Search Results

Small natural gas cogeneration engines frequently operate with lean mixture and late ignition timing to comply with NOx emission standards. Late combustion phasing is the consequence, leading to significant losses in engine efficiency. When substituting a part of the excess air with exhaust gas, heat capacity increases, thus reducing NOx emissions. Combustion phasing can be advanced, resulting in a thermodynamically more favourable heat release without increasing NOx but improving engine efficiency. In this work, the effect of replacing a part of excess air with exhaust gas was investigated first in a constant volume combustion chamber. It enabled to analyse the influence of the exhaust gas under motionless initial conditions for several relative air-fuel ratios (λ = 1.3 to 1.7). Starting from the initial value of λ, the amount of CH4 was maintained constant as a part of the excess air was replaced by exhaust gas.

Spark ignited engines with direct injection (DISI) in fuel stratified mode promise an increase in efficiency mainly due to reduced pumping losses at part load. However, the need for expensive lean NOx catalysts may reduce this advantage. Therefore, a Bowl-Prechamber-Ignition (BPI) concept with flame jet ignition was developed to ignite premixed lean mixtures in DISI engines. It is characterised by a combination of a prechamber spark plug and a piston bowl. An important feature of the concept is its dual injection strategy. A pre injection in the inlet stroke produces a homogeneous lean mixture with an air fuel ratio of λ = 1.5 to λ = 1.7. A second injection with a small quantity of fuel is directed towards the piston bowl during the compression stroke. The enriched air fuel mixture of the piston bowl is transported by the pressure difference between main combustion chamber and prechamber into the prechamber.

An operation with a lean air-fuel mixture enables smaller cogeneration gas engines to operate at both high efficiency and low NOx emissions. Conventionally, the combustion process is induced through spark ignition. However, its small reactive mixture volume sets limits on increasing the air-fuel ratio, as a higher dilution reduces mixture inflammability as well as flame propagation speed. In addition, the spark plug durability is limited due to electrode wear, particularly through spark erosion, causing high maintenance costs. The ignition by means of a hot surface has great potential to extend the frequency of servicing intervals as well as to improve the trade-off between engine efficiency and NOx emissions. Compared to conventional spark ignition, ignition by means of a hot surface is achieved by accelerated combustion. The latter is produced by an increased initial reactive mixture volume.

In this paper, results of experimental and numerical investigations of stratified exhaust gas recirculation in a single-cylinder gasoline engine are presented. The engine was operated in spray guided direct injection mode. The radial exhaust gas stratification was achieved by a spatial and temporal separated intake of exhaust gas and fresh air. The spatial separation of both fluids was realized by specially shaped baffles in the inlet ports, which prevent an early mixing up to the inlet valves. The temporally separation was performed by impulse charge valves, with one for the fresh air and one for the exhaust gas. From various possible strategies for time-dependent intake of fresh air and exhaust gas, four different strategies for the exhaust gas stratification were examined.

Engines with gasoline direct injection promise an increase in efficiency mainly due to the overall lean mixture and reduced pumping losses at part load. But the near stoichiometric combustion of the stratified mixture with high combustion temperature leads to high NOx emissions. The need for expensive lean NOx catalysts in combination with complex operation strategies may reduce the advantages in efficiency significantly. The Bowl-Prechamber-Ignition (BPI) concept with flame jet ignition was developed to ignite premixed lean mixtures in DISI engines. The mainly homogeneous lean mixture leads to low combustion temperatures and subsequently to low NOx emissions. By additional EGR a further reduction of the combustion temperature is achievable. The BPI concept is realized by a prechamber spark plug and a piston bowl. The main feature of the concept is its dual injection strategy.

Given its ability to be combined with the three-way catalyst, the stoichiometric operation is significantly more attractive than the lean-burn process, when considering the increasingly severe NOx limit for cogeneration gas engines in Germany. However, the high temperature of the stoichiometric combustion results in increased wall heat losses, restricted combustion phasings (owing to knock tendency) and thus efficiency penalties. To lower the temperature of the stoichiometric combustion and thus improve the engine efficiency, exhaust gas recirculation (EGR) is one of the most effective means. Nevertheless, the dilution with EGR has much lower tolerance level than with excess air, which leads to a consequent drop in the thermal efficiency. In this regard, reducing the water vapor concentration in the recirculated exhaust gas and increasing the EGR reactivity are two potential measures that may extend the mixture dilution limit and result in engine efficiency benefits.

Mechanical systems accomplish their tasks better when enhanced with cyber technologies. With the rapidly escalating desire for high efficiency, optimization and flexibility, these physical systems ought to be integrated with cyber technologies that enhance exhaustive manipulation of resources and productivity. The gateway for such a synergetic integration can be referred to as digitalization. Details regarding the digitization of a High-altitude Simulation chamber are discussed thoroughly in this paper. The simulation chamber was originally designed and developed as a test bench to study the characteristics of alternative fuels used in the engines of handheld tools in different altitudes and thermal conditions. It encompasses all the possible realistic temperature variations with altitude raising to 3500m above sea level.

