Search Results

This paper describes a measurement points' placement technique for the sound source identification using inverse acoustic analysis. In order to reduce noise in NVH problem for various kinds of machines including small size engine, it is necessary to identify the sound source. The inverse acoustic analysis is a technique that is effective for the sound source identification.[1,2] The inverse acoustic analysis identifies a surface vibration of an object by measuring the radiated sound and solving the inverse problem. Nakano et al. researched about the location of sound pressure measurement points for accurate improvement.[3] They clarified that the sound pressure measurement points on the concentric circle gave more accurate surface vibration than the measurement points on the square lattice.

Early studies on the tire vibration characteristics of road noise focused on radial modes of vibration because these modes are dominant in vertical spindle force. However, recent studies of Noise, Vibration and Harshness (NVH) prediction have suggested that tire modeling not only of radial modes, but also of lateral vibration, including lateral translational and lateral bending modes, affect interior noise. Thus, it is important to construct tire dynamic models with few degrees of freedom for whole-vehicle analysis of NVH performance. Existing tire dynamics model can't express tire lateral vibrations. This paper presents a new approach for tire vibration analysis below 200Hz, and a formula for tire natural frequencies. First, a tire dynamic model is developed based on the thin cylindrical shell theory. Kinetic and potential energies are derived. Mode shape function is also derived by the assumption of inextensility in the neutral of the tread ring.

This paper describes an identification of a sound source model for a diesel engine installed on an agricultural machine by Inverse-Numerical Acoustic analysis (INA), and the applicability of the identified sound source model. INA is a method to identify surface vibrations from surrounding sound pressures. This method is applicable for a complicated-shaped sound source like an engine. In order to confirm the accuracy of the identified sound source model, the surface vibrations of the engine are compared with the measured results. Moreover, in the condition of the simulated engine room, the surrounding sound pressure levels of the engine are predicted using the sound source model and the boundary element method (BEM). For the verification of the prediction accuracy, the surrounding sound pressures of the engine are measured using the testing device which simulated actual engine room, namely an enclosure.

This paper describes a prediction of vibration and the transfer path analysis (TPA) using an engine multi body dynamics (MBD) model and measured frequency response functions (FRFs). TPA is used in order to analyze each contribution of vibration transfer paths. In the TPA, input forces from vibration source to passive part should be identified accurately. In the traditional TPA, an identification of input forces is done using only experimental results. Therefore, a parametric study to an improvement of a structure or an isolation system is impossible. In this study, the MBD model of engine is constructed, and input forces from engine to mainframe of agriculture machine are predicted. The accuracy of prediction is confirmed, compared with the results from the traditional TPA method. The contribution of each transfer path is analyzed, and the vibration levels of operator position are predicted using the measured FRFs and the simulated input forces.

Researches for automation of hydraulic excavators have been conducted for laborsaving, improved efficiency of operations and increased worker's safety improvement. Authors' final goal is to develop automatic digging system which can realize the high efficiency. Therefore, it is thought that appropriate digging control algorithm is important for the automation. For this goal, this paper shows a dynamics model of the backhoe excavator and simulations using such models. Detailed dynamic models are needed from the point of view of the control engineering. Authors evaluate effectiveness of automatic digging algorithm by simulation models. In this research, the linkage mechanism which contains the closed loops is modeled based on the Newton-Euler formulation, where motion equation is derived. Moreover, we apply a soil model for simulation, based on the two dimensional distinct element method (DEM), in order to reproduce reaction force from grounds.

Researches for automated construction machinery have been conducted for labor-saving, improved work efficiency and worker's safety, where a tracking control function was proposed as one of the key control system strategies for highly automated productive hydraulic excavators. An optimized digging trajectory that assures as much soils scooped as possible and less energy consumption is critical for an automated hydraulic excavator to improve work efficiency. Simulation models that we used to seek an optimized digging trajectory in this study consist of soil models and front linkage models of a hydraulic excavator. We developed two types of soil models. One is called wedge models used to calculate reaction forces from soils acting on a bucket during digging operation, based on the earth pressure theory. The other is called Distinct Element Method (DEM) model used to analyze soil behaviors and estimate amounts of soils scooped and reaction forces quantitatively.

