Search Results

Different hybrid powertrains for a European mid-size passenger car were evaluated in this paper through numerical simulation. Different degrees of hybridizations, from micro to mild hybrids, and different architectures and power sources management strategies were taken into account, in order to obtain a preliminary assessment of the potentialities of different hybrid systems for the European passenger car market. Both diesel and gasoline internal combustion engines were considered: a 1.6 dm₃ Common Rail turbocharged diesel, and a 1.4 dm₃ spark ignition turbocharged engine, equipped with an innovative Variable Valve Actuation system. Diesel hybrid powertrains, although being subject to NOx emissions constraints that could jeopardize their benefits, offered substantial advantages in comparison with gasoline hybrid powertrains. Potentialities for fuel consumption reductions up to 25% over the NEDC were highlighted, approaching the 2020 EU 95 g/km CO₂ target.

Fuel consumption and NOx emissions of different Diesel-Electric hybrid powertrains, equipping a midsize European passenger car were evaluated in this paper through numerical simulation. Different degrees of hybridizations, from micro to mild hybrids, and different architectures and power sources management strategies were taken into account, in order to obtain a preliminary assessment of the potentialities of a Diesel-Electric hybrid system for the European passenger car market. Both regulated driving cycles, such as NEDC, and “real-world representative” driving cycles, such as Artemis cycles, were evaluated, in order to obtain not only an estimate of the impact of hybridization on type-approval CO2 and NOx emissions, but also an assessment of the impact of these technologies from the vehicle owner's perspective. Finally, the effects of internal combustion engine downsizing was also considered.

Experimental Design methodologies have been applied in conjunction with objective functions for the optimization of the internal geometry of a rear muffler of a subcompact car equipped with a 1.4 liters displacement s.i. turbocharged engine. The muffler also features an innovative variable geometry design. The definition of an objective function summarising the silencing capability of the muffler has been driving the optimization process with the aim to reduce the tailpipe noise while maintaining acceptable pressure losses and complying with severe space constraints. Design of Experiments techniques for the reduction of experimental plans have been shown to be extremely effective to find out the optimum values of the design parameters, allowing a remarkable reduction of the time required by the design process in comparison with full factorial designs.

The effect of variations of compression ratio (CR) and injection pressure (IP) on the emissions and performance of a small displacement common rail off-road diesel engine was evaluated. The operating point corresponding to the 5th mode of the ISO 8178 - C1 test cycle (intermediate speed / full load) was considered, since it represents one of the most critical operating conditions as far as exhaust emissions are concerned. The main effect of a reduction of the compression ratio, for a fixed injection timing, was found to be, as expected, an increase in NOx emissions along with a decrease of PM emissions, with a substantial redefinition of the PM-NOx trade-off curve; the choice of a proper value for the start of injection can therefore lead to a better compromise among pollutant emissions, although remarkable variations in BSFC and combustion noise must be taken into account.

In this work the formation and the evolution of the fuel spray emerging from a hollow-cone swirl injector were investigated. The first aim of the work was to set up a tool for fuel spray simulation in a CFD analysis that can offer a reasonable accuracy with no significant increment in the computational time. The analysis started from a theoretical formulation of the fuel flow inside the injector, based on the potential theory, obtaining an injector model which allows the calculation of the main spray characteristics usually required by the CFD analysis (i.e. droplet velocity, fuel film thickness, droplet size distribution). These parameters can be obtained only from spray cone angle and mass flow rate, which are the data commonly provided by injector manufacturers. Furthermore, a phenomenological approach was also presented, in order to properly simulate in CFD analysis the spray tip penetration in the dense spray zone, without requiring an increase of the spatial grid resolution.

Design of Experiments (DoE) methodologies have been applied in conjunction with objective functions to the experimental optimization of multiple injection strategies for a small displacement Common Rail (CR) off-road diesel engine. One operating point, which corresponds to the 5th mode of the ISO 8178 - C1 test cycle (intermediate speed / full load), was considered during this analysis: this operating condition is one of the most critical as far as exhaust emissions for the considered engine are concerned. Three injections were actuated per engine cycle during the experimental tests, with different strategies characterized by different timings and durations of each injection. It was found that DoE techniques for the reduction of experimental plans can be very effective in finding the optimum values for the injection parameters, leading to a remarkable reduction in the calibration process time, compared to full factorial designs.

