Search Results

Air pollution is a significant environmental issue, and exhaust emissions from internal combustion engines are one of the primary sources of harmful pollutants. The transportation sector, which includes road vehicles, contributes to a large share of these emissions. In Europe, the latest emission legislation (Euro 7) proposes more stringent limits and testing conditions for vehicle emissions. To meet these limits, the automotive industry is actively developing innovative exhaust emission-control technologies. With the growing prevalence of electrification, internal combustion engines are subject to continuous variations in load and engine speed, including phases where the engine is switched off. The result is an operating condition characterized by successive cold starts. In this context, the challenge in coping with the emission limits is to minimize the light-off time and prevent fast light-out conditions during idling or city driving.

The tightening trend of regulations on the levels of admitted pollutant emissions has given a great spur to the research work in the field of combustion and after-treatment devices. Despite the improvements that can be applied to the development of the combustion process, pollutant emissions cannot be reduced to zero; for this reason, the aftertreatment system will become a key component in the path to achieving near-zero emission levels. This study focuses on the numerical analysis and optimization of different metallic substrates, specifically developed for three-way catalyst (TWC) and Diesel oxidation catalyst (DOC) applications, to improve their thermal efficiency by reducing radial thermal losses through the outer mantle. The optimization process relies on computational fluid dynamics (CFD) simulations supported by experimental measurements to validate the numerical models carried out under uncoated conditions, where chemical reactions do not occur.

The automotive industry is undergoing a deep transformation that will shape its future for the next decades. In order to achieve the CO2 fleet average requirements, the share of electrified powertrain is rising. It is now possible to design powertrains using not only the highly efficient internal combustion engines (ICE) but also the newly developed electrical motors (eMotor) and batteries. This variety of technologies allows the design of sophisticated powertrain to better fulfill the requests not only regarding CO2 regulations but also of different markets, customer expectations and emission legislations. The increased variety of powertrains causes, on the other hand, some challenges regarding the exhaust after treatment systems (EATS) layout and emission control, considering the almost infinite possibilities to combine ICE and eMotor’s toque delivery to fulfill the customer desired drive profile.

Global automotive fuel economy and emissions pressures mean that 48 V hybridisation will become a significant presence in the passenger car market. The complexity of powertrain solutions is increasing in order to further improve fuel economy for hybrid vehicles and maintain robust emissions performance. However, this results in complex interactions between technologies which are difficult to identify through traditional development approaches, resulting in sub-optimal solutions for either vehicle attributes or cost. The results presented in this paper are from a simulation programme focussed on the optimisation of various advanced powertrain technologies on 48 V hybrid vehicle platforms. The technologies assessed include an electrically heated catalyst, an insulated turbocharger, an electric water pump and a thermal management module.

Since several decades, passenger cars and light duty vehicles (LDV) with spark-ignited engines reach full pollutant conversion during warm up conditions; the major challenge has been represented by the cold start and warming up strategies. The focus on technology developments of exhaust after treatment systems have been done in the thermal management in order to reach the warm up conditions as soon as possible. A new challenge is now represented by the Real Driving Emission (RDE) Regulation as this bring more various, and not any longer cycle defined, cold start conditions. On the other hand, once the full conversion has been reached, it would be beneficial for many Exhaust After Treatment System (EATS) components, e.g. for overall durability if the exhaust gas temperature could be lowered. To take significant further emission steps, approaching e.g. zero emission concepts, we investigate the use of Electrical Heating Catalyst (EHC) also including pre-heating.

Emission legislation for Off Road Engines is forcing the industry to review the engine design, introducing state of the art technology for many components and tailored exhaust gas after treatment architectures. Particulate matter reduction is a crucial issue to be addressed having an influence on overall engine performance and cost. At the present stage there is not a unilateral solution in the industry, as some manufacturers use a combination of very high fuel injection pressure and very efficient DOC, while others rely on the automotive derived DPF technology with active regeneration or SCR-only technology to reach EU Stage IV and US Tier4f. Considering the pros and cons of each solution, VM Motori decided to adopt an innovative solution consisting in a DOC followed by a partial-flow filter PM-Metalit® for the R750 Engine family. The advantages of this solution will be discussed in this paper along with the application work that has been carried over to reach the emission limit.