The demand to reduce noise in the passenger cars is increasing. Tire vibration characteristics must be considered when studying road noise because of the strong interaction between tire vibration characteristics and interior car noise. Car manufacturers are keenly interested in studies on the prediction of NVH (Noise, Vibration and Harshness) performance, including viewing tires as substructure. Recently, studies have illustrated the effect that tire lateral bending mode have has on road noise, while most past studies of tire vibration focused on the circumference mode, which excited the vertical spindle force. Therefore, further study of tire lateral bending mode is necessary. Modeling of the tire lateral bending mode is described in this paper. First, lateral spindle force is measured under tire rolling conditions. Second, experimental modal analysis is performed to grasp tire lateral bending mode. Finally, a tire vibration model is built using the cylindrical shell theory.

Road noise is one of the main vehicle interior noises. To minimize this, it is necessary to reveal the vibration characteristics of a rolling tire. Tire vibration has complex behavior due to tire contact with the road and rolling. In an earlier study, we clarified the effect of contact patch restriction for tire vibration characteristics in the non-rolling condition using the tire dynamical model. However, mode shapes were identified with circumferential wave number. Therefore, it is difficult to clarify the effect for tire vibration in the contact and rolling condition. In this paper, we will apply the receptance method, which is used as an analysis of the rotating disc and gear pair for the tire model toward the tire vibration analysis in the contact and rolling condition. Furthermore, the validity of the approach using this method will be verified from comparison with the result of an earlier study.

The research into vibration characteristics of a loaded and rolling tire is essential for the prediction of spindle forces. There are tire vibration characteristics one of which is the first natural frequency of a loaded and rolling tire is lower than that of an unrolling tire. The vibration characteristics, for a loaded and rolling tire, are affected by the effect of rotation, restrictions of the vibration due to road contact, and the behavior of rubber dependent on amplitude strain. The consideration of the degradation of natural frequency is therefore necessary in the tire model for prediction of spindle forces. This paper describes an identification method for the tire equivalent stiffness of a tire model focused on vertical spindle forces. The first mode is dominant in vertical spindle forces. First, the natural frequencies in rolling and unrolling tires are identified by operational impact test.

This paper presents progressive techniques based on the previous SAE papers [1], [2] for vibration transmission analysis (VTA) on finite element (FE) model using Transfer Path Analysis (TPA). The techniques are: 1) a contribution calculation technique for structure with manifold and continuous transfer paths: 2) a visualization technique of the influence degree for efficient derivation of measures for response reduction. In VTA, influence degree of each DOF is calculated based on TPA. In order to understand characteristics of vibration transmission (VT) easily and visually by engineers, magnitude of influence degree is expressed by replacement to magnitude of displacement in the diagram of FE vibration shape. This visualization technique is applied to an automotive body structure. The proposed techniques are applied to automotive body structure consisting of members and panels. The members are such as pillars, cross members and side members, which are the main VT paths.

A high performance digging algorithm for a hydraulic excavator has not been established because the relationship between digging parameters and digging performance is complex. An examination process for a high-performance digging algorithm is proposed. In this paper, the digging efficiency is defined as the soil volume derived by the applied energy to drive the bucket in order to evaluate digging performance. The digging algorithm, which we study for high digging efficiency, decreases the reaction force to the bucket from the soil by moving the bucket upward when the reaction force exceeds a threshold during digging. Digging tests are performed with a miniature test device and a simulation model by two-dimensional distinct element methods (2D-DEM). The device and the simulation assess the effectiveness of the digging algorithm. It is quantitatively shown that the digging performance obtained by the feedback digging system is improved to prevent growing of reaction force.

In this research, we aim at the construction of a steering cooperation-type front-wheel steering control system to reduce the rider's steering load by stabilizing the behavior of the motorcycle when turbulence in the direction of a roll occurs during low-speed driving. Finally, a front-wheel steering control system that considers cooperation with a rider's steering based on the experimental result is constructed, and the utility is verified by simulation.

This paper describes damping loss factor prediction in statistical energy analysis (SEA) for co-generation system (CGS) enclosures. To accurately predict vibration and noise by SEA, it is important to estimate parameters called the damping and coupling loss factors. In this study, the damping loss factors were estimated by the decay ratio method and a technique for calculating the modal damping ratio that uses a multi-degree of freedom curve fit. The calculated loss factor was applied to the vibration prediction of the co-generation system, and the influence of the internal loss factor calculation method on prediction accuracy was verified.

