Search Results

Standard

Heat Treatment of Aluminum Alloy Raw Materials

2023-03-08

CURRENT

AMS2772H

This specification covers requirements and recommendations for the heat treatment of wrought aluminum alloy raw materials (see 2.2.1) by producers. It supersedes AMS-H-6088 and replaces MIL-H-6088.

Standard

Rings, Sealing, Cast Tin Bronze, 80Cu - 19Sn, As Cast

2023-02-27

WIP

AMS7322H

This specification covers a cast tin bronze in the form of sealing rings.

Standard

Aluminum Bronze Alloy, Centrifugal and Continuous-Cast Castings, 81.5Cu - 10.3Al - 5.0Ni - 2.8Fe, Quench Hardened and Temper Annealed (TQ50)

2023-02-27

WIP

AMS4880E

This specification covers an aluminum bronze alloy in the form of centrifugal and continuous-cast castings.

Standard

Copper Nickel Tin Alloy Plate, 77Cu – 15Ni – 8Sn, Solution Annealed and Spinodal Hardened (TX 00)

2023-02-27

WIP

AMS4595A

This specification covers a copper-nickel-tin alloy in the form of plate.

Standard

Aluminum Alloy, Discontinuously Reinforced Extruded Bar, Rod, Wire and Shapes (2124A/SiC/25p (3 µm) (T1P)

2023-02-27

WIP

AMS4379A

This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and SiC particulate. It is produced in the form of extruded bar, rod, wire and shapes with cross section inclusive of 1 inch (25.4 mm) diameter or less.

Standard

Aluminum Alloy, Discontinuously Reinforced Extruded Bar, Rod, Wire and Shapes (2124A/SiC/25p (0.7 µm) (T1P)

2023-02-27

WIP

AMS4369A

This specification covers a discontinuously reinforced aluminum alloy (DRA) made by mechanical alloying 2124A aluminum powder and SiC particulate. It is produced in the form of extruded bar, rod, wire and shapes with cross section inclusive of 1 inch (25.4 mm) diameter or less.

Standard

Copper-Beryllium Alloy, Bars and Rods, 98Cu - 1.9Be (CDA 172), Hard Temper (TD04)

2023-02-27

WIP

AMS4651D

This specification covers a copper-beryllium alloy in the form of bars and rods.

Standard

Copper-Beryllium Alloy Sheet, Strip, and Plate, 98Cu - 1.9Be, Solution Heat Treated (TB00)

2023-02-27

WIP

AMS4530K

This specification covers one type of copper-beryllium alloy in the form of sheet, strip, and plate.

Standard

Copper Nickel Tin Alloy, Bars and Rods, 77Cu – 15Ni – 8Sn, Solution Annealed and Spinodal Hardened (TX 00)

2023-02-27

WIP

AMS4596C

This specification covers a copper-nickel-tin alloy in the form of bars and rods. When tube is ordered to AMS4596, it shall be supplied to AMS4598.

Standard

Castings, Leaded Bronze, Sand and Centrifugal 80Cu - 10Sn - 9.5Pb As Cast

2023-02-27

WIP

AMS4842G

This specification covers a leaded bronze in the form of sand and centrifugal castings.

Standard

Aluminum Alloy, Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr Annealed (7075-O) or, When Specified, “As Fabricated” (7075-F)

2023-02-20

CURRENT

AMS4044P

This specification covers an aluminum alloy in the form of sheet and plate from 0.008 to 2.000 inches (0.20 to 50.80 mm), inclusive, in thickness, supplied in the annealed (O) condition (see 8.5).

Standard

Heat Treatment of Magnesium Alloy Castings

2023-02-16

WIP

AMS2768D

This specification covers the engineering requirements for heat treatment of magnesium alloy castings and for parts machined from castings.

Standard

Phosphor Bronze Bars, Rods, and Tubing 95Cu - 5Sn Hard Temper

2023-02-14

CURRENT

AMS4625J

This specification covers one type of bronze in the form of bars and rods of any size, and tubing over 1.00 inch (25.4 mm) in nominal outer diameter (see 8.5).

Standard

GAD23AA Casting Approval Responsibility

2023-02-13

WIP

GAD23AA

All casting material specifications prepared by Committee D.

Standard

Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T77511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged (Composition Similar to UNS A97150)

2023-02-13

WIP

AMS4345D

This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing 2.000 inches (50.80 mm) and under in nominal diameter or least thickness (wall thickness of tubing) with a maximum cross-sectional area of 20 in2 (129 cm2), and a maximum circle size of 10 inches (254 mm) (see 8.8).

Standard

Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged (Composition similar to UNS A97050)

2023-02-13

WIP

AMS4340H

1.1 Form This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches, incl (127.00 mm, incl) in nominal diameter or least thickness (see 8.4). 1.2 Application These products have been used typically for structural applications requiring high tensile properties and good exfoliation corrosion resistance, but usage is not limited to such applications.

Standard

Silver Alloy, Brazing Filler Metal 56Ag - 22Cu - 17Zn - 5.0Sn 1145 to 1205 °F (618 to 652 °C) Solidus-Liquidus Range

2023-01-17

CURRENT

AMS4763C

This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips, and a viscous mixture (paste) of powder in a suitable binder.

Standard

Silver Alloy, Brazing Filler Metal 54Ag - 40Cu - 5.0Zn - 1.0Ni 1325 to 1575 °F (718 to 857 °C) Solidus-Liquidus Range

2023-01-17

CURRENT

AMS4772L

This specification covers a silver alloy in the form of wire, rod, sheet, strip, foil, pig, powder, shot, and chips and a viscous mixture (paste) of powder in a suitable binder.

Standard

Tolerances Copper and Copper Alloy Bars and Rods

2023-01-17

CURRENT

AMS2221H

This specification covers established inch/pound manufacturing tolerances applicable to bars and rods of copper and copper alloys ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range.

Standard

Copper, Sheet, Strip, and Plate, Soft Annealed

2022-12-18

WIP

AMS4500L

This specification covers unalloyed copper in the form of sheet, strip, and plate at least 0.015 inch (0.38 mm) in nominal thickness.