Search Results

Diesel particulate filters (DPF) are a common component in emission-control systems of modern clean diesel vehicles. Several DPF materials have been used in various applications. Silicone Carbide (SiC) is common for passenger vehicles because of its thermal robustness derived from its high specific gravity and heat conductivity. However, a segmented structure is required to relieve thermal stress due to SiC's higher coefficient of thermal expansion (CTE). Cordierite (Cd) is a popular material for heavy-duty vehicles. Cordierite which has less mass per given volume, exhibits superior light-off performance, and is also adequate for use in larger monolith structures, due to its lower CTE. SiC and cordierite are recognized as the most prevalent DPF materials since the 2000's. The DPF traps not only combustible particles (soot) but also incombustible ash. Ash accumulates in the DPF and remains in the filter until being physically removed.

Ammonia Selective Catalytic Reduction (SCR) and Lean NOx Trap (LNT) systems are key technologies to reduce NOx emission for diesel on-highway vehicles to meet worldwide tighter emission regulations. In addition DeNOx catalysts have already been applied to several commercial off-road applications. Adding the DeNOx catalyst to existing Diesel Oxidation Catalyst (DOC) and Diesel Particulate Filter (DPF) emission control system requires additional space and will result in an increase of emission system back pressure. Therefore it is necessary to address optimizing the DeNOx catalyst in regards to back pressure and downsizing. Recently, extruded zeolite for DeNOx application has been considered. This technology improves NOx conversion at low temperature due to the high catalyst amount. However, this technology has concerned about strength and robustness, because the honeycomb body is composed of catalyst.

Back pressure of Diesel Particulate Filter (DPF) varies with accumulation of soot and/or ash. Soot can be cleaned in a high temperature oxidation (regeneration) process. But ash which is incombustible particulate matter derived from lubricant oil, engine wear, etc. cannot be cleaned from DPF without mechanical ash removal process and influences the back pressure perpetually. Design and control of DPF involving variation of the back pressure with ash accumulation will provide further improvement of fuel consumption and reliable operation in extended vehicle life time. Nevertheless, empirical investigations concerning ash accumulation are few because of the long testing time due to the slow accumulation rate, i.e. 0.5 - 2mg/mile [19]. In this investigation, four different designs of Cordierite (Cd) DPF were subjected to an accelerated ash accumulation test which is utilizing artificial ash powder.

Ash accumulation is a considerable factor for long-term Diesel Particulate Filter (DPF) performance. Ash accumulation reduces the open frontal area (OFA) and plugs the surface pores. As a result, DPF back pressures with no soot (hereinafter “initial DPF back pressure”) rise. At the same time, DPF back pressures with soot (hereinafter “sooted DPF back pressure”) fall [ 1 , 2 , 3 , 4 ]. Then sooted DPF back pressures rise after the reductions of the certain ranges [ 1 , 3 , 4 ]. It is known that DPF back pressure behaviors change variously by ash loading like this. The understanding of DPF back pressure behaviors with ash accumulation is indispensable for proper after-treatment system management. Ash accumulation progresses slowly and gradually in DPF while using of vehicles. Because of the slowness, the field surveys require a few years at least.

To evaluate various Diesel Particulate Filter (DPF) efficiently, accelerated tests are one of effective methods. In this study, a simulator composed by diesel fuel burners is proposed for fundamental DPF evaluations. Firstly particle size distribution measurement, chemical composition and thermal analysis were carried out for the particulate matter (PM) generated by the simulator with several combustion conditions. The PMs generated by specific conditions showed similar characteristics to PMs of a diesel engine. Through these investigations, mechanism of PM particle growth was discussed. Secondly diversified DPFs were subjected to accelerated pressure drop and filtration efficiency tests. Features of DPFs could be clarified by the accelerated tests. In addition, the correlation between DPF pressure drop performance and PM characteristics was discussed. Thirdly regeneration performance of the simulator's PM was investigated.