Search Results

The pursuit of flexibility is a recurring theme in engine design and development. Engines that are able to switch between the two-stroke operating cycle and four-stroke operation promise a great leap in flexibility. Such 2S-4S engines could then continuously select the optimum operating mode - including HCCI/CAI combustion - for fuel efficiency, emissions or specific output. With recent developments in valvetrain technology, advanced boosting devices, direct fuel injection and engine control, the 2S-4S engine is an increasingly real prospect. The authors have undertaken a comprehensive feasibility study for 2S-4S gasoline engines. This study has encompassed concept and detailed design, design analysis, one-dimensional gas dynamics simulation, three-dimensional computational fluid dynamics, and vehicle simulation. The resulting 2/4SIGHT concept engine is a 1.04 l in-line three-cylinder engine producing 230 Nm and 85 kW.

Controlled auto Ignition (CAI) combustion has great potential for reducing both NOx emissions and fuel consumption in IC engines and the application of direct injection technology to the CAI engine adds another dimension of control to the combustion process. In this work an air-assisted injection system was applied to an engine that used residual gas to initiate and control CAI combustion. Injections were performed at Exhaust valve closure (EVC), intake valve opening (IVO) and BDC of the intake/compression stroke and the effects on combustion phasing (i.e. ignition timing and burn duration), engine output, fuel consumption and exhaust emissions analyzed. Injection at EVC gave the best results in terms of engine output, operating range and combustion stability. Injection at IVO generally resulted in the lowest fuel consumption. It was found that injection timing is an effective means of controlling combustion phasing.

The paper reports an investigation into the HCCI/CAI combustion process in a single cylinder optical engine. The auto-ignition and combustion processes of primary reference fuels were studied using the two-dimensional PLIF technique as well as heat release analyses. The formaldehyde formed during the low-temperature reactions of HCCI/CAI combustion was visualized by a PLIF system. The formaldehyde was excited by a Nd:YAG laser pumped tunable dye laser at 355nm wavelength and detected by a gated ICCD camera. Both temporal and spatial distributions of formaldehyde were measured during the auto-ignition processes of different primary reference fuels. The results have shown that the formation of formaldehyde and its subsequent disappearance were closely related to the start of the low temperature and high temperature heat release processes, respectively. The formation of formaldehyde was more affected by the charge temperature than by the fuel concentration.

In general smoothing and evaluating an autobody outer surface is very difficult for autobody designers, but it is a very important requirement in autobody design. This paper reviewed a lot relevant researches, expressed the definition of autobody Class-A surface, and presented a new method for modeling. Finally some design examples were demonstrated.

Three-way catalytic converters used on spark ignition engines have performance and durability characteristics which are effected by the thermal environment in which these operate. The design of the exhaust system and the location of the catalyst unit are important in controlling the range of thermal states the catalyst is exposed to. A model of system thermal behaviour has been developed to support studies of these. The exhaust system is modelled as connected pipe and junction elements with lumped thermal capacities. Heat transfer correlations for quasi-steady and transient conditions have been investigated. The catalytic converter is treated as elemental slices in series. Exothermic heat release and heat exchange between the monolith, mat, and shell are described in the model. A similar description is applied to lean NOx trap units.

A correlation for total gas-side heat transfer rate has been derived from the analysis of engine data for measured heat rejection rate, frictional dissipation, and published data on exhaust port heat transfer. The correlation is related to the form developed by Taylor and Toong, and the analysis draws on this. However, cylinder and exhaust port contributions are separated. Two empirical constants are fixed to best match predicted to measured results for heat rejection to coolant and oil cooler under steady-state conditions, and also for exhaust port heat transfer rates. The separated contributions also defined a correlation for exhaust port heat transfer rate. The description of gas-side heat transfer is suited to needs for the analysis of global thermal behaviour of engines.

