Search Results

Knowledge of fuel mass injected in an individual cycle is important for engine performance and modelling. Currently direct measurements of fuel flow to individual cylinders of an engine are not possible on-engine or in real-time due to a lack of available appropriate measurement techniques. The objective of this work was to undertake real-time Coriolis fuel flow measurement using GDI injectors on a rig observing fuel mass flow rate within individual fuel injections. This paper evaluates the potential of this technology - combining Coriolis Flow Meters (CFMs) with Prism signal processing together known as Fast Next Generation Coriolis (Fast NGC), and serves as a basis for future transitions on-engine applications. A rig-based feasibility study has been undertaken injecting gasoline through a GDI injector at 150 bar in both single shot mode and at a simulated engine speeds of 1788 and 2978 rpm. The results show that these injections can, in principle, be observed.

For efficiency, the majority of modern diesel engines implement multiple injection strategies, increasing the frequency of transient injection phases and thus, end of injection (EOI) events. Recent advances in diagnostic techniques have identified several EOI phenomena pertinent to nozzle surface wetting as a precursor for deposit formation and a potential contributor towards pollutant emissions. To investigate the underlying processes, highspeed optical measurements at the microscopic scale were performed inside a motored diesel engine under low load/idling conditions. Visualisation of the injector nozzle surface and near nozzle region permitted an indepth analysis of the post-injection phenomena and the behaviour of fuel films on the nozzle surface when the engine is not fired. Inspection of the high-speed video data enabled an interpretation of the fluid dynamics leading to surface wetting, elucidating the mechanisms of deposition and spreading.

Rail pressures of modern diesel fuel injection systems have increased significantly over recent years, greatly improving atomisation of the main fuel injection event and air utilisation of the combustion process. Continued improvement in controlling the process of introducing fuel into the cylinder has led to focussing on fluid phenomena related to transient response. High-speed microscopy has been employed to visualise the detailed fluid dynamics around the near nozzle region of an automotive diesel fuel injector, during the opening, closing and post injection events. Complementary computational fluid dynamic (CFD) simulations have been undertaken to elucidate the interaction of the liquid and gas phases during these highly transient events, including an assessment of close-coupled injections.

An unmodified, conventionally fuelled, 2009 Class D vehicle with a 2.0L turbocharged gasoline direct injection engine was operated on a range of gasoline, gasoline-ethanol and gasoline-butanol fuel blends over NEDC drive cycles and WOT power curves on a chassis dynamometer. Engine performance, engine management system parameters and vehicle out emissions were recorded to investigate the response of a current state-of-the-art technology vehicle to various alcohol fuel blends. The vehicle fired on all fuels and was capable of adapting its long term fuelling trim to cope with the increased fuel flow demand for alcohol fuels up to E85. Over the NEDC tests, the volumetric fuel consumption was very strongly related to the calorific content of the fuel. CO and NOx emissions were largely unaffected for the mid alcohol blends, but CO emissions decreased and NOx emissions increased significantly for the high alcohol fuels. THC emissions were largely unaffected.

The formation and breakup of diesel sprays was investigated experimentally on a common rail diesel injector using a long range microscope. The objectives were to further the fundamental understanding of the processes involved in the initial stage of diesel spray formation. Tests were conducted at atmospheric conditions and on a rapid compression machine with motored in-cylinder peak pressures up to 8 MPa, and injection pressures up to 160 MPa. The light source and long range imaging optics were optimized to produce blur-free shadowgraphic images of sprays with a resolution of 0.6 μm per pixel, and a viewing region of 768x614 μm. Such fine spatial and temporal resolutions allowed the observation of previously unreported shearing instabilities and stagnation point on the tip of diesel jets.

This work was concerned with evaluation of the performance and emissions of potential future biofuels during advanced spark ignition engine operation. The fuels prepared included three variants of gasoline, three gasoline-ethanol blends and a gasoline-butanol fuel altogether covering a range of oxygen mass concentrations and octane numbers to identify key influencing parameters. The combustion of the fuels was evaluated in a turbocharged multi-cylinder direct fuel injection research engine equipped with a standard three-way catalyst and an external EGR circuit that allowed use of either cooled or non-cooled EGR. The engine operating effects studied at both part and boosted high load conditions included fuel injection timing and pressure, excess air tolerance, EGR tolerance and spark retard limits. A number of blends were also mapped at suitable sites across the European drive cycle under downsized engine conditions.

Two optical techniques together with a CFD simulation have been used to study the interaction of intake airflow with the injected fuel spray in a motored direct injection gasoline engine. The combustion chamber was of a pent-roof construction with the side-mounted injector located low down between the inlet valves injecting at a 54° angle to the cylinder axis. The two-dimensional piston bowl shape allowed optical access for the Mie scatter technique to be used to investigate the liquid fuel behaviour in the central axial plane of the cylinder lying midway between the two inlet valves and passing through the centre line of the injector nozzle. A second set of images was obtained using backlighting, this time looking through the glass cylinder liner directly towards the injector. The in-cylinder simulation was run using the VECTIS software. Measurements and simulations were conducted for a range of early SOI timings between 20° and 80° ATDC.

To meet the future low emission targets for Diesel engines, engineers are optimising both the fuel injection and after treatment systems fitted to Diesel engines. In order to optimise the fuel injection system there is a need to characterize the fuel spray for a given injection nozzle geometry and injection pressure/duration. Modern Diesel common rail systems produce very dense sprays, making in-cylinder investigation particularly difficult. In this study the measurement of droplet sizes and velocities in dense Diesel sprays has been investigated using Phase Doppler Anemometry (PDA). PDA has been proven to be a valuable technique in providing an understanding of the structure and characteristics of liquid sprays in many studies. It is often applied to finely atomised and dispersed particle flows.

For optimum efficiency, the direct injection (DI) gasoline engine requires two operating modes to cover the full load/speed map. For lower loads and speeds, stratified charge operation can be used, while homogeneous charge is required for high loads and speeds. This paper has focused its attention on the latter of these modes, where the performance is highly dependent on the quality of the fuel spray, evaporation and the air-fuel mixture preparation. Results of quantitative and qualitative Laser Induced Fluorescence (LIF) measurements are presented, together with shadow-graph spray imaging, made within an optically accessed DI gasoline engine. These are compared with previously acquired air flow measurements, at various injection timings, and with engine performance and emissions data obtained in a fired single cylinder non-optical engine, having an identical cylinder head and piston crown geometry.

The performance of a direct injection gasoline engine (G-DI) is highly dependent on the quality of the air-fuel mixture preparation. This is of particular importance when operating at a stratified charge condition, where the ideal mixture distribution would be a stoichiometric region around the spark plug, surrounded by air. To achieve this ideal situation over a wide range of speeds and loads is extremely difficult, requiring an understanding of the fuel spray, the in-cylinder air motion and their interactions. This paper presents the results of Phase Doppler Anemometry (PDA) and Laser Induced Fluorescence (LIF) measurements made both within an optically accessed direct injection gasoline engine and under atmospheric conditions. The experimental results are compared with those of a VECTIS Computational Fluid Dynamics (CFD) simulation of the same engine.