Search Results

The subject of this paper is the reduction of the particle number emissions of a gasoline DI engine at high engine load (1.4 MPa IMEP). To reduce the particle number emissions, several parameters are investigated: the large scale charge motion (baseline configuration, tumble and swirl) can be varied at the single cylinder engine by using inlays in the intake port. The amount of residual gas can be influenced by the exhaust backpressure. By using a throttle valve, the exhaust backpressure can be set equal to the intake pressure and hence simulate a turbocharger's turbine in the exhaust system or the throttle valve can be wide open and thus simulate an engine using a supercharger. Additionally, higher fuel injection pressure can help to enhance mixture formation and thus decrease particulate formation. Therefore, a solenoid injector with a maximum pressure of 30 MPa is used in this work.

Small gasoline engines are used in motorcycles and handheld machinery, because of their high power density, low cost and compact design. The reduction of hydrocarbon emissions and fuel consumption is an important factor regarding the upcoming emission standards and operational expenses. The scavenging process of the two-stroke engine causes scavenging losses. A reduction in hydrocarbon emissions due to scavenging losses can be achieved through inner mixture formation using direct injection (DI). The time frame for fuel vaporization is limited using two-stroke SI engines by the high number of revolutions. A high pressure DI system was used to offer fast and accurate injections. An injection pressure of up to 140 MPa was provided by a common rail system, built out of components normally used in automotive engineering. A standard electromagnetic injector is applied for the fuel injection. This injection unit is dimensioned for multi-point injections in diesel engines.

The two-stroke SI engine is the predominant driving unit in applications that require a high power-to-weight ratio, such as handheld power tools. Regarding the latest regulations in emission limits the main development area is clearly a further reduction of the exhaust emissions. The emissions are directly linked to the combustion processes and the scavenging losses. The optimization of the combustion processes, which represents one of the most challenging fields of research, is still one of the most important keys to enhance the thermal efficiency and reduce exhaust emissions. Regarding future emission regulations for small two-stroke SI engines it is inevitable that the emissions of gases causing the greenhouse effect, like carbon dioxide, need to be reduced. As most small SI engines are carburetted and operate open loop, the mixture formation and the amount of residual gas differs from cycle to cycle [1].

The combustion processes optimization is one of the most important factors to enhancing thermal efficiency and reducing exhaust emissions of combustion engines [1; 2]. Future emission regulations for small two-stroke SI engines require that the emissions of gases causing the greenhouse effect, such as carbon dioxide, to be reduced. One possible way to reduce exhaust gas emissions from two-stroke small off-road engines (SORE) is to use biogenic fuels. Because of their nearly closed carbon dioxide circuit, the emissions of carbon dioxide decrease compared to the use of fossil fuels. Also biogenic fuels have a significant influence on the combustion process and thus the emissions of different exhaust gas components may be reduced. Besides greenhouse gases, several other exhaust gas components need to be reduced because of their toxicity to the human health. For example, aromatic hydrocarbons cause dangerous health problems, and can be reduced by using alkylate fuel.

The emission behaviour of an internal combustion engine under test-bed conditions shows differences to the emission behaviour under real in-use conditions. Because of this fact, the developers of combustion engines and the legislator are focussing on the measurement and optimization of real in-use emissions. To this day, the research, the adjustment of the carburettor and the legislation of small handheld engines is performed under test bench conditions, especially conditioned fuel pressure and temperature, as well as air temperature. Also the engines are laid out for two operation points: rated speed with full open throttle and idle speed. This test-procedure is used for all kinds of handheld off-road applications and does not consider the load profile of the different power tools. Especially applications with transient load profiles, for example chainsaws, work in more than two operating points in real use.

The two-stroke SI engine remains the dominant concept for handheld power tools. Its main advantages are a good power-to-weight ratio, simple mechanical design and low production costs. Because of these reasons, the two-stroke SI engine will remain the dominant engine in such applications for the foreseeable future. Increasingly stringent exhaust emission laws, in conjunction with the drive for more efficiency, have made new scavenging and combustion processes necessary. The main foci are to reduce raw emissions of unburned hydrocarbons via intelligent guidance of the fresh air-fuel mixture and to improve performance to reduce specific emissions. The flow velocity in the electrode gap of the spark plug is of great interest for the ignition of the air-fuel-mixture and the early combustion phase of all kinds of SI engines. In these investigations, the flow velocity in the spark plug gap of a two-stroke gasoline engine with stratified scavenging was measured under various conditions.