Search Results

The bio-fuel, 2,5 - dimethylfuran (DMF) is currently regarded as a potential alternative fuel to gasoline due to the development of new production technology. However, little is known about the flame behavior in an optical engine. In this paper, high speed imaging (with intensifier) was used during the combustion of DMF and its blends with gasoline and ethanol (D50, D85, E50D50 and E85D15) in an SI optical engine. The flame images from the combustion of each fuel were analyzed at two engine loads: 3bar and 4bar IMEP. For DMF, D50 and E50D50, two modes were compared: DI and PFI. The average flame shapes (in 2D) and the average flame speeds were calculated and combined with mass fraction burned (MFB) data. The results show that when using DMF, the rate of flame growth development and flame speed is higher than when using gasoline. The differences in flame speed between DMF and gasoline is about 10% to 14% at low IMEP.

The new fuel, 2, 5-dimenthylfuran, known as DMF, captured worldwide attention since the discovery of its new production method. As a potential bio-fuel, DMF is competitive to gasoline in many areas, such as energy density, combustion efficiency and emissions. However, little work has been performed on its unconventional combustion mode. In this work, high speed imaging and thermal investigation are carried out to study DMF and gasoline dual-injection on a single cylinder, direct injection spark ignition optical engine. This dual-injection strategy combines direct injection (DI) and port fuel injection (PFI) simultaneously which means two different fuels can blend in the cylinder with any ratio. It provides a flexible way to use bio-fuels with gasoline. DMF DI with gasoline PFI and ethanol DI with gasoline PFI are studied under different injection proportions (by volume) and IMEPs.

This paper focuses on supercharged HCCI engines employing internal EGR that is obtained by the use of negative valve overlap. In HCCI engines, the absence of throttling coupled with the use of high compression ratio to facilitate auto-ignition and with the use of lean mixtures result in improved fuel efficiency. High dilution is required to control the auto-ignition and it also results in reduction of the production of NOx. To compensate for the charge dilution effect, the method used to recover the loss of power is to introduce more air in to the engine which allows introducing also more fuel while maintaining high lambda. A supercharger is required to introduce the required amount of air into the engine. The modelling investigation performed with Ricardo WAVE® coupled with CHEMKIN® and experimental investigation for supercharged HCCI show significant improvement in terms of extension of load range and reduction of NOx over the naturally aspirated HCCI and also over SI operation.

This paper presents a modeling study of a gasoline HCCI engine using a single-zone and a multi-zone engine combustion models coupled with the CHEMKIN chemical kinetics solver for the closed part of the cycle. These combustion models are subsequently combined with a 1-D gas dynamics engine cycle simulation code which calculates the engine gas exchange to supply the boundary conditions for the in-cylinder simulation and also predicts engine performance. The simulated in-cylinder pressure history and charge composition at the time of exhaust valve opening are compared with the data from a parallel engine experimental project. Although the single-zone model is useful for parameter studies by predicting the trend of auto-ignition timing variations as the result of the effect of engine operating conditions, the matching of simulated and test data is good perhaps only if the mixture and temperature distributions in the cylinder are uniform.

Negative valve overlapping is widely used for trapping residual burned gas within the cylinder to enable controlled Homogeneous Charge Compression Ignition (HCCI). HCCI has been shown as a promising combustion technology to improve the fuel economy and NOx emissions of gasoline engines. While the importance of in-cylinder flow in the fuel and air mixing process is recognised, the characteristics of air motion with specially designed valve events having reduced valve lift and durations associated with HCCI engines and their effect on subsequent combustion are not yet fully understood. This paper presents an investigation in an optical engine designed for HCCI combustion using EGR trapping. PIV techniques have been used to measure the in-cylinder flow field under motored conditions and a quantitative analysis has been carried out for the flow characterisation with comparison made against the flow in the same engine with conventional valve strategies for SI combustion.

