Search Results

Reflecting on the world's trend on saving crude oil consumption and to create an economical fuel efficient vehicle for the increasing world population, a new THS-II HV powertrain has been developed for the compact vehicle class. The application of a THS type powertrain for the compact vehicle class was a first for the world and to achieve it, brand new hardware, and software needed to be developed. For the Internal Combustion Engine (ICE), state of the art technologies such as the use of the Atkinson cycle with Variable Valve Timing (VVT), cooled exhaust gas recirculation (EGR), an electric water pump, a compact exhaust manifold, a Low Friction chain, beltless system and exhaust heat recovery system were applied. For the electric motor, copper wire with a rectangular cross section and divided stator cores combined with a newly developed production process were applied for higher volumetric density.

A new variable valve event and lift (VVEL) system has been developed by applying a multiple-link mechanism. This VVEL system can continuously vary the valve event angle and lift over a wide range from an exceptional small event angle and small lift and to a large event angle and large lift. This capability offers the potential to improve fuel economy, power output, emissions and other parameters of engine performance. The valve lift characteristics obtained with the VVEL system consist of a synthesis of the oscillatory motion characteristics of the multiple-link mechanism and the oscillating cam profile. With the multiple-link mechanism, the angular velocity of the oscillating cams varies during valve lift, but the valve lift characteristics incorporate both gentle ramp sections and sharp lift sections, the same as a conventional engine.

A continuously variable valve event and lift (VEL) system, actuated by oscillating cams, can provide optimum lift and event angles matching the engine operating conditions, thereby improving fuel economy, exhaust emission performance and power output. The VEL system allows small lift and event angles even in the engine operating region where the required intake air volume is small and the influence of valvetrain friction is substantial, such as during idling. Therefore, the system can reduce friction to lower levels than conventional valvetrains, which works to improve fuel economy. On the other hand, a distinct feature of oscillating cams is that their sliding velocity is zero at the time of peak lift, which differs from the behavior of conventional rotating cams. For that reason, it is assumed that the friction and lubrication characteristics of oscillating cams may differ from those of conventional cams.

A new variable valve actuation system that varies valve lift and timing events continuously has been devised and confirmed to substantially improve power and reduce fuel consumption when applied to a SI engine. The variable valve event and lift (VEL) system is a simple mechanism consisting of oscillating cams and linkages, enabling it to operate the valves smoothly even at high speed. Its compact size facilitates application to direct-acting valve trains and its ability to vary valve lift from a deactivated state (0) to a large lift amount allows the system to be used with a wide range of engine concepts. In this study, VEL was combined with a phase shifting function to enable the valve lift characteristic to be varied virtually arbitrarily, and test results showed that fuel consumption of a SI engine was reduced by nearly 10%.

This paper describes a new variable valve control device called VEL (Variable Valve Event and Lift Control Device), which enables continuous control of both valve events (opening duration) and valve lifts, from the lowest lift or deactivation state (0) to a long event and high lift state. VEL is composed of two subsystems. One is a mechanical valve train system, which converts crankshaft rotation into output cam oscillation via a transmission mechanism involving a rocker arm. The valves are moved by the output cam oscillation. The other is an electric powered actuator system, which varies valve events and lifts according to driving conditions by controlling the angular positions of a control shaft. This control shaft has a eccentric control cam inserted into the fulcrum cylinder of the rocker arm, so as to change the state of the transmission mechanism and the output cam.

This paper describes a new variable valve system that enables continuous control of valve events, i.e. time periods when the valve is open. In this system, valve events are controlled by varying the camshaft angular speed by means of an offset between the center of the camshaft and that of the medium member that transfers crankshaft torque to the camshaft. The medium member, a rotating disk, has a drive pin to enable the transfer of torque. The system has a mechanism that produces an offset between the center of the rotating disk and that of the camshaft as well as an actuator that drives the mechanism. This makes it possible to develop a compact system that can be installed in existing DOHC direct-acting valve train engines without making any major cylinder head modifications.

This study describes the construction and evaluation of a low energy house which should be in harmony with the environment and also be assisted by hybrid natural energy resources and unused energy. An experimental house with ground source heat pump (GSHP) was built in Hokkaido University, Japan in March, 1997. As a result of experiments, it was shown that approx. 80 % of the total energy was provided from PV modules, solar collectors, underground and exhaust heat. Annual energy consumption was 12.5 % of typical house’s one in Hokkaido. This report describes an outline of the low energy house and experimental energy balance.