Search Results

The enhancement of vortex development, fuel-air mixing and heat release in diesel spray flame by inversed-delta injection rate shaping, having been predicted via LES simulation with detailed chemical kinetics, is experimentally confirmed for the first time. Newly developed 3-injector TAIZAC (TAndem Injector Zapping ACtivation) injector realizing aggressive inversed-delta injection rate shaping was used for single-shot combustion experiments in a constant volume combustion vessel. Simultaneous high-speed (120,000fps) and high-resolution (1,280 x 704 pixels) laser schlieren and UV OH* chemiluminescence imaging combined with subsequent Flame Imaging Velocimetry (FIV) analysis was employed to elucidate the correlation between vortex development and enhanced heat release.

In order to explore the potential of thermal efficiency improvement of diesel engines with injection rate shaping, TAIZAC (TAndem Injectors Zapping ACtivation) injector consisting of commercially available two common-rail injectors was developed in-house. A simple architecture adopted for TAIZAC injector consists of an upper injector connected to a high pressure source, a lower injector injecting into the cylinder and sealing parts between the two injectors. A fast response piezo-actuated injector (G3P) was employed as the upper one with an additionally drilled large axial orifice for faster fuel supply. A solenoid-actuated injector (G4S) was employed as the lower one for its applicability to inner volume reduction by body cut.

In our previous work, diesel late combustion heat release is suspected to originate from rich fuel mixture cloud stagnating at the spray tip. Injection rate shaping is gaining attention as an attractive strategy to control diesel spray combustion characteristics where it could be an effective approach in reducing the late combustion. Progressive ramp-down injection rate as in “inversed-delta” shape is achieved by using a novel rate shaping injector called TAIZAC (TAndem Injectors Zapping Activation); rate shaping can be realized by controlling the actuation timing of two directly-connected commercially available injectors. To investigate the potential of inversed-delta rate shaping for reduction of diesel late combustion, simultaneous high-speed UV laser diffuse back illumination (DBI), UV emissions and soot luminosity imaging of inversed-delta and conventional rectangle-injected spray flames conducted in a constant volume combustion chamber are compared.

In recent years, trans-esterified vegetable oils have been widely applied to diesel engine in order to suppress greenhouse gas emissions. However, “neat” vegetable oils are expected to be directly used to resolve some difficulties faced in their use, such high viscosity and slightly high fuel consumption. In this study neat linseed oil has been investigated as a neat vegetable oil. It was found to show higher fuel consumption than diesel fuel, however at the same time it showed lower indicated fuel consumption than diesel fuel. These results suggest some increase in engine friction loss in a neat biofuel diesel engine. Studies have been extensively investigated the difference in friction loss and a newly developed “improved deceleration method” has been applied.

The purpose of this study is to explain the characteristics of homogeneous charge compression ignition. n-Heptane, which has the same cetane number as diesel fuel, was chosen for the fuel. A rapid compression machine was used to clarify the effects of air-fuel ratio, O2 concentration, and compression temperature on ignition delay and NOx emission. These investigations allowed the introduction of a formula for ignition delay.

NO, OH, and soot in combustion flame produced from burning at high temperature and pressure diesel fuel spray issuing from a single-hole injection nozzle was measured by laser induced fluorescence (LIF) and laser induced incandescence (LII) methods. The LIF images of OH showed that OH radical, distributed in a band-like zone outside the region of the flame luminescence observed, would persist even after the extinction of flame luminescence. The LIF images of NO showed that NO was located slightly outside the flame luminescence zone and that its region was almost the same as that of OH and would tended to increase in the latter period of the combustion process. Also, the LII images showed that the formation of soot would take place near the flame central zone coincident with the flame luminescence zone.

Methanol has a poor self-ignition property and thus requires some kind of ignition assist system. Our evaluation of two such systems, a spark-assisted type and a glow-assisted type, indicated that these systems had room for improvement in terms of combustion stability and thermal efficiency in the low-load range. Combustion improvements in the low-load range were therefore carried out by increasing the compression ratio, adopting an injection nozzle with multiple holes and providing an ignition chamber. This has resulted in the successful development of a glow-assisted methanol engine with full-load performance equivalent or superior to a base diesel engine and with lower NOx emission. For practical application of this engine, further improvements in durability and reliability are to be made.

To reduce exhaust emissions and fuel consumption, the effect of high pressure fuel injection was investigated with in-cylinder fuel spray observation and single cylinder engines. Spray impingement on the cavity wall promotes mixing with air and reduction in the nozzle area extends this wall impingement as a result of increasing both fuel injection pressure and injection period. There exists an optimum range for the injection period. Increased injection pressure by modifying injection rate of fuel pump and nozzle area, improves smoke and fuel consumption at low and medium speeds in particular. To extend these effects of high pressure injection, more optimized combustion system and minimized injection equipment drive torque must be required. To resolve the problem of high pressure injection such as higher combustion noise and increase in NOx emissions, the combination with pilot injection must be one of the most effective ways.