This paper describes the relationship between the rider's evaluation of feeling of pulse and the seat vibration of the cruiser-type motorcycle. A simulated running condition was created to measure the seat vibration and engine speed. Next, the seat vibration was reproduced on the hydrodynamic shaker. Finally, we examined the influence of which order of rotational speed effects evaluation of feeling of pulse in a forced vibration test. As a result, it is known that 0.5th and 1st orders of seat vibration contribute to evaluation of feeling of pulse near 1,500 to 2,000 rpm of engine rotation.

This paper describes a proposal of techniques on Transfer Path Analysis (TPA) to analyze transmission of vibration among the components in a complex structure. This proposal is evolved from the previous one [1] in the dimension which dominates the quality of the analysis in automotive body structure by TPA. The proper coordinate transformation was introduced to resolve the troublesome process on the application of the body structure in the previous proposal. The complications are caused by the treatment with a lot of transfer functions and transmitted forces at the conjunctions that are complexly assembled with many adjacent nodes. Dimension of the analytical region is expanded from two to three in this study. That is, from the cross section of interface of components to the structure itself where the vibration transmits between two components.

Improvement of vehicle interior noise is desired in recent years in the modern world of the demand of low weight, good fuel economy and offering technical advantages strongly. The dynamic force transmission of rolling tires from the road surface to the spindles is a critical factor in vehicle interior noise. We focus on structure-borne noise transferred through the spindle. It is necessary for effort of the effective tire/road noise reduction to predict spindle force excited by tire/road contact. The major issues in predicting spindle forces are to clarify the distribution of road forces and how to input on the simulation model. Therefore, it is important that road forces are measured accurately on the rolling tire. First, the dynamic road forces on the rolling tire are measured by using the tri-axial force sensor directly. In efforts to reduce interior noise due to structure-borne noise, it is necessary to predict spindle forces excited by the tire/road contact.

This paper describes the application of statistical energy analysis (SEA) to predicting sound power radiated from co-generation system enclosure. To predict vibration and noise accurately by using SEA, it is important to estimate parameter called loss factors. In this study, loss factors were estimated by power injection method. Next, the noise radiated from enclosure surface was predicted by the obtained vibration and radiation efficiency of enclosure panels. As a result, the calculated sound power was relatively corresponding to measured sound power. Finally, the sound power from modified enclosure was predicted. Coupling loss factors related to a modified subsystem were estimated by ratio of the number of structure modes. By using these steps, the noise from the system was reduced.

It’ll be expected that tandem riders increase in the future. So, there is a need to improve the motorcycle stability of tandem riding from the perspectives of safety and comfort. In this research, we focus on tandem riding at low speed because the motorcycle especially becomes unstable. In order to improve the stability of a motorcycle after disturbance is input by the passenger’s posture change, we design a front wheel steer control system that assists the rider’s driving operation. And we simulate it. It is necessary to consider cooperation with the rider’s driving operation. In this study, as a means to consider the cooperative control of the man-machine system, the fuzzy logic was applied to this system.

This paper describes the application of inverse boundary element method (Inverse BEM) to vibration identification on surface of Co-generation System enclosure. This method is a kind of matrix inversion using singular value decomposition. Therefore it is significant to select proper tolerance in order to identify vibration accurately. In this study, the tolerance selection method is proposed. First step, the surface velocity of numerical model with unit input was obtained by Finite Element Method. The sound pressure around the model was obtained by BEM. Second step, random noise was mixed with obtained sound pressure. Third step, by using Inverse BEM, the surface velocity was identified from the sound pressure with noise. Next, the error between the identified velocity and the velocity obtained by FEM were evaluated and the tolerance is selected to minimize the error.

Current simulation of Noise, Vibration and Harshness (NVH) using Computer Aided Engineering (CAE) often uses a large DOF and detailed finite element model along with improvement of CAE technology and computational performance. By using a detailed model, predictions of precise vibration characteristics become possible. However, the number of eigenmodes in the target frequency range increases and engineers require a lot of time to examine eigenmodes and establish countermeasures. In this paper, a practical method of efficient and effective analysis by classifying target eigenmodes into a small number of groups is proposed. The classification is executed based on the relation between the dynamic characteristics of the entire automotive body structure and substructures.