Search Results

Standard

Aluminum Alloy Forgings and Rolled or Forged Rings and Forging Stock, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061 - T4), Solution Heat Treated and Naturally Aged

2023-12-13

WIP

AMS4146J

This specification covers an aluminum alloy in the form of die forgings up to 4 inches (102 mm), hand forgings up to 8 inches (203 mm), rolled or forged rings up to 2.5 inches (63.5 mm) in thickness, and forging stock (see 8.6).

Standard

Magnesium Alloy, Plate 4.0Y - 2.25Nd - 0.5Zr (WE43C - T5) Precipitation Heat Treated

2023-12-13

CURRENT

AMS4371C

This specification covers a magnesium alloy in the form of rolled plate from 0.500 up to 6.0 inches (12.7 to 152.4 mm), inclusive (see 8.5).

Standard

Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged

2023-12-13

CURRENT

AMS4337C

This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.500 to 1.500 inch (12.7 to 38.1 mm), inclusive, in nominal thickness, and having a maximum cross-sectional area of 20 square inches (129 cm2) and a maximum circle size of 10 inches (254 mm) (see 8.7).

Standard

Aluminum Alloy, Die and Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T74) Solution and Precipitation Heat Treated

2023-12-13

CURRENT

AMS4149F

This specification covers an aluminum alloy in the form of die and hand forgings 6.000 inches (152.00 mm) and under in nominal thickness at time of heat treatment (see 8.6).

Standard

Aluminum Alloy, Plate (7160-T7651), 7.0Zn - 2.2Cu - 1.5Mg - 0.10Zr, Solution Heat Treated, Stress Relieved, and Overaged

2023-12-13

WIP

AMS4378A

This specification covers an aluminum alloy in the form of plate 1.000 to 6.000 inches (25.40 to 152.40 mm), inclusive, in nominal thickness (see 8.5).

Standard

Tolerances Copper and Copper Alloy Seamless Tubing

2023-12-01

CURRENT

AMS2223J

This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy seamless tubing ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range.

Standard

Aluminum Alloy Bars, Rods, and Wire, Rolled, Drawn, or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6, -T651) Solution and Precipitation Heat Treated

2023-11-22

CURRENT

AMS4121K

This specification covers an aluminum alloy in the form of bars, rods, and wire.

Standard

Filler Metal, Aluminum Brazing 10Si - 4.0Cu (4145)

2023-11-10

CURRENT

AMS4184H

This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips (see 8.6).

Standard

Aluminum Alloy Sheet and Plate, 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr, 7075: (-T73 Sheet, -T7351 Plate), Solution Heat Treated and Overaged

2023-11-10

CURRENT

AMS4078L

This specification covers an aluminum alloy in the form of sheet and plate over 0.039 to 4.000 inches (over 0.991 to 101.60 mm), inclusive, in thickness (see 8.6).

Standard

Aluminum Bronze, Bars, Rods, Shapes, Tubes, and Forgings 81.5Cu - 10.0Al - 4.8Ni - 3.0Fe Drawn and Stress Relieved (HR50) or Temper Annealed (TQ50)

2023-11-10

CURRENT

AMS4640J

This specification covers an aluminum bronze alloy in the form of bars, rods, shapes, tubes, forgings, and forging stock (see 8.5).

Standard

Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6, 7075-T6510, 7075-T6511) Solution Heat Treated, Stress Relieved by Stretching when Required and Precipitation Heat Treated

2023-11-10

CURRENT

AMS4154S

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.

Standard

Aluminum Alloy, Sheet and Plate 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T4 Sheet, -T451 Plate) Solution Heat Treated and Naturally Aged

2023-11-10

CURRENT

AMS4026N

This specification covers an aluminum alloy in the form of sheet and plate from 0.006 to 3.000 inches (0.15 to 76.20 mm), inclusive, in nominal thickness (see 8.5).

Standard

Brass, Naval, Bars and Rods, 60.5Cu - 38.5Zn - 0.75Sn, Hard Temper (H04)

2023-10-16

CURRENT

AMS4612L

This specification covers a copper alloy (naval brass) in the form of bars and rods.

Standard

Copper Powder 99.0 Cu, Minimum As Fabricated

2023-10-06

CURRENT

AMS4740E

This specification covers elemental copper in the form of powder (see 8.5).

Standard

Aluminum Alloy Sheet, 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761), Solution Heat Treated and Overaged

2023-09-29

WIP

AMS4085G

This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inches (1.02 to 6.32 mm), inclusive, in thickness (see 8.5).

Standard

Aluminum Alloy, Plate, 8.1Zn - 2.3Mg - 1.0Cu - Zr (7449-T7651), Solution Heat Treated, Stress Relieved, and Overaged

2023-09-29

WIP

AMS4250D

This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inch (6.35 to 102.0 mm) inclusive, in nominal thickness (see 8.5).

Standard

Magnesium Alloy, Investment Castings, 10Al (AM100A-T6), Solution and Precipitation Heat Treated

2023-09-29

WIP

AMS4455J

This specification covers a magnesium alloy in the form of investment castings.

Standard

Magnesium Alloy, Investment Castings, 9.0Al - 2.0Zn (AZ92A-T6), Solution and Precipitation Heat Treated

2023-09-29

WIP

AMS4453H

This specification covers a magnesium alloy in the form of investment castings.

Standard

Aluminum Alloy Tubing, Seamless, Drawn, 1.8Cu - 1.0Mg - 0.8Si - 0.20Cr, Solution Heat Treated, Stress-Relieved by Stretching, and Aged (2013-T4511)

2023-09-29

WIP

AMS4469B

This specification covers an aluminum alloy in the form of seamless, drawn tubing having a nominal wall thickness of 0.120 to 0.400 inch (3.00 to 10.00 mm) inclusive (see 8.4).

Standard

Aluminum Alloy, Plate (7085-T7451), 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr, Solution Heat Treated, Stress-Relieved, and Overaged

2023-09-29

WIP

AMS4470D

This specification covers an aluminum alloy in the form of plate 3.000 to 7.000 inches (76.20 to 177.80 mm) in nominal thickness (see 8.5).