Search Results

Li-ion batteries are commonly used in Electric Vehicles (EVs) due to its high-power density and higher life cycle performance. Individual cells in such battery packs may sometimes lead to thermal runaway conditions under the effect of localized heat generation and faults. Battery liquid cooling methods are normally being employed to resolve this problem with limitations of limited temperature operating range and difficulty in reaching the intricate spaces between the cells. Introducing phase change material (PCM) can mitigate these limitations. The present study deals with a detailed numerical study of a single (Li-ion) cell in ANSYS Fluent using multi-scale multi dimension (MSMD) - Newman, Tiedenann, Gu and Kim (NTGK) model. The single cell model is investigated for the evaluation of its temperatures at varying air velocity surrounding the cell at higher C-rating (load) values.

Butanol is a potential alternative fuel for diesel in compression ignition (CI) engines. Many of the physico-chemical properties of butanol such as low carbon-to-hydrogen (C/H) ratio compared to diesel, higher heating value, lower heat of vaporization and suitable density-viscosity values compared to ethanol and methanol makes it suitable as an alternative fuel. However, poor cetane number and miscibility are the limitations associated with butanol. The use of fuel additives as ignition improver could be beneficial in overcoming the issues associated with alcohols. In this work, an experimental investigation in a twin-cylinder CI engine was carried out to assess the effect of doped cetane improving additives (Diethyl ether (DEE), Diglyme (DEGME) and Ethyl diglyme (DEGEE)) for diesel-butanol blend (B15).

Diesel engines are lucrative in terms of high thermal efficiency and low specific fuel consumption. The major drawbacks of these engines are high NOx and particulate matter (PM) emissions due to heterogeneous combustion. In the current emissions norms (BS-VI), a limit for particle number concentration is also introduced. There are few numerical studies investigating the soot particle size and number characteristics at different engine operating conditions. In this work, a parametric numerical study is conducted to investigate the effect of engine operating parameters on PM characteristics such as number density, size, and volume fraction. Simulations were performed using the Reynolds Averaged Navier Stokes equation with renormalization group K-ε turbulence model available in ANSYS FORTE CFD software.

Rapid population growth and fuel crisis due to limited availability of fossil fuels, led the research in the fields of alternative fuel for the replacement of conventional fuels. The petroleum-like characteristics of ethanol make it an excellent alternative fuel for the internal combustion (IC) engines. It can be easily derived from waste agricultural resources such as plant biomass and forest residue, ease of production increases the possibility of its utilization locally in the agricultural engine and transport vehicles. A laboratory experiment was carried out, using a common rail direct injection (CRDI) diesel engine at varying load conditions (no-load, 20 Nm and 40 Nm) with two ethanol blends (5% and 10% v/v indicated by E05 and E10) and diesel (D100) to explore the combustion stability, combustion behaviour and emissions parameters of ethanol in existing compression ignition (CI) engine.

Diesel engines are one of the most important power generating units these days. Increasing greenhouse gas emission level and the need for energy security has prompted increasing research into alternative fuels for diesel engines. Biodiesel is the most popular among the alternatives for diesel fuel as it is biodegradable and renewable and can be produced domestically from vegetable oils. In recent years, hydrotreated vegetable oil (HVO) has also gained popularity due to some of its advantages over biodiesel such as higher cetane number, lower deposit formation, storage stability, etc. HVO is a renewable, paraffinic biobased alternative fuel for diesel engines similar to biodiesel. Unlike biodiesel, the production process for HVO involves hydrogen as catalyst instead of methanol which removes oxygen content from vegetable oil.

Diesel particulates are mainly composed of elemental carbon (EC) and organic carbon (OC) with traces of metals, sulfates and ash content. Organic fraction of the particulate are considered responsible for its carcinogenic effects. Diesel oxidation catalyst (DOC) is an important after-treatment device for reduction of organic fraction of particulates. In this study, two non-noble metal based DOCs (with different configurations) were prepared and evaluated for their performance. Lanthanum based perovskite (LaMnO3) catalyst was used for the preparation of DOCs. One of the DOC was coated with support material ceria (5%, w/w), while the other was coated without any support material. Prepared DOCs were retrofitted in a four cylinder water cooled diesel engine. Various emission parameters such as particulate mass, particle number-size distribution, regulated and unregulated emissions, EC/OC etc., were measured and compared with the raw exhaust gas emissions from the prepared DOCs.

Diesel engines are very efficient prime movers in their power range. Fuel is directly injected into the combustion chamber. Performance and emission characteristics of diesel engines are highly influenced by the fuel spray parameters and atomization of the injected fuel. As the emission regulations become stringent, it is very important to optimize the combustion in internal combustion engines for different fuels including alternative fuels. Spray visualization using optical techniques play a very important role to analyze macroscopic spray parameters and fuel atomization behavior. In the present experimental study, an important alternative CI engine fuel, Karanja oil and its blends with diesel have been investigated for their spray parameters and fuel atomization relative to mineral diesel. These parameters are different for the two fuels because of difference in the viscosity and density of the fuels.