The major characteristics of the combustion in Homogeneous Charge Compression Ignition (HCCI) engines, irrespective of the technological strategy used to enable the ‘controlled auto-ignition’, are that the mixture of fuel and air is preferably premixed and largely homogeneous. Ignition tends to take place simultaneously at multiple points and there is no bulk flame propagation as in conventional spark-ignition (SI) engines. This paper presents an experimental study of flame development in an optical engine operating in HCCI combustion mode. High resolution and high-speed charge coupled device (CCD) cameras were used to take images of the flame during the combustion process. Fuels include gasoline, natural gas (NG) and hydrogen addition to NG all at stoichiometric conditions, permitting the investigation of combustion development for each fuel. The flame imaging data was supplemented by simultaneously recorded in-cylinder pressure data.

This paper presents a one-dimensional model for heat transfer in exhaust systems. Convective heat transfer in pipe flows under steady-state and transient conditions is studied. Analytical solution of the governing equation for steady-state condition is obtained. Effects of turbulent, laminar and transition flow regimes on heat transfer are allowed for. Influences of various parameters, i.e. inlet mass flow rate & temperature, wall temperature, pipe length and pipe diameter, on heat transfer are assessed quantitatively. Efforts are made to explain the physics of heat transfer process from basic principles. It is proven mathematically that in turbulent flow regime, the pipe outlet temperature increases with increasing pipe diameter and mass flow. For transient condition, the governing equations are derived, and a warm-up process is simulated. Effects of inlet condition, pipe geometry, external heat transfer and wall thickness on outlet temperature are discussed.

While Homogeneous Charge Compression Ignition (HCCI) is a promising combustion mode with significant advantages in fuel economy improvement and emission reductions for vehicle engines, it is subject to a number of limitations, for example, hardware and control complexity, or NOx and NVH deterioration near its operating upper load boundary, diminishing its advantages. Conventional spark-ignition combustion mode is required for higher loads and speeds, thus the operating conditions near the HCCI boundaries and their corresponding alternatives in SI mode must be studied carefully in order to identify practical strategies to minimise the impact of the combustion mode transition on the performance of the engine. This paper presents the results of an investigation of the combustion mode transitions between SI and HCCI, using a combination of an engine cycle simulation code with a chemical kinetics based HCCI combustion code.

Extensive simulation was carried out to investigate cam strategies for SI engine part load operation. Performance of the engine with dual independent variable cam timing (VCT) system is assessed. Over a wide range of part load operating conditions, engine performance parameters, such as fuel consumption, were expressed in forms of contour maps as a function of intake and exhaust cam timings. Based upon the simulation results, cam timings were optimized for various part load conditions. A cam strategy incorporating intake and exhaust cam retard was developed to improve fuel economy and emissions. Influences of intake and exhaust cam timing on the gas-exchange and combustion processes were also analyzed. It was shown that the fuel economy improvement by dual independent VCT is achieved primarily through reduction of pumping loss. Effects of in-cylinder charge motion and the use of differential intake cam profiles on fuel economy were examined.

A single zone combustion model based on a chemical kinetic solver has been combined with a one-dimension thermo/gas dynamic engine simulation code to study the operating characteristics of a V6 engine in which Homogeneous Charge Compression Ignition (HCCI) operation (also referred to as ‘Controlled Auto-ignition” CAI) is enabled by a cam profile switching (CPS) system with negative valve overlap. An operational window within which HCCI combustion is possible has been identified and the limit of HCCI operating region for varied valve lift possibilities is explored. The mechanisms and potential fuel economy improvements within the HCCI envelope are studied and modelled results compared against data from similar engines. It is shown that for the best fuel economy the valve timing strategy needs to be selected very carefully, despite the engine's capability to operate at a range of valve timing combinations.

High-speed cine photography has been applied to an optically-accessed version of a modern 4-valve, pent-roof, si engine in order to observe the behaviour of fuel under cold starting and warm-up conditions. A wall film was formed on the combustion chamber surface in the vicinity of the valves when fuel was supplied by pintle and disk-type injectors. This wall film survived combustion but was drawn into the exhaust system when the exhaust valves opened. The use of an air-blast atomiser avoided the formation of this wall film, but some wetting of the piston was apparent, as it was with the other types of injector.