Search Results

Diesel fuels usually comprise a wide range of compounds having different molecular structures which can affect both the fuel's physical properties and combustion characteristics. In future, as synthetic fuels from fossil and sustainable sources become increasingly available, it could be possible to control the fuel's molecular structure to achieve clean and efficient combustion. This paper presents experimental results of combustion and emissions studies undertaken on a single cylinder diesel engine supplied with 18 different fuels each comprising a single, acyclic, non-oxygenated hydrocarbon molecule. These molecules were chosen to highlight the effect of straight carbon chain length, degree of saturation and the addition of methyl groups as branches to a straight carbon chain.

Current developments in fuels and emissions regulations are resulting in increasingly severe operating environment for the injection system. Formation of deposits within the holes of the injector nozzle or on the outside of the injector tip may have an adverse effect on overall system performance. This paper provides a critical review of the current understanding of the main factors affecting deposit formation. Two main types of engine test cycles, which attempt to simulate field conditions, are described in the literature. The first type involves cycling between high and low load. The second involves steady state operation at constant speed either at medium or high load. A number of influences on the creation of deposits are identified. This includes fouling through thermal condensation and cracking reactions at nozzle temperatures of around 300°C. Also the design of the injector holes is an influence, because it can influence cavitation.

There is a great deal of interest in new technologies to assist in reducing the CO2 output of passenger vehicles, as part of the drive to meet the limits agreed by the EU and the European Automobile Manufacturer's Association ACEA, itself a result of the Kyoto Protocol. For the internal combustion engine, the most promising of these include gasoline direct injection, downsizing and fully variable valve trains. While new types of spray-guided gasoline direct injection (GDI) combustion systems are finally set to yield the level of fuel consumption improvement which was originally promised for the so-called ‘first generation’ wall- and air-guided types of GDI, injectors for spray-guided combustion systems are not yet in production to help justify the added complication and cost of the NOx trap necessary with a stratified combustion concept.

The piston bowl design is one of the most important factors that affect the air/fuel mixing and the subsequent combustion and pollutant formation processes in a direct injection diesel engine. The bowl geometry and dimensions, such as pip region, bowl lip area, and torus radius are all known to have an effect on the in-cylinder mixing and combustion process. In order to understand better the effect of torus radius, three piston bowls with different torus radius and lip shapes designs but with the same lip area and pip inclination were investigated using Computational Fluid Dynamics (CFD) engine modelling. KIVA3V with improved sub-models was used to model the in-cylinder flows and combustion process, and it was validated on a High-Speed Direct Injection (HSDI) engine with a 2nd generation common rail fuel injection system.

Reductions in fuel consumption, noise level, and pollutant emissions such as, Nitrogen Oxide (NOX) and Particulate Matter (PM), from direct-injection (DI) diesel engines are important issues in engine research. To achieve these reductions, many technologies such as high injection pressure, multiple injection, retarded injection timing, EGR, and high swirl ratio have been used in high-efficiency DI diesel engines in order to achieve combustion and emission control. However, each technology has its own advantages and disadvantages, and there is a very strong interaction between these methods when they are simultaneously used in the engine. This study presents a computational study of both the individual effect and their interactions of injection timing, EGR and swirl ratio separately and their interaction in a HSDI common rail diesel engine using the KIVA-3V code.

Controlled Auto-Ignition (CAI) combustion, also known as HCCI or PCCI, has recently emerged as a viable alternative combustion process to the conventional spark ignition (SI) or compression ignition (CI) process for internal combustion (IC) engines, owing to its potential for high efficiency and extremely low emissions. One of the most effective and practical means of achieving CAI combustion in an engine is to retain or recycle the burnt gases. In order to understand better the effects of recycled burnt gases on CAI combustion, detailed analytical and experimental studies have been carried out. The analytical studies were performed using an engine simulation model with detailed chemical kinetics. The five effects of the recycled burned gases studied include: (1.) Charge heating effect: higher intake charge temperature due to hot burned gases; (2.) Dilution effect: the reduction of oxygen due to the presence of the burned gases; (3.)