The unsteady flow effects in two different close coupled catalytic converters were investigated in order to achieve a better understanding of the steady state experimental tests which are usually performed to evaluate a flow distribution. Firstly the validity of a CFD model was achieved through a comparison of some steady state simulations with the results of HWA experimental measurements. Several different formulations of the uniformity index, that were found in literature, were then compared, trying to highlight the strengths and shortcomings of each one. Further information was derived from a comparison of the two catalysts that were tested to achieve a general methodology that would be useful for future analysis. Finally, a new approach to evaluate the flow distribution using a steady state analysis was proposed by comparing the results of a transient simulation that was obtained for a whole engine cycle.

The influence of different multiple injection strategies on the emissions, combustion noise and BSFC (brake specific fuel consumption) of a small non-road diesel engine prototype equipped with a Common Rail (CR) fuel injection system has been analysed. The two most critical operating points according to the ISO 8178 - C1 test cycle as far as the exhaust emissions are concerned (Intermediate Speed/Full Load; Rated Speed/Full Load) were considered. Different injection strategies, each with a fixed number of consecutive injections (up to 4), were tested for the selected operating points. It was found that multiple injection strategies can be very effective also for small displacement non-road diesel engines in reducing particulate matter (PM), NOx and noise levels without increasing fuel consumption.

Fuel cell vehicles promise to become, in near future, competitive with conventional cars in terms of performance, efficiency and compliance with emission reduction schedules. However, many steps still have to be done, and a series of fundamental choices, such as high vs. low air pressure system options remain unresolved. Modeling can be a powerful instrument to evaluate different components or plant layout, and to predict the dynamic behavior of a fuel cell system. The first part of this paper illustrates the implementation of a direct engineering dynamic model of a load-following fuel cell vehicle. The modeling techniques, assumptions and basic equations are explained for each subsystem, with special attention to the air supply system, whose dynamic simulation was one of the primary targets of this work. Some of the simulation results are presented in the second part.

The application of computational methods for the development of a high performance four-stroke motorcycle engine has here been evaluated. A single dimension fluid dynamic code has been employed to simulate engine performance at full load, and data predicted from computer simulation have been compared with experimental results. After the abovementioned validation process, computer simulation techniques were applied to develop a variable geometry exhaust system so as to optimize volumetric efficiency over a wider speed range. These techniques proved to be powerful and effective in the identification of the modifications required to obtain the engine performance targets.

High pressure common-rail injection systems nowadays allow a very high degree of flexibility in the timing and quantity control of multiple injections, which can be used to obtain significant reductions in engine noise and emissions. The aim of this study is to develop a better understanding of the relationship between injection strategies and the combustion and emission formation process. Some multiple injection strategies (pilot-pilot-main and pilot-main-after) have therefore been analyzed to highlight their influence on soot, NOx, combustion noise and bsfc (brake specific fuel consumption) on a passenger car DI Diesel engine prototype. One operating point (2000×2 rpm/bar) was analyzed for the pilot-pilot-main injection strategy while two operating points (1500×5 and 2500×8 rpm/bar) were tested for the pilot-main-after injection strategy.

The influence of pilot injection timing and quantity on soot, NOx, combustion noise and bsfc has been analyzed on a passenger car DI Diesel engine prototype equipped with a common rail fuel injection system. The investigated engine operating points were 1500/5, 2000/2, 2500/8 rpm/bar, which are quite typical of EC driving cycles. For each of these operating conditions, the pilot injection quantity was varied by up to 15% of the total injected quantity and the pilot injection timing was varied between 32° and 1° crank angle degrees. The principal combustion characteristics were determined on the basis of the heat release, and a thorough statistical analysis was performed to infer the correlation between the combustion parameters and soot and NOx emissions.

A production six-hole conical sac-type nozzle incorporating a quartz window in one of the injection holes has been used in order to visualize the flow under cavitating flow conditions. Simultaneous variation of both the injection and the back chamber pressures allowed images to be obtained at various cavitation and Reynolds numbers for two different fixed needle lifts corresponding to the first- and the second-stage lift of two-stage injectors. The flow visualization system was based on a fast and high resolution CCD camera equipped with high magnification lenses which allowed details of the various flow regimes formed inside the injection hole to be identified. From the obtained images both hole cavitation initiated at the top inlet corner of the hole as well as string cavitation formed inside the sac volume and entering into the hole from the bottom corner, were identified to occur at different cavitation and Reynolds numbers.