Cogeneration represents a key element within the energy transition by enabling a balancing of the long-term fluctuations of regeneratives. Regarding the expected increase of hydrogen share in natural gas pipelines in Germany, this work deals with investigations of hydrogen-associated advantages for the lean and stoichiometric operations of natural gas cogeneration engines, in relation to numerous challenges, such as the efficiency-NOx trade-off. Charge dilution is commonly regarded as one of the most effective ways for improving thermal efficiency of spark-ignition gas engines. While excess air serves as a diluent in the lean combustion process, stoichiometric combustion dilution may be obtained by exhaust gas recirculation (EGR). Combining hydrogen addition with mixture dilution is an appealing approach for a better handling of the efficiency-emissions trade-off.

A climate and altitude conditioning test bench was developed at the Institute of Energy Efficient Mobility (IEEM) of Karlsruhe University of Applied Sciences to evaluate the overall sustainability of using innovative biofuels in handheld power tools such as chainsaws, trimmers and blowers under any typical operating condition worldwide. The 6 m3 hermetically sealed and thermally insulated test chamber is large enough to fit the entire power tool. A two-stage refrigeration system with intake air drying and electric heating allows for realistic temperature conditions to be set in the test chamber, ranging from arctic cold to tropical heat (-28 to 45 °C). Altitudes of up to 3500 m above sea level can be simulated using a throttle valve at the inlet of the chamber and a pressure-controlled rotary screw compressor positioned downstream the test chamber outlet.

Electrical power and efficiency are decisive factors to minimise payoff time of cogeneration units and thus increase their profitability. In the case of (small-scale) cogeneration engines, low-NOx operation and high engine efficiency are frequently achieved through lean burn operation. Whereas higher diluted mixture enables future emission standards to be met, it reduces engine power. It further leads to poor combustion phasing, reducing engine efficiency. In this work, an engine concept that improves the trade-off between engine efficiency, NOx emissions and engine power, was investigated numerically. It combines individual measures such as lean burn operation, overexpanded cycle as well as a power- and efficiency-optimised intake system. Miller and Atkinson valve timings were examined using a detailed 1D model (AVL BOOST). Indicated specific fuel consumption (ISFC) was improved while maintaining effective compression ratio constant.

Small-scale cogeneration units (Pel < 50 kW) frequently use lean mixture and late ignition timing to comply with current NOx emission limits. Future tightened NOx limits might still be met by means of increased dilution, though both indicated and brake efficiency drop due to further retarded combustion phasing and reduced brake power. As an alternative, when changing the combustion process from lean burn to stoichiometric, a three-way-catalyst allows for a significant reduction of NOx emissions. Combustion timing can be advanced, resulting in enhanced heat release and thus increased engine efficiency. Based on this approach, this work presents the development of a stoichiometric combustion process for a small naturally aspirated single cylinder gas engine (Pel = 5.5 kW) originally operated with lean mixture. To ensure low NOx emissions, a three-way-catalyst is used.

Operating an Otto-Engine with hydrogen as fuel the probability of combustion anomalies like knocking, pre-ignition and backfiring increases significantly. Knocking is strongly dependent on the operating point, while the cause for preignition is still investigated. Literature as well as preliminary investigations to this work suggest that especially the spark plug has a significant influence on the occurrence of preignition and backfiring. Hence, the scope of this paper is to identify and understand the influence of the spark plug on preignition in order to reduce their occurrence and receive more mechanical power from the engine. In the first step, the operating conditions leading to preignition and backfiring are determined experimentally using a naturally aspirated single cylinder gas engine and a state-of-the-art prechamber spark plug.

Charge dilution in gasoline engines reduces NOx emissions and wall heat losses by the lower combustion temperature. Furthermore, under part load conditions de-throttling allows the reduction of pumping losses and thus higher engine efficiency. In contrast to lean burn, charge dilution by exhaust gas recirculation (EGR) under stoichiometric combustion conditions enables the use of an effective three-way catalyst. A pre-chamber spark plug with hot surface-assisted spark ignition (HSASI) was developed at the UAS Karlsruhe to overcome the drawbacks of charge dilution, especially under part load or cold start conditions, such as inhibited ignition and slow flame speed, and to even enable a further increase of the dilution rate. The influence of the HSASI pre-chamber spark plug on the heat release under EGR dilution and stoichiometric conditions was investigated on a single-cylinder gasoline engine.