A suite of computer programs for engine thermal analysis and the analysis of thermal interactions with external systems has been developed. Defining an engine design is made particularly simple and the representation generated agrees well with measured data. Engine geometry, mass, and internal coolant volume are determined from a short list of key parameters and the selection of a generic template. Thermal conditions in the engine structure are modelled numerically using the lumped-capacity method. Heat exchange at boundaries with gas, coolant and oil flows are described through sub-models giving good agreement with data for global characteristics of engine behaviour. The effects of spark timing and coolant composition on heat transfer rates are taken into account, as is the effect of frictional dissipation as a heat source. Validation and applications of the model are described.

A method of predicting HC, CO and NOx emissions and fuel-used over drive cycles has been developed. This has been applied to FTP-75 and ECE+EUDC drive cycles amended to include cold-start and warm-up. The method requires only fully-warm steady state indicated performance data to be available for the engine. This is used in conjunction with a model of engine thermal behaviour and friction characteristics, and vehicle/drive cycle specifications enabling engine brake load/speed variations to be defined. A time marching prediction of engine-out emissions and fuel consumption is carried out taking into account factors which include high engine friction and poor mixture preparation after cold-start. Comparisons with experimental data indicate that fuel consumption and emissions can be predicted to quantitative accuracy. The method has been applied to compare and contrast the importance of various operating regimes during the two cycles.

An air-assisted fuel vaporiser (AAFV), designed to replace the conventional fuelling system has been tested on a 3.0-litre development engine under simulated cold-Start conditions. Providing the cold engine with pre-vaporised fuel removed the need for an enriched mixture during start-up. Comparisons between the AAFV and standard fuelling systems were performed. Engine-out hydrocarbon (HC) exhaust emissions were measured during cold-start and the ensuing two minutes. Fuel spray characterisation was also conducted using a steady flow test rig designed to mimic inlet port conditions of air flow and manifold pressure over a wide range of engine operation.

Engine Electronic Control (EEC) systems on spark ignition engines enable a high degree of performance optimisation to be achieved through strategy and calibration details in software, but development times and costs can be high. The range of functions performed by EEC systems, and the level of performance demanded, are increasing and new methods of development are required. In the paper, the use of neural networks in the development and implementation of open-loop control of air/fuel ratio during engine transient operating conditions is described. The investigation has addressed the definition of suitable networks, the procedure and data required to train these, and assessment of real-time performance of the implemented system. The potential benefits of the approach include reduced calibration effort and simplification of the control strategy.

The rate of heat rejection to the coolant system of an internal combustion engine depends upon coolant composition, among other factors, because this influences the coolant side heat transfer coefficient. The correlation developed by Taylor and Toong for heat transfer rate has been modified to account for this effect. The modification retains the gas-to-coolant passage thermal resistance implicit in the original correlation. The modified correlation gives predictions in agreement with experimental data. Compared to 100% water, mixtures of 50% ethylene glycol/50% water lower heat rejection rates by typically 5% and up to 25% in the extreme. This depends upon local conditions in the coolant circuit, which can give rise to different heat transfer regimes. Application of the modified correlation is outlined and illustrated.

The cycle-by-cycle variation of heat transferred per cycle (q) to the combustion chamber surfaces of spark ignition engines has been investigated for quasi-steady and transient conditions produced by throttle movements. The heat transfer calculation is by integration of the instantaneous value over the cycle, using the Woschni correlation for the heat transfer coefficient. By examination of the results obtained, a relatively simple correlation has been identified: This holds both for quasi-steady and transient conditions and is on a per cylinder basis. The analysis has been extended to define a heat flux distribution over the surface of the chamber. This is given by: where F(x/L) is a polynomial function, q″ is the heat transfer per cycle per unit area to head and piston crown surfaces and gives the distribution along the liner

A computational model has been developed to support investigations of temperature, heat flow and friction characteristics, particularly in connection with warm-up behaviour. A lumped capacity model of the engine block and head, empirically derived correlations for local heat transfer and friction losses, and oil and coolant circuit descriptions form the core of the model. Validation of the model and illustrative results are reported.