The performance of two-stroke spark-ignition engines is greatly influenced by the scavenging process The variation of the crankcase clearance volume has here been investigated as a method for engine-load reduction. This method allows the reduction of the load without throttling or only by partial throttling with a theoretical increase of the engine efficiency. A comparison of two methods (air throttling and crankcase clearance volume variation) has therefore been carried out. The reduction of pumping work, due to the use of the variable crankcase clearance volume, has not always caused a consequent reduction of the specific fuel consumption. This is mainly due to deterioration of the scavenging process and to the occurrence of pre-ignition which occur above all at light loads.

Gasoline direct injection in two-stroke engines has led to even more advantageous results, in comparison with four-stroke engines, as far as unburned hydrocarbon emissions and fuel consumption are concerned. A new electronically controlled injection system has therefore been fitted in a crankcase-scavenged two-stroke engine, previously set up with indirect injection equipment. The comparison between the performance of the two gasoline feeding systems has highlighted the potential of the direct injection strategy. The direct injection system here tested has allowed the optimization of the engine torque characteristic at wide open throttle operating conditions. Moreover, the engine original exhaust system, has been replaced with an expansion-chamber exhaust-pipe system, in order to evaluate the impact of direct gasoline injection also with these optimized exhaust configuration.

The influence of injection pressure on the performance of a FIAT passenger car Diesel engine prototype equipped with a Common Rail Fuel Injection System has been investigated. An increase of the injection pressure from 1300 up to 1500 bar, during this research, has permitted the assessment of the effect of this parameter on the maximum power and on the smoke emissions. The tests were performed at 4000 rpm, with an equal mass of injected fuel. The influence of the injection advance has also been taken into consideration during this experimental analysis. The in-cylinder pressure was first detected and recorded, together with the brake torque and emissions; the in-cylinder pressure was then used for the determination of the principal combustion characteristics, on the basis of the heat release analysis. Finally, higher injection pressure could be used as an effective parameter to increase the maximum power angular speed.

The hypocycloid mechanism, in its basic or modified version, can be used in reciprocating machines as an alternative solution to the conventional crankshaft-connecting rod system. This kinematic device is quite old in concept, but still gives rise to some research since it has some positive mechanical features, and it allows several functions to be easily combined. In the hypocycloid mechanism in fact the connecting rod has a perfectly sinusoidal straight-line motion, a characteristic that theoretically reduces the piston side thrust to zero and permits a perfect balance of inertia forces without auxiliary rotating shafts. Moreover, by means of a second head with suitable seals that prevent leakage to the crankcase, the lower portion of the cylinder can be used as a second working chamber without using the crosshead thus reducing the dimensions of the double acting machine.

Due to their low specific speed, Periphery pumps, allow high heads with small flow rates and present performance curves with very stable features. This kind of pump is also smaller and simpler to construct than equivalent volumetric pumps though they have a fairly low efficiency, due to the inherent characteristics of their fluid-dynamic behaviour. Over the past few years, periphery pumps have been subject to more and more interest in the automotive field, as injection pumps in spark ignition engines, in fact, for this purpose, they are highly competitive due to their reduced dimensions, low cost, high reliability and good priming behaviour. In the past many theories were presented to explain the behaviour of periphery pumps and to calculate their performances, but these theories usually need extensive experimental support.

This work has been carried out on a two-cylinder s.i. automotive engine and it investigates spark advance, air-fuel ratio and variable valve overlap for low emissions and low fuel consumption, with an acceptable cyclic irregularity under idle conditions. An original application of a variable valve timing system, based on a passive electro-hydraulic link, has been used for this purpose. The instantaneous engine speed and in-cylinder pressure have been measured and recorded by means of an acquisition data system that allows both the determination and the comparison of some cyclic irregularity indexes, under different engine settings, at idle. The optimum spark advance, air-fuel ratio and valve overlap, which yield the best compromise between fuel consumption and cyclic irregularity, under idle operating conditions, have therefore been pointed out.