Recent engine development has been mainly driven by increased specific volumetric power and especially by fuel consumption minimization. On the other hand the stringent emission limits require a very fast cold start that can be reached only using tailored catalyst heating strategy. This kind of thermal management is widely used by engine manufactures although it leads to increased fuel consumption. This fuel penalty is usually higher for high power output engines that have a very low load during emission certification cycle leading to very low exhaust gas temperature and, consequently, the need of additional energy to increase the exhaust gas temperature is high. An alternative way to reach a fast light off minimizing fuel consumption increase is the use of an Electrical Heated Catalyst (EHC) that uses mechanical energy from the engine to generate the electrical energy to heat up the catalyst.

Future emission legislation for 2 and 3 wheelers in EU and many other Countries will introduce durability of pollution control devices. Along with a durable coating technology, the mechanical durability of the substrate must be ensured to guarantee the requested conversion efficiency for the entire life of the motorcycle. A traditional approach consisting in engine bench and vehicle testing is no more competitive considering the very short time to market needed in the motorcycle market and the relevant cost related to this kind of tests. For this reason a new time and cost efficient accelerated component durability test was developed, which can account for the combined effects of critical load at a metallic catalytic converter. This paper shows the methodology used to determine the critical stressors and their levels in real operating conditions by measuring and analyzing a broad range of vehicle test information.

It is well known that the optimal management of cold start is crucial to fulfill present and future emission legislation. During past years the catalytic converter has left its original under floor position to get increasingly closer to the engine in order to exploit higher exhaust gas temperature. Simultaneously, the exhaust gas temperature is becoming significantly lower, both in gasoline engines due to the extensive use of turbo charging, and in diesel engines thanks to very high combustion efficiency and in some cases the use of two stage turbo charging. A well established way to reach the catalyst light-off temperature fast enough to fulfill emission limits consists of artificially increasing the exhaust gas temperature. This has the drawback of a higher fuel consumption which conflicts with the tight CO2 targets now required of the OEMs.

Future stringent emission legislation will require high efficient catalytical systems. Along with engine out emission reduction and advanced wash coat solution the substrate technology will play a key role in order to keep system costs as low as possible. The development of metallic substrates over the past few years has shown that turbulent-like substrates increase specific catalytic efficiency. This has made it possible to enhance overall performance for a specific catalytic volume or reduce the volume while keeping catalytic efficiency constant. This paper focuses on the emission efficiency of standard, TS (Transversal Structure) and LS (Longitudinal Structure) metallic substrates. In a first measurement program, standard TS and LS substrates have been compared using a 150cc 4 Stroke engine in dynamic (ECE R40) conditions. In a second test standard and LS substrate have been tested.

Future tighter emission limits for 2 wheelers in Europe and worldwide will require a completely new approach in catalyst system design. In particular, the EU5 scenario, probably with the same emission limits as 4 wheelers and, for the first time, emission durability requirements, needs a new strategy to combine higher and durable conversion efficiency with the classical characteristics of 2 wheeler systems: low cost, low weight with minimum impact on exhaust system layout and engine out performances such as low fuel consumption and good power output. This paper deals with the investigation of innovative metallic substrates keeping constant, as a first step towards the development of an EU5 system, both washcoat technology and PGM loading. In particular the effect of turbulent structures in the substrate, using PE (Perforated Foils) and LS (Longitudinal Structure) have been thoroughly investigated in testing 400cpsi PE and LS substrates.

Exhaust after-treatment systems will have to become increasingly efficient in order to comply with the strict emission limits that will apply in the European Union and worldwide in future. Moreover, space constraints, weight and low pressure drop are just some of the issues that have to be addressed by an EU III-compliant catalytic system. The development of metallic substrates over the past few years has shown that turbulent-like substrates increase specific catalytic efficiency. This has made it possible to enhance overall performance for a specific catalytic volume or reduce the volume while keeping catalytic efficiency constant. This paper focuses on the emission efficiency of standard, TS and PE metallic substrates. A simulation tool and flow bench measurements were used to develop a test matrix with catalyst similar pressure drop in order to examine different cell densities, substrate lengths and coating technologies.

