Search Results

Two campaigns measuring on-road emissions of 23 VN-trucks on a randomly chosen driving cycle, consisting of 10 miles two-lane and 8 miles four-lane road were performed. The first, during October 2004, showed tailpipe NOx emissions on fleet average of 1.06 g/bhp-hr including the time the exhaust gas temperature was below 200°C. The second, during June 2005, showed tailpipe NOx emissions on fleet average of 1.13 g/bhp-hr including the time the exhaust gas temperature was below 200°C. Complementary measurements in a SET-cycle (13 point OICA-cycle) on a chassis dynamometer showed a tailpipe emission of 0.008 g PM per bhp-hr. Moreover, cost analysis show that the diesel fuel consumption remains unchanged whether the truck running on ULSD is equipped with a Combined Exhaust gas AfterTreatment System (CEATS) installed or not.

On-road emission measurements of 23 VN-trucks on a randomly chosen driving cycle, consisting of 10 miles two-lane and 8 miles four-lane road, showed tailpipe NOx emissions on fleet average of 0.96 g/bhp-hr, or 1.06 g/bhp-hr when including the time the exhaust gas temperature was below 200°C. Complementary measurements in a SET-cycle (13 point OICA -cycle) on a chassis dynamometer showed a tailpipe emission of 0.008 g PM per bhp-hr. Moreover, cost analysis show that the diesel fuel consumption remains unchanged whether the truck running on ULSD is equipped with a Combined Exhaust gas AfterTreatment System (CEATS) installed or not.

Diesel emissions legislation continues to tighten around the world, and Particulate Matter (PM) emissions are currently the focus of much attention. Diesel PM can be controlled using Diesel Particulate Filters (DPFs), which can effectively reduce the level of carbon (soot) emissions to ambient background levels. In the Heavy Duty Diesel (HDD) area, the Continuously Regenerating Trap (CRT®) [1] has been widely applied in the retrofit market. This system will henceforth be referred to as the Continuously Regenerating DPF (CR-DPF). There are currently over 100,000 of these systems in use in retrofit applications worldwide. This system comprises a specially formulated Diesel Oxidation Catalyst (DOC) upstream of a DPF; the NO2 generated by the DOC is used to combust the carbon collected in the DPF at low temperatures. A model describing the performance of the CR-DPF has been developed.

The modern Diesel engine is one of the most versatile power sources available for mobile applications. The high fuel economy and power of the Diesel engine has long made it the choice for heavy-duty applications worldwide. Over the coming years, global emissions legislation applied to heavy-duty Diesel (HDD) engines will become more and more stringent, necessitating the use of advanced emissions control technologies. In particular, the coming exhaust gas emissions legislation focuses on particulate matter (PM) emissions and emissions of nitrogen oxides (NOx). A filtration device can control PM emissions, and a possible technology for the abatement of NOx emissions involves NOx absorber catalysts. This paper describes investigations into the activity and system behaviour of a prototype HDD exhaust system based on NOx absorber technology. The system consists of a “single leg” containing NOx absorber catalyst that is bypassed during rich regeneration of the NOx absorbers.

The retrofitting of diesel engines with oxidation catalyst and particulate filter technology for the reduction of particulate matter (PM), hydrocarbons (HC) and carbon monoxide (CO) emissions has become an established practice. The design and performance of such systems have been commercially proven to the point that the application of these technologies is a cost effective means for states to effectively meet pollution reduction goals. One of the reasons that these technologies are so widely applied is because they can be sized and fitted based on easily measurable vehicle parameters and published engine emission information. These devices generally work passively with basic temperature and back pressure monitoring devices being used to alert the operator to upset conditions. The application of an effective NOx reduction technology in similar retrofit installation, is more complicated. There are no passive NOx reduction technologies that can be retrofit onto HDD vehicles.

A 1-D numerical model describing the ammonia selective catalytic reduction (SCR) de-NOx process has been developed based on data measured on a laboratory microreactor for a vanadia-titania washcoated catalyst system. Kinetics for various NH3-NOx reactions were investigated, as well as those for ammonia, CO and hydrocarbon oxidation. The model has been successfully validated against engine bench measurements, over light-off and ESC tests, under a wide range of conditions, e.g. flow rate, temperature, NO2/NO ratio, and ammonia injection rate. A very good agreement between the experimental data and the model has been achieved. The model has now been used to predict the effect of NO2/NO ratio on NOx conversion, and the effect of different ammonia injection rates on the efficiency of the SCR process.

The tightening of Heavy Duty Diesel (HDD) emissions legislation throughout the world is leading to the development of emission control devices to enable HDD engines to meet the new standards. NOx and Particulate Matter (PM) are the key pollutants which these emission control systems need to address. Diesel Particulate Filters (DPFs) are already in use in significant numbers to control PM emissions from HDD vehicles, and Selective Catalytic Reduction (SCR) is a very promising technology to control NOx emissions. This paper describes the development and performance of the Compact SCR-Trap system - a pollution control device comprising a DPF-based system (the Continuously Regenerating Trap system) upstream of an SCR system. The system has been designed to be as easy to package as possible, by minimising the total volume of the system and by incorporating the SCR catalysts on annular substrates placed around the outside of the DPF-based system.