

Aluminum Alloy Die Forgings (7050-T74) Solution Heat Treated and Overaged

2023-05-10

CURRENT

AMS4107H

This specification covers an aluminum alloy in the form of die forgings up to 6.000 inches (152.40 mm), inclusive, in nominal thickness and forging stock of any size (see 8.6).

Standard

Aluminum Alloy, Sheet, and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr Solution and Precipitation Heat Treated (2219 -T81/-T851)

2023-05-10

CURRENT

AMS4599B

This specification covers an aluminum alloy in the form of sheet and plate from 0.020 to 6.000 inches (0.51 to 152.40 mm), inclusive, in thickness (see 8.5).

Standard

Aluminum Alloy, Extruded Profiles 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated

2023-05-10

CURRENT

AMS4113G

This specification covers an aluminum alloy in the form of extruded profiles such as angles, channels, tees, zees, I-beams, and H-beams.

Standard

Aluminum Alloy, Sheet and Plate, Alclad, 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T861 Sheet and Plate), Solution Heat Treated, 6% Cold Worked and Artificially Aged

2023-03-30

WIP

AMS4467C

This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T861 temper.

Standard

Aluminum Alloy, Extrusionsn 4.0Cu - 1.3Mg - 0.60Mn (2026-T3511) Solution Heat Treated and Stress Relieved by Stretching (Composition similar to UNS A92026)

2023-03-20

WIP

AMS4338C

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles (shapes) with a maximum cross-sectional area of 25 in2 (161 cm2), a maximum circle size of 12 inches (305 mm) and a nominal thickness up to 3.250 inch (82.54 mm), inclusive.

Standard

Aluminum Alloy Rings, Rolled or Forged 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T651, 2014-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated

2023-03-20

WIP

AMS4314F

This specification covers an aluminum alloy in the form of rolled or forged rings up to 8 inches (203 mm), inclusive, in nominal thickness at the time of heat treatment, and having an OD to wall thickness ratio of 10 or greater (see 8.6).

Standard

Aluminum Alloy, Extrusion, 2.7Cu - 1.8Li - 0.7Zn - 0.3Mn - 0.3Mg - 0.08Zr (2099-T81), Solution Heat Treated, Stress Relieved by Stretching 1 to 3% and Aged

2023-03-20

WIP

AMS4459C

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles (shapes) from 0.375 to 1.300 inches (9.53 to 33.02 mm) in diameter or thickness, produced with cross sectional area of 22.5 in2 (145 cm2) maximum, and a circumscribing circle diameter (circle size) of 17.4 inches (44.2 cm) maximum. See 8.3 for definition of circumscribing circle size.

Standard

Aluminum Alloy, Alclad Sheet (6156-T4) 1.0Si - 0.90Cu - 0.60Mn - 0.90Mg Solution Heat Treated and Naturally Aged (Composition similar to UNS AA6156)

2023-03-20

WIP

AMS4405D

1.1 Form This specification covers an aluminum alloy procured in the form of sheet 0.078 to 0.197 inch (2.00 to 5.00 mm), inclusive, in nominal thickness, Alclad on both sides (see 8.5). 1.2 Application These products have been used typically for formed structural parts requiring good formability in T4 temper and ability to develop improved resistance to fatigue crack growth and high toughness with moderate strength when aged to T62 temper, but usage is not limited to such applications.

Standard

Core, Honeycomb, Aluminum Alloy, Corrosion Inhibited, For Sandwich Construction, 5056, 350 (177)

2023-03-20

WIP

AMS4349F

This specification covers bonded honeycomb core made of aluminum alloy and supplied in the form of blocks, slices, or other configurations as ordered.

Standard

Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (2024 -T361 Sheet/Plate with 1½% Alclad) Solution Heat Treated, 6% Cold Worked and Naturally Aged

2023-03-20

WIP

AMS4194F

This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T361 temper.

Standard

Aluminum Alloy, Hand Forgings 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7352) Solution Heat Treated, Stress Relieved by Compression, and Precipitation Heat Treated

2023-03-20

WIP

AMS4247D

This specification covers an aluminum alloy in the form of hand forgings up to 5 inches, incl (127 mm, incl) in nominal thickness at the time of heat treatment, procured to inch/pound dimensions (see 8.6).

Standard

Aluminum Alloy Extrusions, 2.7Cu - 2.2Li - 0.12Zr (2090-T86), Solution Heat Treated, Cold Worked, and Precipitation Heat Treated

2023-03-20

WIP

AMS4232E

This specification covers an aluminum alloy in the form of extruded bars, rods, and profiles up to 0.499 inches (12.67 mm) in nominal diameter, or least thickness, and under 10 in2 (65 cm2) in cross-sectional area.

Standard

Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6)Solution and Precipitation Heat Treated (Requiring Fatigue and Fracture Toughness Testing) (Composition similar to UNS A43570)

2023-03-20

WIP

AMS4249C

This specification covers an aluminum alloy in the form of castings.

Standard

Dendrite Arm Spacing of Structural Aircraft Quality D357 Aluminum Allow Castings, Determination and Acceptance of

2023-03-20

WIP

ARP1947D

This document covers the recommended practice for determining the acceptability of the dendrite arm spacing (DAS) of D357-T6 aluminum alloy castings required to have tensile strength not lower than 50000 psi (345 MPa).To apply this method, at least two coupons used for DAS measurement and two tensile specimens shall be attached in locations defined by the cognizant engineering organization.Areas of the casting which require DAS control must be accessible for surface DAS measurements, or if internal locations are to be tested, such locations shall be defined by the cognizant engineering organization.