In an era of urbanization and increasing focus on sustainable transport options, bicycles and e-bikes (especially pedelecs) have gained popularity as environmentally friendly alternatives to cars. In order to develop digital twins of bicycles and electric bicycles, in particular pedelecs, and to study the cyclist’s behaviour in interaction with the electric drivetrain, investigations were carried out on an automotive chassis dynamometer. Evaluation data for the pedelec and its drivetrain as well as the riding behaviour of different riders were obtained within driving cycles on the road and on the test bed.An AVL chassis dynamometer was used, which is originally designed to test motor vehicles with a maximum power output of up to 150 kW and a maximum speed of 200 km/h. The tests were performed in the “road load simulation mode”, which simulates the speed-dependent driving resistances of the test vehicle.

A large number of small size gas-fired cogeneration engines operate with homogenous lean air-fuel mixture. It allows for engine operation at high efficiency and low NOx emissions. As a result of the rising amount of installed cogeneration units, however, a tightening of the governmental emission limits regarding NOx is expected. While engine operation with further diluted mixture reduces NOx emissions, it also decreases engine efficiency. This leads to lower mean effective pressure, in particular for naturally aspirated engines. In order to improve the trade-off between engine efficiency, NOx emissions and mean effective pressure, numerical investigations of an alternative combustion process for a series small cogeneration engine were carried out. In a first step, Miller and Atkinson cycles were implemented by advanced or retarded inlet valve closing timings, respectively.

Lean burn operation allows small cogeneration engines to achieve both high efficiency and low NOx emissions. While further mixture dilution enables future emission standards to be met, it leads to retarded combustion phasing and losses in indicated engine efficiency. In the case of naturally aspirated engines, IMEP drops due to lower fuel fraction, increasing brake specific fuel consumption. In this work, an alternative engine configuration was investigated that improves the trade-off between engine efficiency, NOx emissions and IMEP. It combines well-established means such as Miller/Atkinson valve timing and optimised intake system for a single-cylinder cogeneration engine, operating with homogenous lean air-natural gas mixture. First, the engine configuration was analysed using a detailed 1D CFD model, implying a significant potential in reaching the project target.

In an effort to reduce both maintenance costs and NOx emissions of small cogeneration engines operated with natural gas, an alternative ignition system that allows stable operation at very lean homogeneous air-fuel mixtures has been developed. Combustion is induced by an electrically heated ceramic glow plug, whose temperature is controlled by an ECU. Adjusting hot surface temperature allows shifting the inflammation timing of the mixture and, therefore, the phasing of combustion in the engine cycle. The main aim of this work was to determine the effect of intake pressure and air-fuel ratio on the parameters of hot surface ignition (HSI) and understand which are the factors limiting stable HSI operation in terms of cycle-by-cycle variations.

Homogeneous charge compression ignition (HCCI) in natural gas fueled engines is thought to achieve high efficiency and low NOx emissions. While automotive applications require various load and speed regions, the operation range of stationary cogeneration engines is narrower. Hence, HCCI operation is easier to reach and more applicable to comply with future emission standards. This study presents computationally investigations of the auto-ignition ranges of a stationary natural gas HCCI engine. Starting from a detailed 1D engine cycle simulation model, a reduced engine model was developed and coupled to chemical kinetics using AVL Boost. Compression ratio, air-fuel ratio, internal EGR rate (iEGR) and intake temperature were varied for three different speeds, namely 1200, 1700 and 2200 rpm. Each examination includes a full factorial design study of 375 configurations. In the first step, the combustion was calculated using the GRI-mechanism 3.0 and a single zone combustion model.

Small natural gas cogeneration engines usually operate with lean mixture and late combustion phasing to comply with NOx emission standards, leading to significant losses in engine efficiency. Owing to water evaporation heat and high specific heat capacity of the water vapor, leads the water injection to cooling the combustion chamber charge, which enables earlier combustion phasing, higher compression ratio and thus higher engine efficiency. Therefore, water injection enables mitigating the tradeoff between NOx emissions and engine performance, without loss in engine efficiency. The intake port injection represents, because of the low required injection pressure and the simple injector integration, a cost-effective way to introduce water into the engine. Hence, the purpose of this work is to adapt the intake port water injection timing to the charge mixture flow conditions in the intake port.

The use of hydrogen as an alternative fuel to power cogeneration gas engines has been a research topic over the last few decades and has currently gained importance, even more due to current circumstances related to decarbonisation efforts for the energy supply. A significant part of the research done is focused on the topic of combustion diagnostics, which can be fulfilled through different methods. This work investigates the feasibility of the ion current sensing for a pure hydrogen fueled series natural gas cogeneration engine. For this purpose, a variation of the fuel composition (from 100% natural gas to 100% hydrogen) was carried out while maintaining the indicated mean effective pressure (IMEP) and the combustion phasing (CA50). This demonstrated that the efficiency increased monotonically as the hydrogen concentration rose. Simultaneously, the duration of the ion current signals gradually dropped but was still detectable at 100% hydrogen combustion.