A quantitative relationship between diesel soot oxidation rate and oxidation temperature and oxygen partial pressure was investigated by burning the diesel exhaust soot particles in a controlled flat flame supplied with methane/air/oxygen/nitrogen mixtures. The oxidation temperature and the oxygen partial pressure were controlled in the ranges of 1530 to 1820 K and 0.01 to 0.05 atm (1atm = 1.01325 bar) respectively. Soot particle size distribution measurements were achieved with transmission electron microscopy (TEM) for particle samples that were collected on copper grids at different positions along the flame centerline. Oxidation periods were determined by means of laser Doppler anemometry (LDA). The experimental results showed that the experimental oxidation rates fall between the values predicted by the Nagle and Strickland-Constable formula and those by the Lee formula.

The effects of Exhaust Gas Recirculation (EGR) on diesel engine exhaust emissions were isolated and studied in earlier investigations (1,2,3,4,5). This paper analyses the heat release patterns during the combustion process and co-relates the results with the exhaust emissions. The EGR effects considered include the dilution of the inlet charge with CO2 or water vapour, the increase in the inlet charge temperature, and the thermal throttling arising from the use of hot EGR. The use of diluents (CO2 and H2O), which are the principal constituents of EGR, caused an increase in ignition delay and a shift in the location of start of combustion. As a consequence of this shift, the whole combustion process was also shifted further towards the expansion stroke. This resulted in the products of combustion spending shorter periods at high temperatures which lowered the NOx formation rate.

This paper is a complementary to previous investigations by the authors (1,2,3,4) on the different effects of EGR on combustion and emissions in DI diesel engine. In addition to the several effects that cold EGR has on combustion and emissions the application of hot EGR results in increasing the inlet charge temperature, thereby, for naturally aspirated engines, lowering the inlet charge mass due to thermal throttling. An associated consequence of thermal throttling is the reduction in the amount of oxygen in the inlet charge. Uncooled EGR, therefore, affects combustion and emissions in two ways: through the reduction in the inlet charge mass and through the increase in inlet charge temperature. The effect on combustion and emissions of increasing the inlet charge temperature (without reducing the inlet charge mass) has been dealt with in ref. (1).

Water vapour is a main constituent of exhaust gas recirculation (EGR) in diesel engines and its influence on combustion and emissions were investigated. The following effects of the water vapour were examined experimentally: the effect of replacing part of the inlet charge oxygen (dilution effect), the effect of the higher specific heat capacity of water vapour in comparison with that of oxygen it replaces (thermal effect), the effect of dissociation of water vapour (chemical effect), as well as the overall effect of water vapour on combustion and emissions. Water vapour was introduced into the inlet charge, progressively, so that up to 3 percent of the inlet charge mass was displaced. This was equivalent to the amount of water vapour contained in 52 percent by mass of EGR for the engine operating condition tested in this work.

This paper deals with the effects on diesel engine combustion and emissions of carbon dioxide and water vapour the two main constituents of EGR. It concludes the work covered in Parts 1, 2, and 3 of this series of papers. A comparison is presented of the different effects that each of these constituents has on combustion and emissions. The comparison showed that the dilution effect was the most significant one. Furthermore, the dilution effect for carbon dioxide is higher than that for water vapour because EGR has roughly twice as much carbon dioxide than water vapour. On the other hand, the water vapour had a higher thermal effect in comparison to that of carbon dioxide due to the higher specific heat capacity of water vapour. The chemical effect of carbon dioxide was, generally, higher than that of water vapour.

This is a first of a series of papers describing how the replacement of some of the inlet air with EGR modifies the diesel combustion process and thereby affects the exhaust emissions. This paper deals with only the reduction of oxygen in the inlet charge to the engine (dilution effect). The oxygen in the inlet charge to a direct injection diesel engine was progressively replaced by inert gases, whilst the engine speed, fuelling rate, injection timing, total mass and the specific heat capacity of the inlet charge were kept constant. The use of inert gases for oxygen replacement, rather than carbon dioxide (CO2) or water vapour normally found in EGR, ensured that the effects on combustion of dissociation of these species were excluded. In addition, the effects of oxygen replacement on ignition delay were isolated and quantified.

