Search Results

Diesel oxidation catalyst and particulate filter technologies are well established and their applications are well known. However, there are certain limitations with both technologies due to their inherent technical characteristics. Both technologies get 75-90% reduction of HC and CO. A typical oxidation catalyst can be applied to almost any heavy duty diesel application and achieve 20 to 30% reduction in PM mass but no significant reduction in the number of PM particles. On the other hand, diesel particulate filters are very effective at removing >90% of the particles by mass and >99% by number. Unfortunately, passive DPF technology cannot be applied to all applications since the filter regeneration is limited by engine out NOx to PM ratio as well as exhaust temperature. For this reason, particulate filters can not universally be applied to older “dirtier” engines with high PM emissions.

The application of oxidation catalyst and particulate filter technology for the reduction of particulate matter (PM), hydrocarbons (HC) and carbon monoxide (CO) emissions from heavy duty diesel engines has become an established practice. The design and performance of such systems have been commercially proven to the point that the application of these technologies is cost effective and durable. The application of an effective NOx reduction technology in heavy duty diesel applications is more complicated since there are no passive NOx reduction technologies that can be fit onto HDD vehicles. However, Selective Catalytic Reduction (SCR) systems using Urea injection to achieve NOx reduction have become the technology of choice in Europe and have been applied to achieve Euro IV emissions levels on new HDD vehicles. In addition, retrofit SCR emission control systems have also been developed that can provide high NOx reduction when applied on existing HDD vehicles.

The retrofitting of diesel engines with oxidation catalyst and particulate filter technology for the reduction of particulate matter (PM), hydrocarbons (HC) and carbon monoxide (CO) emissions has become an established practice. The design and performance of such systems have been commercially proven to the point that the application of these technologies is a cost effective means for states to effectively meet pollution reduction goals. One of the reasons that these technologies are so widely applied is because they can be sized and fitted based on easily measurable vehicle parameters and published engine emission information. These devices generally work passively with basic temperature and back pressure monitoring devices being used to alert the operator to upset conditions. The application of an effective NOx reduction technology in similar retrofit installation, is more complicated. There are no passive NOx reduction technologies that can be retrofit onto HDD vehicles.

The New York State Department of Environmental Conservation (DEC) and Environment Canada have jointly participated along with partners the New York City Metropolitan Transit Agency (MTA); Johnson Matthey, Environmental Catalysts & Technologies; Equilon Enterprises, LLC and Corning, Inc. in a project to evaluate the effect of various combinations of fuels and aftertreatment configurations on diesel emissions. Emissions measurements were performed during engine dynamometer testing of an International DT 466E heavy-duty diesel engine. Fuels tested in the study were Diesel Fuel 1 and 2, low sulfur diesel (150 ppm), two ultralow sulfur fuels (<30 ppm), Fischer-Tropsch, Biodiesel, PuriNOx™ and two Ethanol-Diesel blends. Configurations tested were: engine out, and diesel oxidation catalyst, continuously regenerating diesel filter, and exhaust gas recirculation aftertreatment. In general, the use of more aggressive aftertreatment (ie.

With growing concerns about NOx and particulate matter (PM) emissions from diesel engines, stricter regulations are being implemented which require advanced emission control technology. This paper discusses the combination of a diesel particle filter system (DPF) with a low pressure exhaust gas re-circulation (EGR) system to provide four way emission control of NOx, PM, CO and HC from existing heavy duty diesel engines. The combined EGR-DPF system has been used in Europe over the past 4 years, with over 1200 systems installed on urban buses and other on-road applications. This system has shown 40-60% NOx reduction in addition to >90% CO, HC and PM reductions. Recently, several field trial programs have been initiated to evaluate the performance and durability of this EGR-DPF system under US operational conditions. These include retrofit applications on urban buses and on construction trucks.

In urban areas, particulate emission from diesel engines is one of the pollutants of most concern. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled, “Clean Diesel Vehicle Air Quality Project” has been initiated by NY City Transit under the supervision of NYSDEC and with active participation from several industry partners. Under this program, 25 NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter systems and have been operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9 month period for operations, maintainability and durability of the particulate filter.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. With increasing worldwide regulatory requirements to lower particulate matter (PM) standards for heavy duty diesel powered vehicles, the interest in diesel particulate filter based emission control solutions such as the Continuously Regenerating Technology (CRT®) have significantly increased. This system has been applied to thousands of heavy-duty diesel vehicles in Europe over the last six years to meet various local and governmental requirements, while recently introduced in the US. Among the numerous demonstration programs taking place in the US, one important one is the evaluation of CRT filter systems on urban transit buses in NY City. Here, several NY City transit buses with DDC Series 50 engines have been equipped with CRT filters and operating on ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000.

Particulate emission control from diesel engines is one of the major concerns in the urban areas in California. Recently, regulations have been proposed for stringent PM emission requirements from both existing and new diesel engines. As a result, particulate emission control from urban diesel engines using advanced particulate filter technology is being evaluated at several locations in California. Although ceramic based particle filters are well known for high PM reductions, the lack of effective and durable regeneration system has limited their applications. The continuously regenerated diesel particulate filter (CRDPF) technology discussed in this presentation, solves this problem by catalytically oxidizing NO present in the diesel exhaust to NO2 which is utilized to continuously combust the engine soot under the typical diesel engine operating condition.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled “Clean Diesel Demonstration Program” has been initiated by NY City Transit under the supervision of NY State DEC and with active participation from several industrial partners. Under this program, several NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter system and are operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses are being evaluated over a 8-9 month period for operations, maintainability and durability of the particulate filter.

The EPA implemented the Urban Bus Retrofit/Rebuild (UBRR) Program for transit buses built before 1994 in an effort to lower the amount of PM emissions in densely populated urban areas. The objective of the program is to provide certified emission control technologies that reduce PM emissions from older buses by 25% or to below 0.1 g/bhp-hr. This paper reviews the development of a retrofit kit that has been certified under the UBRR program to meet the 0.1 g/bhp-hr PM emission requirements on DDC 6V92TA engines with both mechanical (MUI) and electronic (DDEC) fuel injection controls. The kit is a combination of specific and modified engine parts and a catalytic exhaust after-treatment device. The kit replaces existing parts with a new camshaft, a uniquely configured cylinder kit and specified turbocharger, blower and injector. For the MUI engines the cam timing, injector height and fuel modulator are set at specific values to achieve the lowest possible PM level.