Modern Diesel Engines equipped with Common-Rail Direct Injection and EGR are characterized by an increasingly high combustion efficiency. Consequently the exhaust gas temperature, especially during a cold start, is significantly reduced compared to typical values measured in previous engine generations. This leads to a potential problem with CO emission limit compliance. The present paper deals with an experimental investigation of turbulent-flow metal substrates, carried out on a vehicle roller bench using a production 1.3 Liter diesel engine equipped passenger car. The tested metal supported catalysts proved to yield extremely high conversion rates both during cold start and in warm operation phase. The improved mass transfer efficiency of the advanced metal substrates is related on one hand to the optimized coating technology and, on the other hand, to the enhanced flow performance in the single converter channels which is caused by structured metal foils.

Future stringent emission levels for NOx and PM will lead to the introduction of innovative combustion processes for diesel engines, such as premixed combustion, with the results to enhance the engine out emission of HC and CO. Therefore very efficient oxidation catalyst will be needed to face this possible issue. This paper deals with the optimization of a EU IV exhaust system by means of innovative metal supported catalyst, as for example the Pre Turbo Catalyst and the Hybrid Catalyst in combination with dedicated catalyst coatings. Moreover a base study over the use of PM-Filter Catalyst has been made, to show the efficiency of such a device with EU IV engine calibration. The second part of the paper deals with the turbulent like structured foils substrates to have an even more efficient diesel oxidation catalyst with very high volumetric efficiency.

Future emission legislation can be met through substantial improvement in the effectiveness of the exhaust gas after-treatment system, the engine and the engine management system. For the catalytic converter, differentiation is necessary between the cold start behavior and the effectiveness at operating temperature. To be catalytically effective, a converter must be heated by the exhaust gas up to its light-off temperature. The major influential parameter for the light-off still is the supply of heat from the exhaust gas. Modification of the cold start calibration of engine control such as spark retard or increased idle speed can increase the temperature level of the exhaust gas. One further possibility is represented by a reduction of the critical mass ahead of the catalyst (exhaust manifold and pipe). Nevertheless the best measure to obtain optimal cold start effectiveness still seems to be locating the converter close to the engine.

Future stringent emission limits both in the European Community and USA require continuously increased conversion efficiency of exhaust after-treatment systems. Besides the obvious targets of fastest light-off performance, overall conversion efficiency and durability, catalytic converters for maximum output engines require highly optimized flow properties as well, in order to create minimum exhaust backpressure for low fuel consumption. This work deals with the design, development and serial introduction of a close coupled main catalyst system using the innovative technology of Perforated Foils (PE). By means of PE-technology, channel-to-channel gas mixing within the metal substrate could be achieved leading to dramatically reduced backpressure values compared with the conventional design.

Modern Diesel Engines equipped with Common-Rail Direct Injection, EGR and optimized combustion technology have been proven to reduce dramatically engine raw emissions both in terms of Nox and Particulate Matter. As a matter of fact the recently introduced FIAT 1.3 JTD 4 Cylinder Engine achieves Euro 4 limits with aid of conventional 2-way oxidation catalyst. Nevertheless some special applications, such as platforms with relatively higher gross vehicle weight possibly yield to PM-related issues. The present paper deals with the development program carried out to design a cost effective aftertreatment solution in order to address particulate matter tailpipe emissions. The major constraint of this development program was the extremely challenging packaging conditions and the absolute demand to avoid any major impact on the system design. The flow-through metal supported PM Filter Catalyst has been extensively tested on the specific vehicle application with aid of roller bench setup.

The effects of the internal geometry of catalytic converter channels on flow characteristics; exhaust backpressure and overall conversion efficiency have been investigated by means of both numerical simulations and experimental investigations. The numerical work has been carried out by means of a micro scale numerical tool specifically tailored for flow characteristics within converter channels. The results are discussed with aid of flow distribution patterns within the single cell and backpressure figures along the catalyst channel. The results of the numerical investigation provide information about the most efficient channel shapes. An experimental validation of the simulated results has been carried out with a production 3.6 liter, 6-cylinder engine on a dynamic test bench. Both modal and bag emission data have been measured during the FTP-Cycle.