This is the second of a series of papers on how exhaust gas recirculation (EGR) affects diesel engine combustion and emissions. It concentrates on the effects of carbon dioxide (CO2) which is a principal constituent of EGR. Results are presented from a number of tests during which the nitrogen or oxygen in the engine inlet air was progressively replaced by CO2 and/or inert gases, whilst the engine speed, fuelling rate, injection timing, inlet charge total mass rate and inlet charge temperature were kept constant. In one set of tests, some of the nitrogen in the inlet air was progressively replaced by a carefully controlled mixture of CO2 and argon. This ensured that the added gas mixture had equal specific heat capacity to that of the nitrogen being replaced. Thus, the effects of dissociated CO2 on combustion and emissions could be isolated and quantified (chemical effect).

The extraction of small quantities of gas and particulates from diesel engine cylinders allows time-resolved gas and particulate analysis to be performed outside the engine during a short window of a few degrees crank angle at any stage of the engine cycle. The paper describes the design features and operation of a high-speed, intermittent sampling valve for extracting in-cylinder gases and particulates from diesel engines at any selected instant of the combustion process. Various sampling valve configurations are outlined. Detailed analysis of gas flow through the valve and the performance of the electromagnetic actuator and plunger are given in order to facilitate the design of the sampling valve. Finally, examples of the uses of the sampling valve in a direct-injection diesel engine are provided. These demonstrate how gaseous emissions such as NOx, uHC, CO2, and particulate emissions can be sampled at any part of the combustion process and analysed.

A programme of work is being undertaken to improve the performance of a spark-ignited natural gas engine, that has been converted from a diesel engine. The aim of this work is to reduce the fuel consumption and NOx emissions. All experimental data and predictions refer to full throttle operation at 1500 rpm. The work to be reported here will include baseline tests that have been used to calibrate a two-zone combustion model. Particularly important are the predictions of the NOx emissions. The simulation has then been used to predict the effects of using: a higher compression ratio, and a faster burn combustion system. The design philosophy of the resulting fast burn combustion system is discussed, and some preliminary results are presented. There will be a discussion of the ignition parameters that affect the lean burn operation, and the effect of the spark plug gap position is discussed in the context of results from a phenomenological model of turbulent combustion.

The influence of swirl on combustion in diesel and spark ignition engines is reviewed briefly, and this leads to a resumé of the swirl measuring techniques. The numerous ways of analysing swirl data are summarised and the relations between the different swirl parameters are presented. Experimental results are presented from a diesel engine in which the flow has been measured by a hot wire anemometer, a paddle wheel and a swirl torquemeter. The performance of the different measurement techniques is compared. Further results are presented (from a spark ignition engine) which illustrate the influence of the inlet port, manifold and entry conditions on the swirl measurements. Integration techniques are reviewed for producing a single swirl parameter to characterise the combined performance of the inlet port, valve and camshaft. Finally, the difficulty in standardising measurements of barrel swirl are discussed.

A variable compression ratio concept that can give a different expansion ratio to the compression ratio has been evaluated by means of a simulation of a turbocharged diesel engine. The VR/LE mechanism kinematics have been defined and described, and the compression ratio and expansion ratio have been presented as a function of the eccentric phase angle (αo). A zero-dimensional engine simulation that has been the subject of comprehensive validation, has been used as the basis of the VR/LE study. The effect of the compression ratio on the engine performance at fixed loads is presented. The principal benefits are a reduction in fuel consumption at part load of about 2%, and a reduction in ignition delay that leads to an estimated 6 dB reduction in combustion noise. The study has been conducted within the assumption of a maximum cylinder pressure of 160 bar.