Search Results

Future European air quality standards for light duty diesel vehicles will include stringent NOx emission regulations. In order to meet these regulations, a lean NOx catalyst system may be necessary. Since the catalytic removal of NOx is very difficult with the large concentration of oxygen present in diesel exhaust, a reductant is usually added to the exhaust to increase the NOx conversion. This paper describes a lean NOx catalyst system for a Transit light-duty truck which uses a reductant solution of urea in water. In this work, a microprocessor was used to vary the amount of the reductant injected depending on the operating conditions of a 2,5 L naturally aspirated HSDI engine. The NOx conversions were 60% and 80% on the current European driving cycle and the U.S. FTP cycles, respectively. Data on the emissions of HC, CO, NOx, particulate mass and composition, individual HC species, aldehydes, PAH and most HC species were evaluated.

The rapid heating of an under-body catalyst after cold start by combustion of rich engine products with added secondary air is described. The results of initial durability studies including spark plug fouling, oil dilution and thermal shock are presented, together with emissions performance and a mileage accumulation study. Also discussed are failure mode assessment and the system tolerance to anticipated open-loop errors and real-world driving scenarios.

Particulate and manganese mass emissions have been measured as a function of mileage for four Escort and four Explorer vehicles using 1) MMT (Methylcyclopentadienyl Manganese Tricarbonyl) added to the gasoline at 1/32 g Mn/gal and 2) gasoline without MMT. The MMT was used in half of the fleet starting at 5,000 miles. The vehicles were driven on public roads at an average speed of 54 mph to accumulate mileage. This report describes the particulate and manganese emissions, plus emissions of four air toxics at 5,000, 20,000, 55,000, 85,000 and 105,000 miles. Four non-regulated emissions were measured and their average values for vehicles without MMT were 0.6 mg/mi for formaldehyde, 0.7 mg/mi for 1,3-butadiene, 9 mg/mi for benzene and 12 mg/mi for toluene. Corresponding values for MMT-fueled vehicles were between 1.5 and 2.4 times higher.

Vehicle emissions have been measured and the results statistically evaluated for a vehicle test fleet consisting of four Escorts and four Explorers using both a fully formulated durability fuel doped with methylcyclopentadienyl manganese tricarbonyl (MMT) at 1/32 gram Mn/gallon and the same fully formulated durability fuel without the MMT. The fleet was divided in half -- half with MMT and half without MMT doped fuel. This report covers emission measurement results at 5,000; 15,000; 50,000 and 100,000 miles of exposure to MMT doped fuel. A modified paired t-test is used to analyze the emission data obtained from all the fleet vehicles. The statistical evaluation of both feedgas and tailpipe emissions indicate that the use of MMT is detrimental to emissions of HC at the 15,000 mile; 50,000 mile and 100,000 mile levels of MMT exposure. As mileage is accumulated, the pronounced the effect on HC by the fuel additive MMT.

Prototype metallic and electrically heated metallic catalysts (EHC) are being evaluated on a gasoline fueled vehicle. The vehicle used for this evaluation is a 5.0L Mustang equipped with an emissions control system which includes mass air, and sequential electronic fuel injection (SEFI). FTP tests are performed to evaluate non-heated metallic and electrically heated metallic catalysts in both production and close-coupled configurations. The objective of the evaluation is to determine light-off characteristics of both the non-heated metallic and the EHCs and their effect on cold-start emissions (Bag 1). FTP results are compared to those obtained from conventional ceramic catalysts in the same configurations. Initial data show some emissions benefits for the prototype EHC converter during the first 60 seconds or so of the FTP. From 60 seconds on in the FTP cycle, the ceramic catalyst was slightly more efficient, leading to overall FTP emissions about the same for the two systems.