Two methods of determining the rate of heat transfer from the combustion chamber have been investigated. A First Law analysis is shown to be ill-conditioned because of sensitivity to heat release and gas property calculations. An alternative approach equates cycle-averaged chamber heat transfer to the difference between heat rejected to the coolant and gas heat transfer to the exhaust port. This has been examined as a basis for calibrating the Woschni correlation.

Knock in a spark-ignition engine was characterized in terms of its occurrence and magnitude or intensity. Cylinder pressure data from 90 consecutive individual cycles were generated from a single-cylinder engine of disc chamber design at about 72kHz sampling rate over a range of operating conditions between no knock and 100% of the cycles knocking. Mean values and distribution of following parameters were analysed: knock occurrence crank angle, knock intensity, combustion rate and the end-gas thermodynamic state. The effects of fuel octane number and inlet air temperature on these parameters were studied. The thermal imaging technique has been applied to record two-dimensional surface temperatures of cylinder head and piston simultaneously. The change in surface temperatures during knocking and non-knocking cycles was thus studied. As expected, increase in the inlet air temperature or decrease in the fuel octane number caused the knock onset to occur at less advanced spark timing.

The warm-up characteristics of a spark-ignition engine significantly affect fuel consumption and emissions from cars. A thermal imaging technique has been applied to measure the cylinder head surface temperature and piston surface temperature of an internal combustion engine simultaneously. The two-dimensional thermal images of the cylinder head surface temperature were viewed through an infra-red transmitting window mounted in the piston. The piston surface temperature was measured by painting black two small areas of the window's top surface. The similar thermal characteristics of the window material (silicon) to those of a normal piston and good heat transfer between the window and the piston provided realistic operation conditions. The mean and extreme values of the inlet valve, exhaust valve, two other areas of the cylinder head surface and window surface temperatures were measured from the thermal images during the first two minutes of the engine start.

Increasing pressure on lowering vehicle exhaust emissions to meet stringent California and Federal 1993/1994 TLEV emission standards of 0.125 gpm NMOG, 3.4 gpm CO and 0.4 gpm NOx and future ULEV emission standards of 0.04 gpm NMOG, 1.7 gpm CO and 0.2 gpm NOx has focused specific attention on the cold start characteristics of the vehicle's emission system, especially the catalytic converter. From test data it is evident that the major portion of the total HC and CO emissions occur within the first two minutes of the driving cycle while the catalyst is heating up to operating temperature. The use of an electrically heated catalyst (EHC) has been proposed to alleviate this problem but the cost and weight penalties are high and the durability has yet to be fully demonstrated (1)*. This paper describes a method of reducing the light-off time of the catalytic converter to less than 20 seconds by means of an afterburner.

A thermal imaging system has been developed for viewing and recording the cylinder head surface temperatures of an internal combustion engine. The system consists of an I.R scanner, associated calibration and image processing equipment and an infra-red transmitting window mounted in the piston. The infrared window material used (silicon) has thermal characteristics close to those of a normal piston. The two dimensional temperature distribution of a cylinder head surface has been measured during start-up. The imaging results from the camera were checked against the readings from the thermocouples fitted into the cylinder head. The agreement was very good, and gives confidence in the system.

The Rassweiler and Withrow method for determining mass fraction burnt from S.I. engine cylinder pressure data is widely used, but implementation details vary. The best form of implementation, and the effect of uncertainties in the assumptions made, have been investigated. Attention has been given to determining the end of combustion, the effect of signal noise on the pressure data, the effect of assumptions regarding the value and variation of apparent compression and expansion polytropic indices and, particularly, how these should be determined. The treatment of late burning cycles is also discussed. Versatile software has been developed for idle to full load studies with good tolerance to signal noise.

A novel technique, using a ‘flying’ Hot Wire Anemometer is described; it is shown how the turbulent structure in a motored engine, using a high molecular weight gas as the working fluid, may be investigated with relative simplicity and very little engine modification. Initial results are presented for integral and micro length scales, which are within the range expected based on previous work.